FBH 0000 A

Safety Precautions

⚠️ DANGER: Risk of electric shock. Contact with live parts can be fatal.

Always disconnect power before performing any installation or connection work.

Installation Overview

The FBH 0000 A mounting frame has the following approximate dimensions:

• Height: 648mm
• Width: 450mm
• Depth: 71mm (main body)
• Additional depth considerations: 37mm, 216mm, 130mm
• Mounting area: 290mm ±0.5mm

Required Tools and Hardware

Tools:

• Screwdriver (PZ3) ?
• Drill ड्रिल
• Hammer ?

Hardware:

• 3x PZ2 screws (Ø 6 x 50 mm) ?
• 3x S8 screws (Ø 8 x 40 mm) ?
• 3x PZ3 screws (Ø 6 x 50 mm) ?
• Drill bit (Ø 8mm)

Mounting Instructions

Follow these steps for mounting the frame:

Step 1: Prepare Mounting Holes

For Brick/Concrete Walls: Mark the desired location. Drill holes using an 8mm drill bit to a suitable depth (e.g., 50mm). Ensure accurate placement using a template or the frame itself.

[Diagram Description: Illustrates drilling into a brick wall with an 8mm drill bit, showing hole depth and placement.]

Step 2: Insert Wall Plugs

Insert appropriate wall plugs into the prepared holes.

[Diagram Description: Shows a hammer tapping wall plugs into the drilled holes.]

Step 3: Secure Frame to Wall

Align the mounting frame with the prepared holes. Insert and tighten screws (e.g., S8 screws Ø 8 x 40 mm) to firmly attach the frame to the wall.

[Diagram Description: Depicts a drill with a PZ3 bit securing the frame to the wall using S8 screws.]

Alternative Mounting on Wood

For wooden surfaces, drill pilot holes using a PZ3 screwdriver bit. Secure the frame using appropriate screws (e.g., PZ3 screws Ø 6 x 50 mm).

[Diagram Description: Shows drilling pilot holes into wood and then screwing the frame using a PZ3 screwdriver.]

Step 4: Final Securing

Confirm that all mounting points are securely fastened. The diagrams show the frame being attached to the wall with screws, ensuring a stable installation.

[Diagram Description: Illustrates the frame being attached to the wall with screws, possibly showing different screw types or orientations for final securing.]

Internal Wiring Connections

The internal layout of the frame includes pathways for routing various colored wires (e.g., blue, green/yellow, brown, black, red) to designated connection points and terminal blocks.

[Diagram Description: Shows the internal structure of the frame with wires being routed to connection points.]

Power Connection

The mounting frame operates on a power supply of 100-240 V AC, 50-60 Hz.

Connection terminals are clearly labeled:

• L1: Live [Live]
• N: Neutral [Neutral]
• G: Ground [Ground]

Ensure correct polarity and secure connections to the power source.

[Diagram Description: Close-up of the terminal block showing L1, N, G labels and indicating the input voltage and frequency range.]

Stability Considerations

Mounting Frame Fillers

For optimal structural stability, it is crucial to install the frame filler pieces (indicated by 'X' in the diagram) after the main installation is complete.

[Diagram Description: Shows the main frame with 'X' marks indicating the locations where frame filler pieces must be installed for stability.]

Manufacturer Information

Bosch Sicherheitssysteme GmbH

Robert-Koch-Strasse 100

D-85521 Ottobrunn

Germany

Telefon: +49 (0)89 6290-0

Telefax: +49 (0)89 6290-1020

Website: www.boschsecurity.com

© Bosch Sicherheitssysteme GmbH, 2009