VEVOR Powder Filling Machine User Manual

Product Models

This manual covers the following VEVOR Powder Filling Machine models:

• F-100-V1, F-100-V2, F-100-V3
• F-200-V1, F-200-V2
• F-500-V1, F-500-V2
• F-999-V1, F-999-V2, F-999-V3
• F-3000-V2
• F-5000-V2

VEVOR: TOUGH TOOLS, HALF PRICE

General Safety Rules

WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.

Important Reminders:

• Before use, carefully read the product manual and ensure understanding and compliance with all safety warnings and usage precautions.
• Do not use this product for non-designated purposes to avoid unexpected risks.
• This product is only applicable to users within the specified age group and scope of application. Strictly comply with relevant age restrictions and warnings.
• If any abnormalities occur, stop using the product immediately and contact the after-sales service center for consultation or repair.

Environmental Requirements for Use:

• Use in a dry and well-ventilated environment, avoiding extreme conditions like water activation, high temperature, high humidity, and extremely low temperature.
• Avoid direct sunlight or contact with fire sources to prevent product damage or fire.
• Ensure a stable usage environment and prevent the product from being hit or dropped to avoid damage.

Safety Operation Guidelines:

• Use a suitable power supply and voltage; do not use damaged power cords or plugs.
• Do not short-circuit circuits or connect mismatched devices to avoid risks such as electric shock and fire.
• If foreign objects are found on the product surface, stop use immediately and remove them before continuing.
• When using continuously for a long time, rest periodically to avoid excessive fatigue.
• Do not plug or unplug the power plug with wet hands to avoid the risk of electric shock.

Maintenance and Upkeep

• Regularly maintain and clean the product. Before cleaning, disconnect the power supply and wipe with a dry cloth. Avoid alcohol, acid, or alkali solutions.
• When the product is not in use for an extended period, disconnect the power supply to save energy and extend its lifespan.
• Do not disassemble or replace components yourself. Contact the after-sales service center for any malfunctions.

Emergency Handling Measures

• In case of abnormal situations or accidents, stop using the product immediately.
• If overheating, smoking, or abnormal sounds occur, immediately cut off the power supply and contact the after-sales service center.
• For emergencies that may harm personal safety, call the emergency rescue number promptly.

SAVE THESE INSTRUCTIONS

Model and Parameters

Models F-100-V1, F-100-V2, F-100-V3, F-200-V1, F-200-V2, F-500-V1, F-500-V2

Models F-999-V1, F-999-V2, F-999-V3, F-3000-V2, F-5000-V2

Structure Diagram

Models F-100-V1, F-100-V2, F-100-V3, F-200-V1, F-200-V2, F-500-V1, F-500-V2

A diagram shows the machine with numbered parts:

• 1. Hopper
• 2. Adjusting Plate
• 3. Host Machine
• 4. Outlet
• 5. Control Panel

Models F-999-V1, F-999-V2, F-999-V3, F-3000-V2, F-5000-V2

A diagram shows the machine with numbered parts:

• 1. Hopper
• 2. Adjusting Plate
• 3. Host Machine
• 4. Power Outlet
• 5. Outlet
• 6. Control Panel

Components

Operating Instructions

For Models F-100-V1, F-100-V2, F-100-V3, F-200-V1, F-200-V2:

1. Lay the product flat and remove screws (A, B) as indicated.
2. Place the product in a stable position, plug in the power cord, and it is ready for use.

A diagram illustrates removing screws labeled A and B.

For Models F-500-V1, F-500-V2:

1. Open the buckle on the back cover, remove the cover, and then remove screws according to label instructions. Reattach the back cover.
2. Place the product in a stable position, plug in the power cord, and it is ready for use.

A diagram shows opening a buckle and removing the back cover.

For Models F-999-V1, F-999-V2, F-3000-V2, F-5000-V2:

1. Hopper Installation: Remove the installed screws. Insert the hopper and secure it with the removed screws. Ensure the side with the adjusting plate faces forward.
2. Plug in the power cord and pedal switch as shown.
3. Remove screws according to label instructions.

Diagrams show hopper installation and connecting the power cord and pedal switch.

Operating the Machine (General Instructions):

For Models F-100-V1, F-100-V2, F-100-V3, F-200-V1, F-200-V2, F-500-V1, F-500-V2, F-999-V1, F-999-V2, F-999-V3:

1. Turn on the power switch. The machine will sound and enter a standby state.
2. Press "Discharge" and then "Clear" to zero the "Weight (g)" display.
3. Set the desired weight by pressing "Weight +/-" (e.g., 08.0 for 8 grams).
4. Lower the adjustment plate to the lowest position. Load material into the hopper. Press the "Start" key. Adjust the position of the adjustment plate as needed for filling.
5. Select the desired speed ("Fast", "Medium", "Slow") based on the material on the control panel.
6. Press "Start". The machine begins working. When a "tick" sound is heard, filling is complete. Place a container at the discharge port to receive material. The container should be close to the sensor to trigger filling. Remove the container for the next automatic filling cycle.

Note:

• To clear, press the "Clear" key.
• To remove remaining material, hold down the "Discharge" key for 5 seconds while the machine is stopped. The machine will continue working until the material is finished. Press the "Stop" key to stop. Ensure the adjustment plate is fully open.

A diagram shows the control panel with buttons for Weight, Quantity, Speed, Start, Stop, Discharge, Clear, etc.

For Models F-3000-V2, F-5000-V2:

1. Turn on the power switch.
2. Press "Discharge" and then "Zero" to zero the "Weight (g)" display.
3. Set the desired weight by pressing "+/- " (e.g., 0800 for 800 grams).
4. Lower the adjustment plate to the lowest position. Load material into the hopper. Press the "Start" key. Adjust the position of the adjustment plate as needed for filling.
5. Select the desired speed ("Fast", "Medium", "Slow") on the control panel.
6. Press "Start". The machine begins working. When a "tick" sound is heard, filling is complete. Place the bag over the discharge port and press the foot switch to automatically discharge the material. After discharging, the machine automatically proceeds to the next filling round.

Note:

• To remove remaining material, press the "Cleaning material" key while the machine is stopped. The machine will continue working until the material is finished. Press the "Stop" key to stop. Ensure the adjustment plate is fully open.

A diagram shows the control panel with buttons for Weight, Quantity, Speed, Start, Stop, Discharge, Zero, etc.

Maintenance

1. Select a quantitative filling machine of a suitable range according to the products being filled.
2. The machine uses a precision electronic scale; overloading is forbidden.
3. Keep the machine level and stable during use to avoid damage from vibrations or impact.
4. After use, clean the material and maintain the machine's cleanliness.
5. When not in use, empty the materials and store the machine in a ventilated and dry place.
6. Clean the product and filter promptly after each use.
7. Always keep the product's exterior clean.
8. Store the product in a dry and ventilated place.

If the fuse is damaged, replace it as shown in the diagram. The diagram shows a fuse holder on the back of the machine.

Troubleshooting

Manufacturer and Contact Information

Manufacturer: Shanghai muxinmuyeyouxiangongsi
Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai

EC REP: SHUNSHUN GmbH
Address: Römeräcker 9 Z2021, 76351 Linkenheim-Hochstetten, Germany
Tel: +49 1727041930
Email: euvertreter@gmail.com

UK REP: Pooledas Group Ltd
Address: Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom
Tel: 01772418127
Email: pooledas123@gmail.com

Imported to AUS: SIHAO PTY LTD.
Address: 1 ROKEVA STREET EASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd.
Address: Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

Made In China