OttLite LED Sanitizing Lamp with Wireless Charging

Congratulations

You've purchased the finest in natural lighting technology with your new OttLite® product.

Setup Instructions

WARNING: To prevent electric shock, ensure the lamp is not plugged in until all steps are complete.

NOTE: THIS UNIT IS FULLY ASSEMBLED

Remove lamp from packing, placing lamp body base (A) flat on a steady surface.
Connect power adapter input (H) into connector (J) in the rear-bottom of the lamp.
Plug the power adapter (G) into a standard household 120V AC outlet. Note: Only use with the supplied power adapter to avoid damage or fire.
Turn the lamp ON & OFF using the power switch in the touch panel (B) located on top of base (A).
The touch panel (B) includes multiple "touch" keys that control the lamp’s mode and brightness within each mode. This lamp provides five levels of brightness. See Touch Key Panel Instructions section for operating instructions.
Control panel (Q) is used to set the lamp’s calendar, alarm setting, and display screen light. See Calendar and Clock Setting section for operating instructions.
Wireless charger for Qi-certified devices (F) is located in the center of the base (A). See Wireless Charging Instructions section for details.
To reposition the light, hold base (A) steady and grasp either lamp body (C) or shade (D) depending on needed adjustment.
Refer to Diagrams 1 and 2 for lamp maximum adjustment range. NOTE: DO NOT FORCE the shade or lamp body outside the allowable adjustable range as excessive adjustment may cause damage.

Parts Identification:

A: Lamp body base
B: Touch panel (power, brightness, mode control)
C: Lamp body
D: Shade (contains LED panel L)
E: Red charging indicator light
F: Wireless charger (for Qi-certified devices)
G: Power adapter
H: Power adapter input connector
J: Lamp power input connector
K: USB output port (5V, 2.1A)
L: LED panel (located in shade D)
N: ClearSun mode indicator light
P: Sanitizing mode indicator light
Q: Control panel (calendar, alarm, display brightness settings)

Touch Key Panel Instructions

To power the lamp and operate LED settings, lightly touch the required "key" to achieve the following:

Turn lamp "ON/OFF": touch the power key as needed.
To adjust brightness: touch the brightness keys (⬆️ / ⬇️) as needed.
Touch and hold the M [mode button] to change modes. The three modes are: ClearSun LED, Sanitizing, and ClearSun + Sanitizing. ClearSun + Sanitizing mode utilizes both the ClearSun LEDs and Sanitizing LEDs simultaneously for continuous cleaning while using the lamp.

NOTE: The active mode will be indicated by the lights (N and P) next to the icons. If indicator light (N) is illuminated, ClearSun mode is on. If indicator light (P) is illuminated, Sanitizing mode is on. If both indicator lights (N and P) are illuminated, ClearSun + Sanitizing mode is on.

Calendar and Clock Setting

NOTE: Control Panel (Q) for setting Calendar and Clock is located on the backside of lamp body (C).

To set time, push the [setting button] and the "hour" will flicker. Then touch the ⬆️ [up button] and ⬇️ [down button] to adjust the "hour." After "hour" setting, touch the [setting button] again to set the "minute," "year," "month," and "day."
In setting mode, touch the M [mode button] to exit the function, or operation will stop in one minute.
When not in setting mode, touch the ⬆️ [up button] to switch between "12h" and "24h" display.

Alarm & Snooze Function Setting

To set the alarm time, press the M [mode button] located on control panel (Q) to activate alarm setting mode. In alarm mode, touch the [setting button] to set the alarm time sequence: "Hour," "Minute," "Snooze," "Music," then exit. NOTE: There are 8 music tones to select.
Touch the ⬆️ [up button] and ⬇️ [down button] to adjust the alarm time sequence.
To activate the alarm, press the M [mode button] to activate the alarm setting mode and then press the ⬆️ [up button] and ⬇️ [down button] to turn ON/OFF the alarm and snooze function. A [alarm icon] will light up on the digital display to indicate the alarm is set. A [snooze icon] will light up to indicate snooze is activated.
When the alarm time is reached, the alarm will ring for 1 minute, then snooze and ring again. Touch the power key to turn off the alarm or touch the ⬆️ [up button] or ⬇️ [down button] to activate snooze. NOTE: Snooze defaults to 60 minutes if loss of power occurs.

Temperature Switch Setting

In normal mode, touch the ⬇️ [down button] to switch between °F and °C display.
To adjust display screen brightness, touch the [brightness key] to choose a suitable brightness setting. NOTE: Display screen defaults to "highest" brightness setting when power is initially applied.

Wireless Charging Instructions

Wireless charging requires a Qi-certified device. To determine if your device is Qi-certified, please visit the Wireless Power Consortium website.

