Instruction Manual

Thank You

Thank you for purchasing this product. To achieve the perfect hidden-line effect, Game of Bricks uses thin aviation-grade wire with high tension and pressure tolerance. Due to its thin nature, please be careful not to cut through it, as it may be susceptible to shearing during installation. Always ensure not to press brick pieces down onto the wire.

Let's Get Started

If you encounter any challenges, please feel free to reach out via support@gameofbricks.eu. Game of Bricks offers 2 years of free light kit maintenance.

Step 1 (Bag 1)

This step involves preparing the components from Bag 1 and beginning the installation on the "STAR" portion of the logo.

Panel 1: Components from Bag 1 laid out: multiple LED strips with wires, a battery box, and a small bag labeled '1'.

Panel 2: The LED strips are shown connected to the battery box.

Panel 3: Three LED strips are displayed, illuminated.

Panel 4: The yellow brick-built "STAR WARS" logo.

Panel 5: A hand uses an orange tool to separate bricks on the "STAR" part of the logo, with an arrow indicating the action.

Panel 6: The "STAR WARS" logo with some bricks removed to allow for wire placement.

Panel 7: Hands route thin wires through the internal structure of the "STAR" letters, guided by green arrows.

Panel 8: A wire with red heat shrink tubing is prepared for connection.

Panel 9: Hands continue routing wires through the "STAR" letters, with green arrows indicating the path.

Panel 10: A wire with red heat shrink tubing is shown.

Panel 11: Wires are routed and connected within the "WARS" section of the logo.

Panel 12: The "STAR" portion of the logo with wires routed and secured.

Step 2 (Bag 2)

This step continues the installation process, focusing on the "WARS" portion of the logo.

Panel 1: Components from Bag 2 laid out: LED strips, wires, and a small bag labeled '2'.

Panel 2: The LED strips are shown connected to the battery box.

Panel 3: Three illuminated LED strips are displayed.

Panel 4: A thin wire with red tape is shown being prepared.

Panel 5: A hand routes a wire along the internal structure of the "WARS" letters, guided by green arrows.

Panel 6: Wires are routed and connected within the "WARS" letters, with green arrows showing placement.

Panel 7: A hand uses an orange tool to separate bricks, with an arrow indicating the action.

Panel 8: Wires are connected to components within the logo structure.

Panel 9: A wire is routed and secured, with green arrows indicating the path.

Panel 10: The "STAR WARS" logo is shown with wires routed and connected to the "WARS" section.

Panel 11: A hand routes a wire along the internal structure of the "STAR" letters, guided by green arrows.

Panel 12: Wires are routed and connected within the "STAR" letters.

Panel 13: A close-up shows a wire with red tape being prepared.

Panel 14: The "STAR WARS" logo is shown with wires routed and secured within the "STAR" section.

Step 3 (Bag 3)

This step involves installing the remaining lights, likely for the "STAR" portion, and completing the wiring.

Panel 1: Components from Bag 3 laid out: LED strips, wires, and a small bag labeled '3'.

Panel 2: The LED strips are shown connected to the battery box.

Panel 3: Three illuminated LED strips are displayed.

Panel 4: A thin wire with red tape is shown being prepared.

Panel 5: A hand routes a wire along the internal structure of the "STAR" letters, guided by green arrows.

Panel 6: Wires are routed and connected within the "STAR" letters, with green arrows showing placement.

Panel 7: The "STAR WARS" logo is shown with wires routed and connected to the "STAR" section.

Panel 8: A hand routes a wire along the internal structure of the "STAR" letters, guided by green arrows.

Panel 9: Wires are routed and connected within the "STAR" letters.

Panel 10: The "STAR WARS" logo is shown with wires routed and secured within the "STAR" section.

Panel 11: A hand routes a wire along the internal structure of the "STAR" letters, guided by green arrows.

Panel 12: The "STAR WARS" logo is shown with wires routed and connected to the "STAR" section.

Panel 13: The "STAR WARS" logo is shown from the back, with multiple wires extending from the illuminated letters.

Panel 14: The "STAR WARS" logo is shown from the back, with wires neatly arranged.

Step 4

This step involves connecting the power source and completing the installation.

Panel 1: A USB power cable with a red wire and a small connector is shown alongside several individual LED strips.

Panel 2: A hand connects LED strips to a connector block, with a green arrow indicating the connection point. A USB cable is also visible.

Panel 3: The "STAR WARS" logo is shown with the lighting system connected, displaying the illuminated letters.

Panel 4: The complete brick-built "STAR WARS" logo is illuminated, with LED lights shining brightly from within the letters. A light bulb icon ? indicates a successful illumination.

Final Connection

Connect the light kit to the battery box, and the installation will be complete. If you wish to use an alternative power source, please ensure its maximum voltage does not exceed 6V.