VEVOR
TOUGH TOOLS, HALF PRICE
Technical Support and E-Warranty Certificate
www.vevor.com/support
VACUUM PACKING MACHINE USER MANUAL
Model: DZ-260A-V1, DZ-260A-V2, DZ-260A-V3,
DZ-260S-V1, DZ-260S-V2, DZ-260S-V3
VEVOR is committed to providing tools at competitive prices. Expressions like "Save Half" or "Half Price" represent an estimate of potential savings compared to major top brands and may not cover all product categories. Customers are advised to verify savings carefully when placing orders.
Product Images
Image 1: Front view of the DZ-260A Vacuum Packing Machine.
Image 2: Front view of the DZ-260S Vacuum Packing Machine.
Models Shown:
- DZ-260A-V1, DZ-260A-V2, DZ-260A-V3
- DZ-260S-V1, DZ-260S-V2, DZ-260S-V3
NEED HELP? CONTACT US!
For product questions or technical support, please contact:
Technical Support and E-Warranty Certificate
www.vevor.com/support
This is the original instruction manual. Please read all instructions carefully before operating. VEVOR reserves the right to interpret its user manual. Product appearance is subject to the item received. VEVOR will not provide separate notification for technology or software updates.
⚠️ WARNING
- Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating.
- Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
GENERAL SAFETY RULES
Please read the entire operating instructions before using the products for the first time; they contain important information about correct operation.
The guarantee/warranty will be void if damage is incurred resulting from non-compliance with the operating instructions. Liability for any and all consequential damage is excluded. VEVOR assumes no liability for damage to property or personal injury caused by improper use or failure to observe safety instructions. In such cases, the guarantee/warranty will be void.
Unauthorized conversion, modification, or disassembly of the products is inadmissible due to safety and approval reasons (CE).
The product is not a toy and must be kept out of the reach of children. Particular care must be exercised if children are present.
The product must not get damp or wet; it is only intended for use in dry, indoor locations (not bathrooms or similarly damp areas). There is a risk of a fatal electric shock.
Do not expose the product or its accessories to damp or extremely high or low temperatures.
Do not leave packing materials unattended, as they may become dangerous playing material for children.
Dropping, falling, pressure, or tensile forces could destroy or at least limit the function of the product.
Never position the device in the vicinity of combustible or easily inflammable materials.
Always make sure that the rotary table on which the object is placed is located in the center of the housing.
This machine uses plastic film or plastic aluminum film for vacuum packaging paste foods, fruits, sauce vegetables, chemicals, pharmaceuticals, electronic components, precision instruments, rare metals, and other items. Products packaged under vacuum are not easily oxidized or moldy. It is especially suitable for industries such as tea, food, and medicine.
If you have reason to assume that safe operation is no longer possible, disconnect the device immediately and secure it against inadvertent operation.
It can be assumed that safe operation is no longer possible if:
- The device shows visible signs of damage.
- The device no longer functions.
- After a longer period of storage under unfavorable conditions.
- Following heavy stress during transportation.
SAVE THESE INSTRUCTIONS
MODEL AND PARAMETERS
| Model | DZ-260 A-V1 | DZ-260 A-V2 | DZ-260 A-V3 | DZ-260 S-V1 | DZ-260 S-V2 | DZ-260 S-V3 |
|---|---|---|---|---|---|---|
| Seal Length | 260mm | 260mm | 260mm | 260mm | 260mm | 260mm |
| Chamber Dimensions | 330×270×50mm | 330×270×50mm | ||||
| Vacuum Pump Type | Oil Pump | Oil Pump | Oil Pump | Oil Pump | Oil Pump | Oil Pump |
| Pumping Speed of Vacuum Pump | 6.5m³/h | 6.5m³/h | 6.5m³/h | 4.2m³/h | 4.2m³/h | 4.2m³/h |
| Voltage | AC 120V 60Hz | AC 230V 50Hz | AC 230V 50Hz | AC 120V 60Hz | AC 230V 50Hz | AC 230V 50Hz |
| Max. Power | 1000W | 1000W | 1000W | 1000W | 1000W | 1000W |
| Vacuum Pump Power | 180W | 180W | 180W | 120W | 120W | 120W |
| Machine Material | 201 Stainless Steel | 201 Stainless Steel | ||||
STRUCTURE DIAGRAM
Diagram shows two views of the vacuum packing machine.
View 1: Front and side perspective of the machine with the lid open.
View 2: Rear and side perspective of the machine.
| Part Number | Description |
|---|---|
| 1 | Vacuum cover |
| 2 | Silicone strip |
| 3 | Vacuum sealing bar |
| 4 | Base plate |
| 5 | Bag pressing rod |
| 6 | Sealing heating strip |
| 7 | Indicator |
| 8 | Vacuum gauge |
| 9 | Power switch |
| 10 | Power plug |
| 11 | Circuit board |
| 12 | Vacuum pump solenoid valve |
| 13 | Heating transformer |
| 14 | Rear cover screw hole |
| 15 | Vacuum pump |
| 16 | Oil injection port |
| 17 | Oil level observation window |
| 18 | Oil drain screw |
PARTS LIST
| Parts | DZ-260 A-V1 | DZ-260 A-V2 | DZ-260 A-V3 | DZ-260 S-V1 | DZ-260 S-V2 | DZ-260 S-V3 |
|---|---|---|---|---|---|---|
| Heating Wire | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
| Teflon Cloth | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
| Filler Board | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
| Vacuum Pump Oil | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
| Allen Key | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
| Vacuum Bag | ×30 | ×30 | ×30 | ×30 | ×30 | ×30 |
| Chamber Sealing Strip | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
| Power Cord | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
| Fuse | ×2 | ×2 | ×2 | ×2 | ×2 | ×2 |
| User Manual | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
OPERATING INSTRUCTIONS
1. Oil Filling Procedure:
- Unscrew back cover screw and lift back cover.
