Introduction
Thank you for choosing MelodySusie! Please read this instruction manual carefully and keep it in an accessible location so you may refer to it later.
Important Safeguards
READ ALL INSTRUCTIONS BEFORE USING.
⚠️ To reduce the risk of burns, electrocution, fire or injury to persons, please be sure to read the safety instructions below to avoid potential hazards that could result in personal injuries or damage to the device.
NOTE: If the USB cable connects to the adapter, it is recommended to use an adapter of 5V/2A. Please do not exceed 5V/2A, or the drill will burn out.
Section 1: Check Before Using
- Check the power supply cord before the first time use and during the life of the device. Do not use the device if it has a damaged cord, or if it is not working properly.
- Do not plug the device into a voltage system that is not specified on the cord. Use with improper voltage will damage the device and VOID warranty.
- Use the original cord only.
Section 2: Notes for Use
- To prevent electric leakage and shock or fire, do not draw out the connecting wires during use or touch the cord with a wet hand. Turn the power off after use.
- Do not use a crooked or damaged nail drill bit or replace the bit when power is on.
- Do not adjust the speed abruptly; stop use once unusual movement and noise happens.
- Misuse, dropping, or excessive force may cause device damage.
- Minors should not use this device without parental consent and supervision.
Section 3: Maintenance Work
- Do not disassemble the device. Doing so could be dangerous and constitutes voiding warranty conditions.
- Do not keep the device in a metal box, car, or other places at high temperature (more than 50°C). Keep the hand dry and away from oil and grease.
- Do not store the device in a hot or humid environment. Store it in a cool and dry place.
- Keep the electrical cord away from heated surfaces.
- Do not dispose of the device in heat or fire.
- Do not clean the device with harmful chemicals or detergents.
Section 4: Note for Injury
- Having manicures done frequently can cause injuries to the nails as well.
- If you need to remove gel polish from natural nails, try to use nail polish remover pads to avoid damage to the nail bed with improper operation.
- Do not use the device if you have an open wound on your nail or hand.
- If you have any skin diseases, heat-sensitive conditions, allergic reactions, onychomycosis, or any other disorder, you should consult your doctor and medical professionals before using the device.
Section 5: Safety Warnings & Disclaimers
Important Safety Information
⚠️ Before using this nail drill, carefully read and understand all safety instructions. Failure to follow these guidelines may result in injury or damage.
General Safety Precautions
- This device is for professional use only. Untrained individuals should not operate it.
- Always wear appropriate safety gear, including gloves, a dust mask, and protective eyewear.
- Keep children and pets away from the work area at all times, even when the device is not in use. Store the device in a secure, dry location out of reach of children when not in operation.
- Do not use in wet, humid, or flammable environments.
- Only use the manufacturer-approved power adapter to charge the device. Do not operate the unit while charging.
- If the device exhibits overheating, unusual noises, or electrical issues, stop use immediately and disconnect the power.
Usage Restrictions
- This device is only for nail care purposes. Do not use it for any unintended applications.
- Avoid applying excessive pressure while using the drill or excessive prolonged use to prevent overheating and nail damage.
- Do not operate if you are tired, under the influence of alcohol, or taking medication that impairs judgment.
- Avoid prolonged continuous use to prevent device overheating. A recommended usage time limit is 30-40 minutes per session, allowing the device to cool down between uses.
High-Risk Activities to Avoid
- Unauthorized Disassembly or Repairs: Disassembling or attempting to repair this device without professional training may result in malfunction or injury. Only qualified professionals should handle repairs.
- Damaged Accessories: Do not use worn-out or cracked drill bits.
- Avoid Entanglement: Keep hair, clothing, or brush bristles away from the nail drill to prevent them from getting caught in the machine.
- Excessive Pressure: Applying too much force can cause nail injuries or motor failure.
Strictly follow the safety instructions above to ensure the safe and proper use of the nail drill.
Section 6: Prohibited Actions & Potential Risks
Prohibited Action
- Using on wounded or infected nails
- Excessive filing on the nail surface
- Operating at excessive speed
- Using incorrect or misaligned drill bits (e.g., using at an angle or extending beyond the nail area)
- Consistently applying the drill to the same area for too long
- Failing to check the bit for stability before use
- Operating the drill without sufficient training
- Applying excessive pressure
- Changing drill bits without turning off the power
Potential Risk
- May cause severe irritation, pain, or infection
- May lead to nail thinning, breakage, infection, and discomfort
- Reduces precision and increases the risk of nail injury
- May cause skin or nail damage, bleeding, or infections
- May cause burns, discomfort, or nail fractures
- May lead to nail injuries due to unstable operation
- Higher risk of injury or improper nail treatment
- Leads to over-filing, thinning nails, and pain
- May result in accidental activation, causing injury
Disclaimers & Liability Limitation
- This device is manufactured to meet high safety and performance standards. However, improper usage, inadequate maintenance, or failure to follow instructions may lead to damage or personal injury, for which the manufacturer is not responsible.
- The manufacturer is not liable for injuries, damage, or losses resulting from unauthorized modifications, improper use, or failure to comply with the user manual.
- By using this device, the user acknowledges and accepts full responsibility for its proper and safe operation and agrees not to hold MelodySusie responsible for any harm, injury, or damage resulting from improper use.
