Home Decorators Collection Lincoln 3-Light Semi-Flushmount Use and Care Guide

Contact Information

For questions, problems, or missing parts, please contact Home Decorators Collection Customer Service:

8 a.m. - 7 p.m., EST, Monday – Friday
9 a.m. – 6 p.m., EST, Saturday

1-800-986-3460

HOMEDEPOT.COM/HOMEDECORATORS

Table of Contents

• Safety Information
• Warranty
• Pre-Installation
• Installation
• Operation
• Care and Cleaning
• Troubleshooting

Safety Information

Consult a qualified electrician if you have any electrical questions. ?

CAUTION: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have resulted during shipping. If there is a defect in the wire, do not attempt installation. Please call our Customer Service Team at 1-800-986-3460.

WARNING: Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box. ⚠️

Warranty

This lighting fixture is warranted to be free from defects in materials and workmanship for a period of five (5) years from the date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer's obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer's discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or mishandling. This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and specifically disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor / expense costs involved in the replacement or repair of said product.

Contact the Customer Service Team at 1-800-986-3460 or visit www.homedepot.com/homedecorators.

Pre-Installation

Planning Installation

• Read all instructions before installation.
• To avoid damaging this product, assemble it on a soft, non-abrasive surface, such as carpet or cardboard.
• Keep your receipt and these instructions for proof of purchase.

Tools Required

Ladder ?, Safety glasses ?, Electrical tape ?, Phillips screwdriver ?, Flat blade screwdriver ?, Pliers ?, Wire strippers ✂️

Hardware Included

NOTE: Hardware not shown to actual size.

Package Contents

A - Canopy (1)
B - Rod (1)
C - Light fixture (1)
D - Shade (1)
E - Light bracket (3)
F - Glass (3)

Installation

1. Assembling the light fixture

• Place the glass (F) into the shade (D) and secure with the tabs.
• Secure the bottom of the light brackets (E) to the top of the shade (D) using the preinstalled finials.
• Attach the metal rod (B) to the canopy (A) and light fixture (C).
• Secure the top of the light brackets (E) to the canopy (A) using the finials (DD) and short screws (EE).

Diagram showing assembly of the light fixture components: canopy (A), rod (B), light fixture (C), shade (D), light brackets (E), and glass (F).

2. Attaching the mounting unit to the junction box

• Attach the mounting unit (AA) to the junction box (not included) with mounting screws (BB).

Diagram showing mounting unit (AA) attached to junction box with screws (BB).

3. Making the electrical connection

• Connect the copper wire from the light fixture (A) to the mounting unit (AA) by securing it with the pre-installed ground screw.
• Connect the black to black (power), the white to white (neutral), and copper wire to ground wire with the wire nuts (CC) and secure the wire nuts (CC) with electrical tape (not included).
• NOTE: If the wires from the fixture are the same color, attach the side with markings or letters to the black (positive) wire and the other to the white (neutral) wire.

Diagram showing electrical connections with wire nuts (CC).

4. Securing the light fixture

• Secure the canopy (A) of the light fixture (C) to the junction box by placing the holes in the canopy (A) over the support screws on the mounting unit (AA). Secure with the cap nuts (FF).

Diagram showing canopy (A) secured to mounting unit (AA) with cap nuts (FF).

5. Installing the light bulbs

• Install three E12 candelabra 60-watt bulbs (not included).

Diagram showing a light bulb being installed into a socket.

Operation

1. Turning the light on

• Turn the light switch on to activate the fixture. ▶️

Care and Cleaning

• Clean the lamp with a soft, dry cloth.
• Do not use any cleaners with chemicals, solvents, or harsh abrasives.

Troubleshooting