Mi-Light RGBW Remote Control

Features

This manual describes two types of remote controls used for Mi-Light RGBW products. Both models share the same functions but feature different designs. The product utilizes the globally adopted 2.4GHz frequency with GFSK control method, offering low power consumption, long transmission distance, strong anti-interference, and fast communication rates. It employs a high-precision touch IC for stable and sensitive control, allowing users to adjust color, color temperature, saturation, and brightness of specified Mi-Light / MiBoxer smart lights.

Parameters

RGBW Remote (with buttons) - Model No.: FUT095

• Voltage: 3V (AAA * 2PCS)
• Transmission Frequency: 2.4GHz
• Modulation Method: GFSK
• Transmitting Power: 6dBm
• Standby Power Consumption: 20uA
• Control Distance: 30m
• Size: 52.5mm x 21mm x 120mm

[Diagram showing FUT095 remote with buttons labeled ON, OFF, M, S-, S+, and numbered zones 1-4]

RGBW Remote (Full Touch) - Model No.: FUT096

• Voltage: 3V (AAA * 2PCS)
• Transmission Frequency: 2.4GHz
• Modulation Method: GFSK
• Transmitting Power: 6dBm
• Standby Power Consumption: 20uA
• Control Distance: 30m
• Size: 52.5mm x 21mm x 120mm

[Diagram showing FUT096 full-touch remote with color ring, brightness slider, and buttons for ON, OFF, M, S-, S+, Zone ON, Zone OFF]

Products Key Diagram

Note: Hold the 'M' button to enter white mode. In white mode, press 'S-' for warm white and 'S+' for cool white. In color mode, press 'S+' or 'S-' to control saturation. When 'M' is pressed, 'S+' and 'S-' adjust the speed of dynamic modes.

To dim all RGBW lights simultaneously or change their color, first press 'Master ON'. To control individual lights, first press 'Zone ON' for the desired zone. Then, select the color or brightness using the color ring or brightness slider.

[Diagram illustrating the functions of the color ring, brightness control, Master ON/OFF, Zone ON/OFF, Speed control, and Mode selection for both FUT095 and FUT096 remotes. It shows how to link/unlink lights using the remote's buttons and zone selection.]

Linking & Unlinking

Linking Instructions

1. Switch off the light. After 10 seconds, switch it on again.
2. When the light is on, short press any zone button (e.g., 'Zone ON') 3 times within 3 seconds.
3. The light will blink 3 times slowly, indicating successful linking.

[Diagram illustrating the linking process: Power off, wait, power on, short press zone button 3 times.]

Note: If the light does not blink slowly, linking has failed. Switch the light off again and repeat the steps.

Unlinking Instructions

1. Switch off the light. After 10 seconds, switch it on again.
2. When the light is on, short press the same zone button 5 times within 3 seconds.
3. The light will blink 10 times quickly, indicating successful unlinking.

[Diagram illustrating the unlinking process: Power off, wait, power on, short press zone button 5 times.]

Note: Unlinking requires using the same zone as the linking process. If the light does not blink quickly, unlinking has failed. Switch the light off again and repeat the steps.

Grouping of Several Lights

An unlimited number of lights can be added to a zone on the 4-channel remote by linking them to different zones. This allows for flexible creation of different group combinations. Below are some grouping examples.

[Diagrams showing examples of grouping multiple lights into different zones using the remote.]

Remark:

• Users can reprogram as needed. One remote can control countless lamps or controllers, but each lamp or controller can be controlled by a maximum of four remotes.
• Ensure correct battery installation and controller power status (fully discharged if necessary) before programming after switching the power off and on.