Tayogo Wireless Transmitter

Introduction

Thank you for purchasing Tayogo products. Please read these instructions carefully before use and use them correctly. Keep this manual safe for future reference.

Package Contents

• Wireless transmitter
• Antenna
• Charging cable
• Instruction manual

Product Specifications

Name of Each Part

The wireless transmitter features:

• Antenna: For signal transmission.
• Antenna socket: Where the antenna connects.
• Power button: Used for turning the device on/off and other functions.
• PPT button: For sending real-time voice instructions.
• Display: Shows channel information (e.g., CH:01) and status.
• Charging port: Type-C port for charging.
• Touch sensitive control buttons: For playback and channel selection (Previous, Play/Pause, Next).
• Microphone: For voice input.

About Antenna

1. Attachment: Place the antenna squarely on the socket and rotate clockwise to fully secure.
2. Remove: Rotate the antenna counterclockwise to remove.
3. Antenna Extension: Can be extended depending on the communication status.

Note: Do not use the antenna as a handle, as this may cause performance degradation due to damage. For long-term stable use, avoid frequent removal or bending of the antenna after installation.

How to Use the Transmitter

1. Attach the antenna to the transmitter.
2. Press and hold the power button for 3 seconds to power ON/OFF.
3. Press and hold the power button for 2 seconds to enable the touch buttons. The channel display will flash. Tap the [Previous] ◀️ or [Next] ▶️ buttons to adjust the transmitter channel. Press the power button again to lock the touch buttons (they will also lock automatically after 10 seconds of inactivity).
4. The transmitter's default channel is CH01. The headphones' default mode is Receiving Mode on CH01. The transmitter and headphone receiver will automatically connect the first time they are turned on.
5. Press the power button (while powered on) to check the battery level.
6. Connect your mobile phone to the T6 transmitter via Bluetooth: After the transmitter is switched on, the ? [Bluetooth] icon on the display will flash. When the Bluetooth connection is successful, the icon stops flashing.

Note: The headphone and the T6 transmitter must be set to the same channel.

Display Information:

• Channel display: CH:01~CH:16
• Blinking: Setting mode
• Lit: Current channel

Control Buttons:

• Short press [Previous] ◀️: Go to previous channel/song.
• [Play/Pause] ▶️/⏸️: Play or pause audio.
• Short press [Next] ▶️: Go to next channel/song.

Button Functions and Display Details

Power Button:

• Press and hold for 3 seconds to turn ON/OFF.
• Press and hold for 2 seconds to enable the touch buttons.
• Press to check the battery level.

Volume Adjustment: Volume is adjustable on the phone and the receiver headphone. Volume cannot be adjusted on the transmitter itself.

Play/Pause: Enable the screen touch buttons. Short press the [Play/Pause] button for music play/pause. The display icon indicates play state (light up) or pause state (off).

Display Status:

• Flashing: Waiting for connection
• On: Connected
• Off: Paused
• On: Playing

PPT Button: Under power ON condition, press and hold to send real-time voice instructions. Press the PPT button and tap volume buttons to adjust volume.

Volume Adjustment via PPT:

• Press the PPT key, simultaneously click [Volume Down] ◀️ to decrease volume.
• Press the PPT key, simultaneously click [Volume Up] ▶️ to increase volume.

Volume Value Display: (L:01-L:16)

Battery and Charging

Battery Level Indicator: Press the power button; the display will show the current amount of power remaining.

If the remaining battery power falls below 30%, the indicator will flash and an audible alert will be simultaneously notified by the headphone receiver.

CHARGING: Connect the transmitter to a standard USB port using the Type-C USB cable. The battery will be fully charged in approximately 2 to 3 hours. The transmitter supports 5V/3A input. Charging time may be longer if the charger's amperage is low.

Charging Indicators:

• Current power level display
• Blinking: Charging in progress
• Stop blinking: Charging complete
• Starts blinking when power level is less than 30

Important Notes

• Wireless transmitters are not waterproof. Do not wash them in water or use them underwater.
• When using the product for the first time, please charge it fully before use.
• Do not subject the product to strong shocks or drop it, as this may cause damage.
• Keep the product away from fire sources and high temperature environments to prevent damage due to overheating.
• Do not use the product in thunderstorms, storms, or other extreme weather conditions, as this may cause product malfunction or safety problems.
• For safety reasons, do not use the product while it is connected and charging.
• If the product is not used for long periods, it is recommended to charge the battery at least once a month to prevent battery degradation and extend product life.

PROPERTY SAFETY NOTICE: This product is designed for use with a mobile phone. If you are swimming alone, please ensure that your phone and transmitter are placed securely on shore or inside your bag. If your headphone suddenly loses signal while swimming, return to shore immediately to check whether your mobile phone and transmitter are still in place and have not been stolen.

After-Sales Service

Contact Us

If you have any questions, feel free to contact the Tayogo customer service team at: cs@tayogo.com.

Warranty Period

The warranty period for this product is 1 year from the date of purchase. Please understand that the warranty does not apply in cases of damage or poor function caused by misuse (such as falling), or in the case of alteration or repair by informal repairers.

Contact Information

Company Name: Dongguan Gaoyue Digital Technology Co., Ltd.

Address: Room 703, Building 13, No. 1 Jingdong Road, Fenggang Town, Dongguan City, Guangdong Province, China

Phone: +86-186-0306-0866

URL: www.tayogo.com

Email: cs@tayogo.com