1. Features
This manual describes two types of remote controls with same functions. Adopt world-wide used 2.4GHz frequency, GFSK control method, with the features of low power consumption, long distance transmitting, strong anti-interference and fast communication rate. Can control specified Mi-Light / MiBoxer smart light with color temperature and brightness changing.
2. Products Key Diagram
FUT006 Remote Diagram
The FUT006 remote features a central wheel for brightness/color temperature adjustment. Above the wheel are 'Master ON' and 'Master OFF' buttons. Below the wheel is a button to switch between brightness and color temperature modes. The bottom section has four zone control buttons: 'Zone ON' and 'Zone OFF' for each of the four zones. An indicator light labeled '4x(un) Link light' is also present.
FUT007 Remote Diagram
The FUT007 remote features dedicated buttons for color temperature and brightness. At the top are 'Master ON' and 'Master OFF' buttons. Below these are buttons for 'Warmer white' and 'Cooler white' color temperature adjustment. The bottom section includes '+' and '-' buttons for 'Brightness' adjustment, and four zone control buttons: 'Zone ON' and 'Zone OFF' for each of the four zones. An indicator light labeled '4x(un) Link light' is also present.
Operation Instructions
- To dim all dual white lights at once or change the color temperature, first press “Master ON”.
- To do this with individual lights, first press “Zone ON”. Secondly, set the adjustment for color temperature or brightness.
- To turn on the night light mode of a single (dual white) light, press and hold the “Zone OFF” from one of the 4 Zones.
- To turn on all the lights in night light mode, press and hold “Master OFF”.
- For remote control FUT006, the default mode is to adjust the brightness: rotating the wheel from left to right increases brightness, from right to left decreases brightness. Switching to adjusting the color temperature by pressing the middle button once: left to right makes it cooler, right to left makes it warmer.
3. Linking Code / Unlinking Code Instructions
Remark: The light can be working after linking with the remote.
Linking Code Instructions
Follow these steps to link a light to the remote:
- Switch off the light. After 10 seconds, switch it on again.
- Short press the "Link / Unlink" button 3 times within 3 seconds when the light is on.
- The lights will blink 3 times slowly, indicating that linking is done successfully.
⚠️ Linking failed if the light is not blinking slowly. Please follow the above steps again. (Note: Lights that have already been linked cannot be linked again.)
Unlinking Code Instructions
Follow these steps to unlink a light from the remote:
- Switch off the light. After 10 seconds, switch it on again.
- Short press the "Link / Unlink" button 5 times within 3 seconds when the light is on.
- The lights will blink 10 times quickly, indicating that unlinking is done successfully.
Important: Unlinking must be performed on the same zone used for linking.
⚠️ Unlinking failed if the light is not blinking quickly. Please follow the above steps again. (Note: Lights that have not been linked do not need to be unlinked.)
4. Grouping of several lights
You can add an endless number of lights to a zone on the 4-channel remote by linking lights to different zones. This allows for complete flexibility in creating different group combinations. Below are some grouping examples:
Grouping Examples
- Example 1: Shows lights connected to Zone 1, Zone 2, and Zone 3, indicating individual control or distinct groups.
- Example 2: Shows lights connected to Zone 1 and Zone 2, suggesting a smaller number of groups or combined lights within zones.
- Example 3: Shows lights connected to Zone 1, Zone 2, and Zone 3, similar to Example 1, demonstrating flexible distribution.
Remark:
- The user can reprogramme freely as needed. One remote can control countless lamps or controllers, but one lamp or controller can only be controlled by a maximum of four remotes.
- Please check the battery installation and controller (ensure total discharge of power) when you programme after switching off and switching on.
5. Attention
- This remote only controls specified Mi-Light / MiBoxer products; not all Mi-Light / MiBoxer series can work with this remote.
- If the indicated lamp blinks quickly during use, please change the battery in time. Do not use poor quality batteries to avoid damage to the remote from battery leakage.
- This 2.4GHz remote is a precise electronic product; do not use it in humid, high-temperature, dusty, or high-voltage environments. Store it in an indoor, dry, and static-electricity-free environment.
- Please do not use the remote near wide-range metal or strong electromagnetic wave areas, as this will badly affect the controlling distance.
Compliance Marks: CE, UKCA, RoHS
