MelodySusie Atena Cordless Nail Drill
Instruction Manual
Introduction
Thank you for choosing MelodySusie! Please read this user guide carefully and keep it in an accessible location so you may refer to it later.
Important Safeguards
READ ALL INSTRUCTIONS BEFORE USING.
[⚠] To reduce the risk of burns, electrocution, fire or injury to persons.
Please be sure to read the safety instructions as follow to avoid potential hazards that could result in personal injuries or damage to the device.
NOTE: If the USB cable connects to the adapter, it is recommended to use an adapter of 5V/2A. Please do not exceed 5V/2A, or the drill will burn out.
01 Check before Using
- Check the power supply cord before the first time use and during the life of the device. Do not use the device if it has a damaged cord or plug, or if it is not working properly.
- Do not plug the device into a voltage system that is not specified on the device or charger. Use with improper voltage will damage the device and VOID warranty.
- Use the original charger only.
02 Note for Battery
- The Battery needs to be charged fully before first use to ensure optimal performance.
- Do not overcharge the device or use it when it is charging. Charge the device in a well-ventilated condition with 0°C~40°C.
- Do not charge the device close to flammable or explosive materials. When charging the device, please do not cover it with clothes or other things.
- If the device is not used for long periods of time, you should charge and discharge once every three months. In normal conditions, the battery performance will decline over several years.
03 Note for Using
- To prevent electric leakage and shock or fire, do not draw out the connecting wires during use or touch the plug with a wet hand. Turn the power off after use.
- Do not use a crooked or damaged nail drill bit or replace the bit when power is on.
- Do not adjust the speed abruptly; stop use once unusual movement and noise happens.
- Misuse, dropping, or excessive force may cause device damage.
- Minors should not use this device without parental consent and supervision.
04 Maintenance Work
- Do not disassemble the device. Doing so could be dangerous and constitutes voiding warranty conditions.
- Do not keep the device in a metal box, car, or other places at high temperature (more than 50°C). Keep the handpiece dry and away from oil and grease.
- Do not store the device in a hot or humid environment. Store it in a cool and dry place.
- Keep the electrical cord away from heated surfaces.
- Do not dispose of the device in heat or fire.
- Do not clean the device with harmful chemicals or detergents.
05 Note for Injury
- Having manicures done frequently can cause injuries to the nails as well.
- If you need to remove gel polish from natural nails, try to use nail polish remover pads to avoid damage to the nail bed with improper operation.
- Do not use the device if you have an open wound on your nail or hand.
- If you have any skin diseases, heat-sensitivity, allergic reactions, onychomycosis, or any other disorder, you should consult your doctor and medical professionals before using the device.
06 Six Drill Bits
Descriptions of six drill bits:
- Needle Head: Polish nail edge.
- Cone: Under nails, cuticles, and sidewalls.
- Mandrel+ Sanding Bands: Surface work, shortening, and removal.
- Safety Bit: Cuticle work, polish nail side edge.
- Large Barrel: Surface work for backfill cutting, shorten, infill cuticle.
- Small Barrel: Surface work.
[Diagrams of drill bits are described above.]
07 How to Use?
- Choose one nail drill bit, release the handpiece, insert the drill bit into the handpiece and lock it in place.
- Press the ON/OFF button for 2 seconds to turn on or off the device.
- Press the Speed control to accelerate or decelerate the rotation speed.
- Change the rotation direction of the grinding drill bit on the F/R button if needed.
08 How to Replace Drill Bit?
Please make sure that the desired bit is suitable for the collet.
[Diagrams illustrating drill bit replacement: 1. Handpiece with barrel being turned clockwise to release bit. 2. Handpiece with a new bit being inserted. 3. Handpiece with barrel being turned counterclockwise to lock bit.]
[!] Do not move central barrel during operation.
- Turn central barrel clockwise until hearing a "click" sound to release drill bit. Take out the blank bar. Put the desired bit into the handpiece.
- Turn central barrel counterclockwise until hearing a "click" sound to lock drill bit in place.
