BRAYER Garment Steamer BR4128

Product Overview

The BRAYER BR4128 garment steamer is designed for the gentle smoothing of creases on clothing and interior textiles.

Description

The garment steamer consists of the following parts:

• 1. Water tank
• 2. Water inlet lid
• 3. Steam supply button
• 4. Operating surface with steam release openings
• 5. Operation indicator
• 6. Folding upper part of the body
• 7. Handle
• 8. Power cord
• 9. Base
• 10. Brush attachment

ATTENTION! For additional protection, it is recommended to install a residual current device (RCD) with a nominal operating current not exceeding 30 mA. Consult a specialist for RCD installation.

Diagram Description: A visual representation of the garment steamer is provided, illustrating the numbered components listed above.

Illustrations

Illustration 1: Depicts the BRAYER BR4128 garment steamer.

Illustration 2: Shows steam being released from the steamer's operating surface.

Illustration 3: Shows the garment steamer placed on its base.

Safety Measures and Operation Recommendations

Read these instructions carefully before use and keep them for future reference.

• Use the unit only for its intended purpose as described in this manual.
• Improper handling may cause breakage, harm to the user, or damage to property, which is not covered by warranty.
• Ensure the unit's operating voltage matches your home's mains voltage.
• The power cord has a "euro-plug"; insert it into a grounded socket.
• Do not use adapters to connect to the mains to prevent fire hazards.
• Do not touch the unit, power cord, or plug with wet hands.
• Do not operate the steamer with an empty water tank. Switch off and unplug when the tank is empty.
• Never leave the unit connected to the mains unattended.
• Do not use the unit outdoors or in bathrooms.
• Avoid using the unit during lightning storms.
• Protect the unit from impacts, falls, vibrations, and other mechanical stress.
• Do not use near heating appliances, heat sources, or open flames.
• Do not use near sinks, swimming pools, or other water containers.
• If the unit falls into water, immediately unplug it before retrieving it. Contact an authorized service center for inspection or repair.
• Do not use where aerosols are sprayed or near flammable liquids or their storage areas.
• Place the steamer vertically on a flat, dry, moisture- and heat-resistant surface. Do not place horizontally or turn it over.
• Use only the supplied attachment. Ensure it is properly set and fixed before use.
• Hold the steamer vertically during operation; do not turn it over.
• Fill the tank with water cleaned by a domestic filter. Do not use carbonated water or perfume additives.
• Ensure the water level does not exceed the MAX mark. Overfilling may cause water to splash out.
• Do not block or insert foreign objects into steam release openings.
• The upper part of the steamer body gets hot during operation. Hold by the handle to avoid burns.
• Avoid burns from hot steam.
• Never steam clothes while they are being worn; always use a hanger.
• Do not direct the steamer at people, animals, plants, furniture, electrical appliances, books, or other objects that could be damaged by hot steam. Maintain a distance of at least 20 cm from interior objects.
• Do not use the power cord as a handle; carry the unit by its handle.
• Unplug after use or before cleaning.
• Switch off and unplug the power cord from the mains socket.
• When unplugging, hold the plug and remove it carefully; do not pull the cord, as this can cause damage or a short circuit.
• For child safety, do not leave packaging polyethylene bags unattended.
• Attention! Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!
• The unit is not intended for use by children.
• Supervise children to prevent them from using the unit as a toy.
• Do not allow children to touch the operating surface, body, power cord, or plug during operation.
• Exercise extra caution if children or disabled persons are near the operating unit.
• During operation and breaks, keep the unit out of reach of children.
• The unit is not intended for usage by physically or mentally disabled persons (including children) or those lacking experience/knowledge, unless supervised or instructed by a responsible person.
• Periodically check the power cord for integrity.
• If the power cord is damaged, it must be replaced by the manufacturer, service center, or qualified personnel.
• Do not attempt self-repair or disassembly. If a malfunction occurs or the unit is dropped, unplug it and contact a service center.
• Transport the unit in its original packaging to prevent damage.
• Store the unit in a dry, cool place, out of reach of children and disabled persons.

Before First Use

After transportation or storage at negative temperatures, unpack the unit and wait at least 3 hours before use.

• Unpack and remove all packaging materials.
• Remove any protective film from the operating surface (4).
• Keep the original packaging.
• Read safety measures and operating recommendations.
• Check the delivery set.
• Inspect the unit for damage; do not plug it in if damaged.
• Verify that the unit's voltage specifications match your mains voltage. No additional settings are needed for 60 Hz mains.
• Wipe the steamer body with a slightly damp cloth and then dry it.

Garment Steamer Purpose

The garment steamer is used for smoothing folds on clothes or furniture.