To wirelessly charge a device, perform the following:
Place the device, which supports the Qi wireless charging standard, face up on the middle of the Qi wireless charging icon (F).
When the device is centered on the Qi wireless charging icon (F), a solid RED light (E) will indicate the device is charging properly. NOTE: If the RED light is blinking, this indicates the device is not charging and needs to be properly centered.
Check the charge level on your device periodically to determine when the device is fully charged. NOTE: The product DOES NOT provide any indication of when the device is fully charged.

CAUTION! DEVICE MAY BECOME WARM DURING CHARGING. THIS IS NORMAL AND PART OF THE PROCESS. CHARGING TIMES VARY BY DEVICE.

Safety Warnings

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:

Turn lamp off and WAIT UNTIL LAMP HEAD (D) AND ADAPTER (G) ARE COOL before handling.
The LED panel (L) located in shade (D) might get hot after several hours of continuous use. DO NOT place your hands directly on the LED light panel.
Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
Do not alter the plug.
The lamp head included with this unit cannot be replaced by the consumer.
INDOOR USE ONLY.

NOTE: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.

Battery Replacement

This lamp uses a CR2032 battery. For battery replacement, see Diagram 3. The battery compartment is located on the backside of lamp body (C).
To remove/install the button cell battery: remove the battery compartment door located in the lower half of body section (C) on the back-side of the lamp. To remove the battery compartment door, turn the screw counter-clockwise.
The button cell battery is to be installed with the "+" or flat side facing upward.
Attach the battery compartment door when finished and re-insert the screw. NOTE: DO NOT over-tighten the screw to avoid it being stripped.

Battery Safety Warning

CAUTION: DO NOT INGEST BATTERY; CHEMICAL BURN HAZARD!
This lamp contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

NOTE: Coin/button cell batteries are small, single cell devices having a diameter greater than their height.

Diagram Descriptions

Diagrams 1 and 2: Lamp Adjustment Range
Illustrate the maximum adjustable range of the lamp head and shade. Users are advised not to force the shade or lamp body beyond these limits to prevent damage.
Diagram 3: Battery Compartment
Shows the location of the CR2032 battery compartment on the back of the lamp body (C) and the screw used to open it.

Technical Specifications

Power Adapter: Input: AC 100-240V, 50/60 Hz, 1.0A; Output: 12V DC, 2.5A with a Male DC Plug
Qi Charger: Output: up to 5 Watts depending on device
USB Port: 5V, 2.1A output

Regulatory Information

FCC Part 15 Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

To maintain compliance with the RF exposure guidelines, place the product at least 20cm from nearby persons.

IC Canada Compliance

This device contains licence-exempt transmitter(s)/receiver that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.

CAN RSS-216/CNR-216

CAN ICES-005 (B)/NMB-005 (B)

CAUTION: Any change or modification to product not expressly recognized by OttLite Technologies voids OttLite's responsibility for proper function of product.

	OttLite LED Lamp with Wireless Charging and Rainbow Colour Changing Base User Manual Instructions and safety information for the OttLite LED Lamp with Wireless Charging and Rainbow Colour Changing Base, including assembly, operation, and maintenance.
	OttLite Charge Up LED Lamp with Wireless Charging User Manual User manual for the OttLite Charge Up LED Lamp with Wireless Charging (Model CS3QB0OW-CA). Includes setup, operation, safety, and wireless charging instructions.
	OttLite Wireless Charging LED Lamp with Phone Stand User Manual Instructions and safety information for the OttLite Wireless Charging LED Lamp with Phone Stand, including assembly, wireless charging, USB charging, and FCC compliance details.
	Enhance LED Sanitizing Lamp with USB Charging - User Manual User instructions and safety information for the OttLite Enhance LED Sanitizing Lamp with USB Charging, detailing assembly, operation, modes, and regulatory compliance.
	OttLite Wireless Charging LED Lamp with Colour Changing Base User Manual Instructions and safety warnings for the OttLite Wireless Charging LED Lamp with Colour Changing Base, including setup, operation, clock and alarm settings, wireless charging, and FCC compliance information.
	OttLite Refresh LED Sanitizing Lamp with Wireless Charging User Manual User manual for the OttLite Refresh LED Sanitizing Lamp with Wireless Charging, detailing setup, operation, safety warnings, and specifications.
	OttLite Thrive LED Sanitizing Lamp with USB Charging: User Manual and Safety Guide Comprehensive guide to the OttLite Thrive LED Sanitizing Lamp with USB Charging, covering setup, operation, features, safety warnings, and battery disposal.
	OttLite Merge LED Desk Lamp with Wireless Charging - Model CS7QAK1W - User Guide Get started with your OttLite Merge LED Desk Lamp with Wireless Charging (Model CS7QAK1W). This guide provides setup instructions, wireless charging details, USB port usage, safety warnings, and regulatory compliance information for this versatile desk lamp.