- Be sure to confirm the rotation of the bit and collet. Please take care of your fingers not to be hurt by the bit edge.
09 Charging
- Take out the cord and connect it with the DC socket.
- The indicator light of the handpiece shows red and flashes, which means that the drill needs to be charged.
- The indicator light of the handpiece shows green or blue when the drill is fully charged.
10 Problem and Terms of Settlement
| Malfunction | Reasons | Solutions |
|---|---|---|
| Changing the nail drill bit when the power is on | 1. Motor burns out 2. Bearing damages (Loud Noise) |
Turn off the power when changing the nail drill bit. |
| The power is on when not in use | Turn off the power when not in use. | |
| Long time, Large load work | 1. Motor burns out 2. Device lifespan shortens 3. Bearing damages (Loud Noise) 4. Handpiece damages |
The continuous working time should not be too long when the working condition is in heavy load. When the device is overheating, it should be stopped immediately to make it return to normal temperature. |
| Insert into a mismatched power supply | 1. Motor burns out | According to the device voltage requirements, insert the matching power supply. |
| Put the power cord at random/Pull the power cord | 1. Device lifespan shortens 2. Power cord brokes 3. Poor connection 4. Easy to cause short circuit |
Do not pull the power cord. |
| Replace the original charger randomly | 1. Device damages 2. Easy to cause short circuit |
Use the original specification charger. |
| Dust into device | 1. Bearing damages (Loud Noise) 2. Motor gets hot 3. Rotational speed slows down 4. The potentiometer speed regulation fails 5. Handpiece damages |
Clean dust, add the dust-proof protection of the dustproof hood. |
| Device drops to the ground or by other impacts | 1. The ON/OFF button doesn't work 2. The potentiometer speed regulation fails 3. F/R button doesn't work 4. Handpiece damages |
Avoid device drops or by other impacts (If the handpiece was damaged, it can be purchased separately.) |
| Insert the nail drill bit into the device incorrectly / Rotate the central barrel into the place incorrectly / Take the drill bit out when the central barrel is locked | 1. Drill bit falls out 2. High vibration 3. Drill bit stucks 4. The Handpiece stucks and cannot be turned on 5. Handpiece damages |
Insert the nail drill bit into the device correctly/If the drill bit stucks, please release the handpiece and try to take out it hard/Rotate the central barrel correctly. |
| Replace drill bit when handpiece is not completely stopped | 1. The handpiece stucks and cannot be turned on 2. Handpiece damages |
Do not replace drill bit when handpiece is not completely stopped. |
| Overcharge | 1. Battery lifespan shortens | Not exceed the specified charging time. |
| The size of drill bit is not suitable | 1. Can not insert the drill bit into the device | Use standard drill bit. |
| Water into the device/Operate in wet or moist conditions/Use a wet cloth to clean the device | 1. Motor burns out 2. Device lifespan shortens |
Do not operate in wet or moist conditions/Only a dry cloth is allowed for cleaning. |
11 Specifications
Input voltage range: 5V/2A
E-mail: service@melodysusie.com
E-mail: service.uk@melodysusie.com
Website: www.melodysusie.com
12 Warranty and Customer Service
MelodySusie offers a 6 months limited warranty on quality related issues. Please apply for your extra 6 months warranty extension and download the instruction manual in other languages by registering on www.melodysusie.com if needed.
Thank you for purchasing from MelodySusie. You are welcome to share your experience after receiving the product. Please contact us for any technical support if needed.
Contact Information
Website: https://www.melodysusie.com
US Service: service@melodysusie.com
UK Service: service.uk@melodysusie.com
FR Service: service.fr@melodysusie.com
DE Service: service.de@melodysusie.com
Address: Whipple Rd, Union City, CA 94578
EU Representative: AMZLAB GmbH, Laubenhof 23, 45326 Essen, Germany
UK Representative: THEMIS AR support ltd., 85 Great Portland St. London, United Kingdom, W1W 7LT