- If you experience adverse reactions while using this product, such as skin irritation, burning sensations, or allergic reactions, discontinue use immediately and consult a medical professional. It is recommended to perform a patch test before first use to check for any sensitivity.
For Professional Use Only
This electric nail drill is intended for use by trained professionals in the beauty and nail industry. Do not attempt to use it without proper training. If in doubt, consult a qualified technician before operation.
By using this product, you agree to adhere to all instructions and acknowledge the potential risks associated with improper use.
If you need further assistance, please contact support@melodysusie.com or visit our website at www.melodysusie.com for troubleshooting and additional guidance.
Section 7: Six Drill Bits
The PC1201 Nail Drill comes with six different drill bits, each designed for specific tasks:
- Cone Bit: Pointed shape, used for under nail cleaning, cuticle work, and sidewall preparation.
- Safety Bit: Features a rounded tip, ideal for gentle cuticle work and polishing nail side edges.
- Mandrel + Sanding Bands: A cylindrical base that holds replaceable abrasive bands. Used for surface work, shortening nails, and removing product.
- Needle Head: A fine, pointed bit for precise work, such as polishing nail edges and cleaning cuticles.
- Small Barrel Bit: A small, cylindrical bit with a flat top, used for surface work and refining the nail.
- Large Barrel Bit: A wider, cylindrical bit with a flat top, suitable for surface work and shortening the nail.
Nail Drill Components
The nail drill unit and its power cord include the following components:
- DC Socket: The port where the power cord connects to the drill unit.
- Speed Controller: A mechanism (e.g., slider or dial) on the power cord to adjust the rotation speed of the drill bit.
- Control Switch: A switch on the power cord used to change the direction of rotation (clockwise or anticlockwise).
- ON/OFF F/R Button: A button or switch on the power cord that controls the power (ON/OFF) and potentially the rotation direction (F/R - Forward/Reverse).
Bit Insertion and Removal
- Take Out: The action of removing a drill bit from the drill head.
- Insert Into: The action of securely placing a drill bit into the drill head.
Section 8: How to Use
- Step 1: Insert the drill bit firmly into the drill head until it is secure.
- Step 2: Connect the nail drill power supply. The sliding switch on the power cord turns the drill on and off.
- Step 3: Move the control switch to the right for clockwise spin or to the left for anticlockwise spin. Slide the speed controller (also located on the power cord) to accelerate or decelerate the rotation speed.
- Step 4: After the polishing is finished, turn off the machine and return the control switch to the middle position.
Section 9: Problem and Terms of Settlement
| Malfunction | Reasons | Solutions |
|---|---|---|
| Changing the nail drill bit when the power is on. | 1. Motor burns out. 2. Bearing damages (Loud Noise). | Turn off the power when changing the nail drill bit. |
| When not in use, the speed is adjusted to the minimum, and the power is on. | 1. Motor burns out. 2. Device lifespan shortens. 3. Bearing damages (Loud noise). | Turn off the power when not in use. |
| Long time, large load work. | N/A (Implied cause of wear) | The continuous working time should not be too long when the working condition is in heavy load. When the device is overheating, it should be stopped immediately to make it return to normal. |
| Insert into a mismatched power cord. | 1. Motor burns out. | According to the device voltage requirements, insert the matching power cord. |
| Put the power cord at random/Pull the power cord. | 1. Power cord breaks. 2. Poor connection. | Do not pull the power cord. |
| Replace the original cord randomly. | 1. Motor burns out. 2. Easy to cause short circuit. | Use the original specification cord. |
| Dust into device/device drops to the ground or other impact. | 1. Battery damages (Loud noise) 2. Motor gets hot. 3. Rotational speed slows down. | Clean dust, add the dust-proof protection of the dustproof hood / Avoid device drops or by other impact. |
| Insert nail drill bit into the device incorrectly. | 1. Drill bit falls out. 2. High vibration. 3. Drill bit stuck. | Insert the nail drill bit into the device correctly. If the drill bit is stuck, please try to take it out harder. |
| The size of drill bit is not suitable. | Can not insert the drill bit into the device. | Use standard drill bit. |
| Water into the device/Operate in wet or moist conditions/ Use a wet cloth to clean the device. | 1. Motor burns out. 2. Device lifespan shortened. | Do not operate in wet or moist conditions. Only a dry cloth is allowed for cleaning. |
Section 10: Specifications
Max input voltage range: DC 5V/2A
For inquiries, please contact:
- Email: service@melodysusie.com
- Email: service.uk@melodysusie.com
- Website: www.melodysusie.com
Section 11: Warranty and Customer Service
MelodySusie offers a 6 months limited warranty on quality-related issues. Please apply for your extra 6 months warranty extension and download the instruction manual in other languages by registering on www.melodysusie.com if needed.
Thanks for purchasing MelodySusie's product. You can share your experience after receiving the product. If you require any technical support, please contact us.
Contact Information:
- Website: www.melodysusie.com
- US Service: service@melodysusie.com
- UK Service: service.uk@melodysusie.com
- FR Service: service.fr@melodysusie.com
- DE Service: service.de@melodysusie.com
- Address: Whipple Rd, Union City, CA 94578
Authorized Representatives:
- EC REP: E-CrossStu GmbH, 69 Mainzer Landstrasse, 60329 Frankfurt am Main, Hessen, Germany. Email: E-crossstu@web.de
- UK REP: YH Consulting Limited, C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX. Email: weel.keren@gmail.com
