OttLite Thrive LED Sanitizing Lamp with USB Charging

Introduction

Congratulations on purchasing the OttLite Thrive LED Sanitizing Lamp with USB Charging, featuring advanced natural lighting technology.

Important Safety Warnings

Battery Safety

CAUTION! This product contains a button battery. If swallowed, it could cause severe injury or death in just 2 hours. Seek medical attention immediately. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you suspect a battery has been swallowed or placed inside any part of the body, seek immediate medical attention. Battery disposal should comply with local regulations for hazardous materials; do not incinerate.

General Safety Warnings

WARNING: To prevent electric shock, ensure the lamp is not plugged in until all setup steps are complete.

• Turn lamp off and wait until the lamp head is cool before handling.
• The LED panel may get hot after several hours of continuous use. Do not place hands directly on the LED light panel.
• Never use with an extension cord unless the plug can be fully inserted into the receptacles.
• Do not alter the plug.
• The lamp head is not replaceable by the consumer.
• If the external flexible cable or cord of this luminaire is damaged, it must be exclusively replaced by the manufacturer, its service agent, or a similarly qualified person to avoid a hazard. Indoor use only.
• The light source of this luminaire is not replaceable; when it reaches the end of its life, the whole luminaire shall be replaced.

Common sense, caution, and care must be used with any electrical product.

Product Registration

Please complete the enclosed Product Registration Form and return it by mail, or register online at OttLite.com/warranty.

Setup and Operation

NOTE: This unit is fully assembled.

1. Remove the lamp from its packing and place the lamp body base (A) flat on a steady surface.
2. Connect the power adapter input (F) into connector (G) at the rear-bottom of the lamp.
3. Plug the power adapter (H) into a standard household 120V AC outlet. Use only the supplied power adapter to avoid damage or fire.

Power Switch and Modes

The power switch (B) is a touch switch that controls ON/OFF power, LED brightness settings, and the lamp's mode function.

• To turn ON: Touch (B) once.
• To adjust brightness: Touch (B) again. The lamp has 3 brightness settings.
• To turn OFF: A fourth touch will turn the light OFF.
• To change light modes: Touch and hold (B). The three modes are: ClearSun LED, Sanitizing, and ClearSun + Sanitizing. The ClearSun + Sanitizing mode uses both ClearSun LEDs and Sanitizing LEDs simultaneously for continuous cleaning while using the lamp.

Mode Indicators: The active mode is indicated by the light next to the icons:

• Indicator light (N) illuminated: ClearSun mode is on.
• Indicator light (P) illuminated: Sanitizing mode is on.
• Indicator lights (N and P) illuminated: ClearSun + Sanitizing mode is on.

Repositioning the Lamp

To reposition the light, hold the lamp base (A) steady and grasp either the flex-neck (C) or shade (D) as needed. Refer to [Diagram 1] for the lamp's maximum adjustment range. Do not force the shade outside the allowable adjustable range, as excessive adjustment may cause damage.

Control Panel Functions

Refer to the control panel (J) for setting functions:

• SETTING button: Use to set time and calendar. In alarm mode, press to turn off the alarm.
• MODE button (M): Press to set alarm and snooze.
• UP button (▲): In setting mode, press to increase.
• DOWN button (▼): In setting mode, press to decrease.

Calendar and Clock Setting

The control panel (J) for setting the calendar and clock is located on the bottom of the lamp body base (A). Refer to [Diagram 2] for clock operation layout and features.

• To enter setting mode: Under normal mode, press the SETTING button. Press it again for the next setting. The sequence is: HOUR → MINUTE → YEAR → MONTH → DAY.
• To quit setting mode: Press the MODE button (M). The lamp will also automatically quit to normal mode if idle for 60 seconds.
• To switch display format: Under normal mode, press the UP button (▲) to switch between 12-hour and 24-hour display.

Alarm and Snooze Function Setting

• To enter alarm mode: Under normal mode, press the MODE button (M). The alarm mode is indicated on screen by the alarm icon [R].
• To set the alarm: In alarm mode, press the SETTING button to enter alarm setting. Press the SETTING button again for the next setting. The sequence is: HOUR → MINUTE → SNOOZE → MUSIC, then exit.
• Music Tones: There are 8 music tones to select from.
• Adjusting Alarm Time: Press the UP button (▲) and DOWN button (▼) to adjust the alarm time sequence.
• Activate/Deactivate Alarm/Snooze: In alarm mode, press the UP button (▲) and DOWN button (▼) to turn the alarm and snooze function ON/OFF. The [Music Note icon] will light up on the display to indicate the alarm is set. The "Zzz" icon will appear on the display to indicate snooze is activated.
• Alarm Ringing: When the alarm time is reached, it will ring for 1 minute, then snooze and ring again. Press the SETTING button to turn OFF the alarm, or touch the UP button (▲) and DOWN button (▼) to activate snooze.
• Snooze Default: Snooze defaults to 60 minutes. This setting may be lost if power is interrupted.

Battery Replacement

This lamp uses a CR2032 battery. Refer to [Diagram 3] for battery replacement. The battery compartment (K) is located on the bottom of the lamp body base (A).

• To remove/install button cell battery: Use a screwdriver to remove the battery compartment door (M). Install the button cell battery with the "+" or flat side facing upward.

Power Adapter Specification

• Input: AC 100-240V, 50/60 Hz, 0.8A
• Output: 12V DC, 2.0A with a Male DC Plug

This lamp includes a 5V, 2.1A USB output port (L) located on the bottom rear of the lamp. The USB port can charge items such as tablets and cellular phones.