HAMRON 004158 Bike Carrier
Model Number: 004158
This document provides operating instructions and safety guidelines for the HAMRON 004158 bike carrier. The instructions are available in multiple languages, with English serving as the primary language for this guide.
Product Description
The HAMRON 004158 is a bicycle carrier designed for mounting on a car's roof rack, allowing for the transport of bicycles.
Component Parts
The following parts are included with the bike carrier:
| Item No. | Component | Quantity |
|---|---|---|
| 1 | Main bike carrier frame assembly | 1 |
| 2 | Wheel holder/stop | 6 |
| 3 | Mounting plate/bracket | 1 |
| 4 | Bolt | 2 |
| 5 | Wheel strap | 2 |
| 6 | Wheel strap clip/holder | 2 |
| 7 | U-fastener/bracket | 2 |
| 8 | Mounting rail | 2 |
| 9 | U-bolt | 2 |
| 10 | Clamp/clip | 2 |
Safety Instructions
Read these instructions and safety instructions carefully before assembly and use. The manufacturer cannot accept liability for personal injury or material damage resulting from failure to follow the instructions.
- Be careful when driving through underpass, tunnel, car park, and garage etc.
- After driving a short distance, double-check that all screw unions and other connections are tight, and retighten if necessary. Re-check at regular intervals during the trip. Replace straps and screw unions immediately if they are worn or damaged.
- Braking and accelerate smoothly.
- Avoid sharp swerves. Do not turn at speeds over 40 km/h.
- Do not drive at speeds over 40 km/h in heavy traffic.
- Do not exceed speed limits. Never drive faster than 120 km/h with a bike on the bike carrier.
- Before starting and after driving a short distance, double-check that all screw unions and other connections are tight, and that the product is in good condition. Retighten, if necessary. Re-check at regular intervals during the trip.
- Do not cover bikes with material that can get blown away.
- Clean the product with a damp cloth or alcohol after use. Lubricate all screw unions with a suitable oil and store the product in a dry place. Remove the bike carrier before washing the car. Do not expose the product to solvents or caustic solutions.
Assembly and Usage
The bike carrier can be assembled and mounted in two different ways:
- With the U-fasteners round a square profile. (Illustrated in Figure 2)
- On a roof rack with T-slot. (Illustrated in Figure 3)
Mounting the Bike
Follow these steps to mount a bicycle onto the carrier:
- Start by opening the wheel straps on the wheel stops.
- Place the bike on the carrier as shown in the illustration. (Refer to Figure 4)
- Lock the bike frame by following steps 1-5. (Illustrated in Figure 4)
- Adjust if necessary the distance to the frame on the actual bike. (Refer to Figure 5)
- Adjust if necessary the distance between the wheel stops. (Refer to Figure 6)
- Tighten the wheel straps. (Refer to Figure 7)
- Remove all spanners and similar tools once the bike is secured. (Refer to Figure 8)
Diagram Descriptions
- Figure 1: Depicts the component parts of the bike carrier, corresponding to the table above.
- Figure 2: Illustrates the mounting method using U-fasteners for a square roof rack profile.
- Figure 3: Illustrates the mounting method for a roof rack with a T-slot.
- Figure 4: Shows the process of placing the bike on the carrier and securing its frame through a sequence of steps.
- Figure 5: Demonstrates adjusting the distance of the carrier's frame clamp to fit the specific bike's frame.
- Figure 6: Shows how to adjust the distance between the wheel stops to accommodate different wheel sizes.
- Figure 7: Illustrates the action of tightening the wheel straps to secure the bicycle's wheels.
- Figure 8: Shows the removal of all tools and accessories after the bike has been securely fastened.
- A magnified view shows a close-up of the wheel strap tightening mechanism.
- A magnified view highlights a warning symbol ⚠️, indicating potential hazards.
