WINTHROP 3 LIGHT CHANDELIER
USE AND CARE GUIDE
Contact Information
Questions, problems, missing parts? Before returning to the store, call Home Decorators Collection Customer Service:
8 a.m. - 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday
1-800-986-3460
Visit us online: HOMEDEPOT.COM/HOMEDECORATORS
Thank you for choosing Home Decorators Collection! We appreciate your trust and confidence. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
Table of Contents
Safety Information
Consult a qualified electrician if you have any electrical questions.
⚠️ CAUTION: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have resulted during shipping. If there is a defect in the wire, do not attempt installation. Please call our Customer Service Team at 1-800-986-3460.
⚠️ WARNING: Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box.
Warranty
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer's only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer's discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or mishandling. This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor / expense costs involved in the replacement or repair of said product.
Contact the Customer Service Team at 1-800-986-3460 or visit www.homedepot.com/homedecorators.
Pre-Installation
Planning Installation
- Read all instructions before installation.
- This fixture can be installed as an up-light or as a down-light.
- To avoid damaging this product, assemble it on a soft, non-abrasive surface, such as carpet or cardboard.
- Keep your receipt and these instructions for proof of purchase.
Tools Required
- ? Ladder
- ? Safety goggles
- ? Electrical tape
- ➕ Phillips screwdriver
- ➖ Flat blade screwdriver
- ? Pliers
- ✂️ Wire strippers
Hardware Included
NOTE: Hardware not shown to actual size.
| Part | Description | Quantity |
|---|---|---|
| AA | Mounting bracket | 1 |
| BB | Mounting screw | 2 |
| CC | Wire nut | 3 |
Package Contents
The following parts are included in this package:
| Part | Description | Quantity |
|---|---|---|
| A | Light fixture | 1 |
| B | Canopy | 1 |
| C | Rod | 4 |
| D | Quick Connector | 1 |
| E | Crystal | 131 |
Diagram Description: The package contents are illustrated with labels A through E. Part A shows the main light fixture body. Part B is a circular canopy. Part C shows four identical rods. Part D is a small connector piece. Part E depicts individual crystals.
Installation
Step 1: Assembling the light fixture
Description: This step involves assembling the main components of the chandelier before mounting it.
- Screw the rods (C) to the top of the light fixture (A). Ensure to feed the branch wires through the rods during assembly.
- Attach the quick link (D) to the top rod (C).
- Attach the crystals (E) to the light fixture (A).
NOTE: Ensure the quick connector is fully closed when installing the chain.
Diagram Description: Shows the light fixture (A) with rods (C) being attached. A quick link (D) is shown connecting to the top rod. Crystals (E) are depicted being attached to the fixture body.
Step 2: Secure the light fixture
Description: This step details how to mount the fixture to the ceiling junction box.
- Attach the mounting unit (AA) to the junction box (not included) with the mounting screws (BB). Remove the pre-installed screw collar ring from the mounting unit.
- Place the canopy (B) over the pre-installed screw collar loop on the mounting unit (AA). Turn the screw collar ring until 1/2 of the screw collar loop threads are exposed.
- Secure the quick connector (D) to the screw collar loop on the mounting unit (AA). Lower the screw collar ring and canopy (B) over the quick connector (D).
- Weave the electrical wires and ground wires through the quick connector (D), screw collar loop, canopy (B), and through the center of the mounting unit (AA).
NOTE: Ensure the quick connector is fully closed when installing the chain.
Diagram Description: Illustrates attaching the mounting unit (AA) with screws (BB) to the ceiling. Shows placing the canopy (B) and securing it with the screw collar loop. Depicts threading wires through the quick connector (D) and canopy.
Step 3: Making the electrical connections
Description: Connects the fixture's wiring to the home's electrical supply.
- Connect the copper wire from the light fixture (A) to the mounting unit (AA) by securing it with the preinstalled ground screw.
- Connect the black wire to the black (power) wire, the white wire to the white (neutral) wire, and the copper wire to the ground wire using the wire nuts (CC). Secure connections with electrical tape (not included).
NOTE: If the wires from the fixture are the same color, attach the smooth wire with 'H' markings to the black (positive) wire and the ribbed wire with 'N' markings or letters to the white (neutral) wire.
Diagram Description: Shows electrical connections being made. One diagram illustrates connecting the fixture's copper wire to the ground screw on the mounting unit (AA). Another shows wire nuts (CC) being used to connect black-to-black, white-to-white, and copper-to-ground wires.
Step 4: Securing the light fixture
Description: Finalizes the attachment of the canopy to the ceiling.
- Secure the canopy (B) to the mounting unit (AA) with the screw collar ring.
Diagram Description: Shows the canopy (B) being attached to the mounting unit (AA) using the screw collar ring.
Step 5: Installing the light bulbs
Description: Installs the light bulbs into the fixture.
- Install 3 E12 60-watt bulbs (not included).
Diagram Description: Shows a light bulb being screwed into a socket on the fixture (A).
Operation
Turn the light switch on to activate the fixture.
Care and Cleaning
- Clean the lamp with a soft, dry cloth.
- Do not use any cleaners with chemicals, solvents, or harsh abrasives.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| The bulb will not light. | The bulb is burned out. | Replace the light bulb. |
| The power is off. | Ensure the power supply is On. | |
| There is a faulty wire connection. | Check the wiring. | |
| The fuse blows or circuit breaker trips when the light is turned on. | The circuit breaker is off. | Ensure the circuit breaker is in the ON position. |
| There are crossed wires or the power wire is grounding out. | Check the wire connections. Contact a qualified electrician or call the Customer Service Team at 1-800-986-3460. |