• For uncertain fabrics, follow the garment's care label.
• If no information is available, test on the reverse side of the fabric.
• When steaming delicate fabrics like silk or corduroy, maintain a distance from the fabric.
• Use the brush attachment (10) to remove lint or threads.

Steamer Operation

Water Selection

• Fill the water tank (1) with tap water. If tap water is hard, mix with distilled water 1:1. For very hard water, use a 1:2 ratio or only distilled water.
• ATTENTION! Ensure the power cord (8) is unplugged before filling the tank (1).
• Open the steamer by lifting the upper part of the body (6).
• Open the water inlet lid (2). Fill the tank (1) up to the MAX mark and close the lid tightly (Fig. 1).
• Do not pour carbonated water, perfumed additives, vinegar, or chemicals into the tank (1).

Operating the Steamer

• ATTENTION! Do not plug in the steamer if the water tank (1) is empty.
• Place the steamer on the base (9) on a stable, flat surface.
• Plug the power cord (8) into the mains socket. The indicator (5) will light up. Wait 3-5 minutes for normal steam generation.
• Hold the steamer by the handle (7) at the level of the steam supply button (3).
• For continuous steam, press button (3) and slide it down until it stops (Fig. 2).
• To stop continuous steam, press button (3) and slide it upwards.
• Before first use, clean the steam chamber by directing steam onto a fabric (e.g., a kitchen towel).
• If the tank (1) runs out of water during operation, switch off and unplug the power cord (8) before refilling.
• After use, unplug the power cord (8) and let the steamer cool down.

Notes:

• An initial slight smell upon first use is normal.
• The steamer will automatically switch off after 8 minutes of continuous steam. The indicator (5) will flash. Press the steam supply button (3) again and wait for the operating surface (4) to heat up.

Using the Brush Attachment

• ATTENTION! Ensure the power cord (8) is unplugged before installing the brush (10).
• Install the brush attachment (10) onto the steamer.
• Open the water inlet lid (2). Fill the tank (1) with water, not exceeding the MAX mark, and close the lid tightly (Fig. 1).
• Do not pour carbonated water, perfumed additives, vinegar, or chemicals into the tank (1).
• Place the steamer on the base (9) on a stable, flat surface.
• Plug the power cord (8) into the mains socket. The indicator (5) will light up. Wait 3-5 minutes for normal steam generation.
• Hold the steamer by the handle (7) at the level of the steam supply button (3).
• Hang clothes on a hanger. Note: Do not steam clothes while worn due to high steam temperature; always use hangers.
• To switch on continuous steam, press button (3) and slide it down until it stops (Fig. 2).
• To switch off continuous steam, press button (3) and slide it upwards.
• Slowly run the brush attachment (10) over the fabric, straightening it with your free hand.

Notes:

• The steamer may automatically switch off after 8 minutes of steam supply. The indicator (5) will flash. Press the steam supply button (3) again and wait for the operating surface (4) to heat up.
• Keep the steamer upright during operation; do not turn it over.
• The upper part of the body (6) gets very hot during operation. Be careful not to touch the hot part of the body (6) or the operating surface (4).
• Steamed garments may take time to dry; leave them on hangers.

Cleaning and Care

• Unplug the power cord (8) and wait for the steamer to cool down completely.
• Open the lid (2) and pour out any remaining water, then replace the lid (2).
• Wipe the steamer body (6) and operating surface (4) with a slightly damp cloth, then dry.
• Mineral deposits on the operating surface (4) can be removed with a cloth soaked in an aqueous vinegar solution.
• Remove the brush attachment (10), rinse under running water, and dry it.
• Do not use abrasive cleaners or solvents.
• Do not immerse the steamer, power cord (8), or plug in water or other liquids.

Storage

• Unplug the steamer and wait for it to cool down completely.
• Clean the steamer.
• For convenient storage, fold the upper part of the body (6) (Fig. 3).
• Store in a dry, cool place, out of reach of children and disabled persons.

Delivery Set

• Garment steamer – 1 pc.
• Brush attachment – 1 pc.
• Manual – 1 pc.

Technical Specifications

• Power supply: 220-240 V, ~ 50/60 Hz
• Rated input power: 1500 W
• Water tank capacity: 120 ml
• Steam release: 20 g/min

Recycling

To prevent environmental damage or harm to health from uncontrolled waste disposal, do not discard the unit or batteries with household waste after their service life. Take them to specialized recycling stations.

Waste generated during product disposal is subject to mandatory collection and disposal according to regulations.

For more information on recycling, contact your local municipality, household waste disposal service, or the retailer where you purchased the product.

The manufacturer reserves the right to change design, structure, and specifications without prior notice, provided these changes do not affect the unit's general operating principles.

The unit's operating life is 3 years.

The manufacturing date is indicated in the serial number.

In case of malfunctions, contact an authorized service center promptly.