Instruction Manual
Light Kit for Kylo Ren's Tie Fighter 75179
Thank You
Thank you for purchasing this product. To achieve the perfect hidden-line effect, we use thin aviation-grade wire with high tension and pressure tolerance. However, due to its thin nature, be careful not to cut through it as it might be susceptible to shearing during installation. Always be careful not to press brick pieces down on the wire.
Let's Get Started
If you face any challenges, please feel free to reach out via support@gameofbricks.eu. Please note that we offer 2 years of free light kit maintenance.
Installation Process
Step 1: Prepare the Model and Components
Begin by ensuring your Kylo Ren's Tie Fighter 75179 model is assembled according to the LEGO instructions. Lay out all the components of the light kit. You should have several small LED lights with attached wires, connection cables, and possibly some special LEGO bricks for mounting the lights.
Image description: A hand is shown carefully attaching a red LEGO brick component to the underside of the Tie Fighter model.
Image description: Several red LEGO bricks and small LED components with wires are laid out on a wooden surface next to the Tie Fighter model.
Image description: A small plastic bag contains multiple small LED lights with thin red wires. The bag is labeled in Chinese and English, indicating '15cm Bit Light Red'.
Image description: The Tie Fighter model is shown with some red LEGO bricks already attached, and the small LED components with wires are being positioned near them.
Step 2: Install LED Lights
Carefully insert the small LED lights into designated areas of the Tie Fighter model. The wires should be routed discreetly through the existing gaps and structure of the LEGO bricks. Pay close attention to how the wires are positioned to avoid pinching or damage.
Image description: A close-up shows a hand inserting a small LED light into a red LEGO brick component.
Image description: Multiple LED lights with red wires are being placed into red LEGO brick components attached to the Tie Fighter.
Image description: A single LED light with a wire is being carefully inserted into a LEGO brick.
Image description: The Tie Fighter model is shown with several red LED lights installed in the rear engine area.
Step 3: Route and Connect Wires
Continue routing the wires from the LED lights towards the central connection point. Use the provided connection cables to link the LEDs. Ensure all connections are secure. Some steps may involve placing specific LEGO bricks over the wires to conceal and protect them.
Image description: Multiple red wires are being routed through the internal structure of the Tie Fighter.
Image description: A hand is shown connecting wires to a small circuit board or connector block within the model.
Image description: Several wires are neatly arranged and connected to a central point on the underside of the Tie Fighter.
Image description: The underside of the Tie Fighter shows multiple LED wires being connected to a series of ports.
Step 4: Secure and Conceal Wiring
As you progress, use the provided LEGO elements or existing model structure to secure and hide the wires. This ensures a clean look and prevents wires from interfering with the model's integrity or the lights' function.
Image description: A hand is carefully tucking wires into the gaps between LEGO bricks.
Image description: The internal structure of the Tie Fighter is shown with wires being routed and secured.
Image description: A close-up shows wires being fed through a specific LEGO element.
Image description: The Tie Fighter's main body is being reassembled, with wires carefully placed to be hidden.
Step 5: Connect to Power Source
Once all lights and wiring are in place, connect the main wire harness to the provided battery box or a compatible power source. Ensure the connection is firm.
Image description: Multiple LED wires are connected to a central hub or distribution board.
Image description: A USB connector is shown being plugged into a power source.
Image description: The completed light kit installation is shown, with some LEDs illuminated.
Image description: A hand is shown connecting the light kit's wiring harness to a USB power adapter.
Step 6: Final Check and Power Up
Connect the light kit to the battery box, and the installation will be complete. If you wish to use an alternative power source, ensure its maximum voltage does not exceed 6V.
Image description: The Tie Fighter model with the light kit installed, showing illuminated red and blue lights.
Image description: A close-up of the Tie Fighter's engine area, showing the red lights illuminated.
