Neomounts DS15-625BL1 Tablet Stand

Product Overview & Dimensions

The Neomounts DS15-625BL1 is a versatile tablet stand designed for secure and ergonomic placement of your device. The diagram displays the Neomounts logo and product model DS15-625BL1. It illustrates key dimensions: base diameter (approximately 32mm), overall height (285mm), arm length (230mm), and tablet holder dimensions (129-181mm width, up to 246mm height). It also indicates adjustable tilt angles (+20° and -110°) and 360° rotation for the holder. The unit of measurement is millimeters (mm).

The product is known by various names in different languages, including: Tablet stand (EN), Tablet stand (NL), Tablet-Ständer (DE), Support de tablette (FR), Supporto per tablet (IT), Soporte para tableta (ES), Suporte para tablet (PT), Stå til tablet (DK), Nettbrett holder (NO), Ställ för surfplatta (SE), Tablettiteline (FI), Stojak na tablet (PL), Stojan na tablet (CS), Držiak na tablet (SK), Suport tabletă (RO).

Parts Included

The following parts are included in the package:

• A: Holder (x1)
• B: Base (x1)
• C: Arm (x1)
• D: VESA Plate (x1)
• E: 2mm Adhesive Pads (x4)
• F: 3mm Adhesive Pads (x4)
• G: 4mm Adhesive Pads (x4)
• H: M5x16 Screws (x3)
• I: M5x20 Screws (x4)
• J: ST6.3x55 Screws (x2)
• K: D6 Screws (x2)
• L: 3mm Screw (x1)
• M: Screw (Diameter 4mm) (x1)
• N: 4mm Screw (x1)

The following items are indicated as necessary but not included: [Tool Icon] (Tool), [Drill Icon] (Drill).

Assembly Instructions

Step 1: Mount the support to the base

Attach the support arm (C) to the base (B) using screws (L, M) and other components (D, N) as indicated in the diagram.

Step 2: Install the mount on a countertop

Secure the assembled mount to a flat surface. The diagram shows required drill hole diameter (approximately 4.5mm or 3/16 inch) and screw length (55mm or 2.2 inches) for mounting. Ensure the surface is stable.

Step 3: Attach the holder to the VESA plate

Connect the tablet holder (A) to the VESA plate (D) using screws (I) and hardware (J, K).

Step 4: Attach the adhesive pads

Affix the adhesive pads (E, F, G) to the holder. Use 2mm pads (E) for tablet depths of 7.5-8.5mm, 3mm pads (F) for depths of 6.5-7.5mm, and 4mm pads (G) for depths less than 6.5mm.

Step 5: Place the tablet in the holder and lock the holder

Insert the tablet into the holder and secure it firmly using the built-in clamps.

Step 6: Route the cables through the rod

Feed any necessary cables through the central support rod for a clean and organized setup.

Step 7: Adjust the mount to the desired position

Adjust the angle and position of the tablet holder and arm to achieve the optimal viewing angle and ergonomic setup.

Important Safety Information

General Safety: Read and retain this manual for future reference. Ensure installation is performed by qualified personnel. At least two people are recommended for installation.

Installation Environment: Avoid installation in environments with high temperatures, humidity, water, dust, fumes, shocks, or vibrations. Do not install near air conditioning vents or in direct bright light, as this may cause eye fatigue.

Mounting Surface: Install only on vertical surfaces. Ensure the mounting surface (wall, ceiling, floor) can support at least four times the combined weight of the display and mount.

Product Care: Do not modify parts or use damaged components. Tighten all screws securely but avoid over-tightening to prevent damage.

Warranty: The product warranty covers the mount body for 5 years. The manufacturer is not liable for damage due to improper installation or environmental factors.