- Take out the oil mist filter.
- Add vacuum pump oil.
- Oil level should be between 1/2 and 3/4 of the observation hole (do not overfill).
- After adding oil, screw back the oil mist filter and close the back cover.
It is strictly prohibited to start the vacuum pump without oil.
2. PANEL USAGE INSTRUCTIONS:
- Step 1: Connect the matching power supply.
- Step 2: Open POWER SWITCH.
- Step 3: VACUUM - Click the SETTING button on the control panel to select the target setting. Use the RAISE or LOWER buttons to set the ideal vacuum time (typically 30-40 seconds).
- Step 4: SEALING - Click the SETTING button twice. The sealing time is typically set to 1.5-2 seconds, adjusted according to the thickness of the vacuum bag. It is strictly prohibited to set the sealing time too long, as it may burn out the sealing heating strip.
- Step 5: COOLING - After setting the sealing time, click the SETTING button again to set the cooling time (usually 3-5 seconds). After setting the cooling time, click the SETTING button; the control panel will display the letter ED, indicating the end of the setting process.
Control Panel Description: Features a VACUUM METER displaying pressure in MPa, and buttons for STOP (1), SETTING (2), RAISE (3), LOWER (4), START (5). Also indicates VACUUM (6), SEALING (7), and COOLING (8) indicators.
3. Oil Change:
When the machine needs oil change or is not used for a long time, loosen the screw under the oil window and drain the vacuum pump oil. It is suggested to replace the vacuum pump oil after the machine has been working continuously for 800 hours.
CIRCUIT DIAGRAM
The circuit diagram illustrates the electrical connections for the 110V/220VAC power supply, switch, electromagnetism valve, transformer, and vacuum pumps.
MAINTENANCE
- After use, clean the machine surface and remove residual materials inside.
- When storing, keep the machine in a clean, dry, and safe location away from children.
- All maintenance, service, and repairs not discussed in this manual should only be performed by qualified service technicians.
Replacing Components:
Replace the high temperature cloth (Teflon Cloth):
- Remove the screws on both sides of the tray, then pick up the whole tray.
- Remove the upper screws.
- Remove the old high-temperature cloth.
- Apply new high-temperature cloth.
- Reinstall the original screws.
- Complete the installation.
Replace the Chamber Sealing Strip:
- Remove the Chamber Sealing Strip.
- Replace the Chamber Sealing Strip with a new one.
- Complete the installation.
If the fuse is damaged, replace it as shown:
- Find the power outlet on the back.
- Take out the slot.
- The fuse is in the groove of the card slot.
- Take out a fuse.
TROUBLESHOOTING AND SOLUTIONS
| Problem | Possible Cause | Solution |
|---|---|---|
| The machine doesn't work and the control panel shows nothing. | 1. No connection of the power supply. 2. The contact of the power switch is loose. | 1. Check whether the plug and socket are effectively connected. 2. Check whether the wiring of the power input part inside the machine is loose or detached. |
| The control panel starts up, but the machine doesn't work. | The parameter is being set. | Complete the parameter setting. |
| The best vacuum state can't be achieved. The vacuumizing speed is slow. | 1. Short vacuumizing time. 2. The oil in the vacuum pump is not enough or the oil is not clean. 3. Air leakage and wear of the sealing ring. | 1. Extend the vacuum time. 2. Check the oil level, refuel or change the oil (pay attention to the oil type (vacuum oil 46#, 68#) and oil quantity). 3. Replace the sealing ring. |
| Sealing failure or poor sealing. | 1. The bags are not correctly placed on the heating plates. 2. Too long/short sealing time. 3. Inappropriate heating temperature. 4. Silicon strip damaged or with impurity. 5. Damage of electric heating wire. | 1. Place the bags on the plate in order. 2. Shorten/prolong the sealing time. 3. Choose proper temperature. 4. Clean or replace the silicon rubber. 5. Change electric heating wire. |
CORRECT DISPOSAL
This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices.
Manufacturer:
Shanghaimuxinmuyeyouxiangongsi
Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi, Shanghai
EC REP:
SHUNSHUN GmbH.
Römeräcker 9 Z2021, 76351 Linkenheim-Hochstetten, Germany
Tel: +49 1727041930
Email: euvertreter@gmail.com
UK REP:
Pooledas Group Ltd.
Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom
Tel: 01772418127
Email: pooledas123@gmail.com
Imported to AUS:
SIHAO PTY LTD.
1 ROKEVA STREET EASTWOOD NSW 2122 Australia
Imported to USA:
Sanven Technology Ltd.
Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
Made In China
