Introduction
This document is the user manual for VEVOR Vacuum Packing Machines. It provides essential information for safe operation, maintenance, and troubleshooting. Please read all instructions carefully before operating the machine.
VEVOR is committed to providing tools with competitive prices. The terms "Save Half" or "Half Price" represent an estimate of potential savings compared to major top brands and may not apply to all product categories. Customers are advised to verify savings carefully when placing an order.
Product Overview
The VEVOR Vacuum Packing Machine is designed for efficient vacuum sealing of various items. It is available in the following models:
- DZ-260A-V1, DZ-260A-V2, DZ-260A-V3
- DZ-260S-V1, DZ-260S-V2, DZ-260S-V3
For product questions or technical support, please contact:
Technical Support and E-Warranty Certificate
www.vevor.com/support
This is the original instruction manual. VEVOR reserves the right to interpret its content. Product appearance may vary. VEVOR may update technology or software without prior notice.
▲WARNING: Assembly and Operation Instructions
- Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating.
- Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
General Safety Rules
- Read the entire operating instructions before using the product for the first time.
- The guarantee/warranty will be void if damage is incurred due to non-compliance with operating instructions. Liability for consequential damage is excluded.
- VEVOR assumes no liability for damage to property or personal injury caused by improper use or failure to observe safety instructions.
- Unauthorized conversion, modification, or disassembly of the products is inadmissible due to safety and approval reasons (CE).
- The product is not a toy and must be kept out of the reach of children. Exercise particular care if children are present.
- The product must not get damp or wet; it is intended for for use in dry, indoor locations only (not bathrooms or similarly damp areas). There is a risk of fatal electric shock.
- Do not expose the product or its accessories to damp or extremely high or low temperatures.
- Do not leave packing materials unattended, as they may become dangerous playing material for children.
- Dropping, falling, excessive pressure, or tensile forces could destroy or limit the function of the product.
- Never position the device near combustible or easily inflammable materials.
- Always ensure the object is placed in the center of the housing on the rotary table.
Product Applications
This machine uses plastic film or plastic aluminum film to vacuum package paste foods, fruits, sauce vegetables, chemicals, pharmaceuticals, electronic components, precision instruments, rare metals, and other items. Products packaged under vacuum are not easily oxidized or moldy, making it especially suitable for industries such as tea, food, and medicine.
If you suspect safe operation is no longer possible (e.g., visible damage, device not functioning, after long storage, or after heavy transportation stress), disconnect the device immediately and secure it against inadvertent operation.
SAVE THESE INSTRUCTIONS
Model and Parameters
| Model | DZ-260A-V1 | DZ-260A-V2 | DZ-260A-V3 | DZ-260S-V1 | DZ-260S-V2 | DZ-260S-V3 |
|---|---|---|---|---|---|---|
| Seal Length | 260mm | 260mm | 260mm | 260mm | 260mm | 260mm |
| Chamber Dimensions | 330×270×50mm | 330×270×50mm | ||||
| Vacuum Pump Type | Oil Pump | Oil Pump | Oil Pump | Oil Pump | Oil Pump | Oil Pump |
| Pumping Speed of Vacuum Pump | 6.5m³/h | 6.5m³/h | 6.5m³/h | 4.2m³/h | 4.2m³/h | 4.2m³/h |
| Voltage | AC 120V 60Hz | AC 230V 50Hz | AC 230V 50Hz | AC 120V 60Hz | AC 230V 50Hz | AC 230V 50Hz |
| Max. Power | 950W | 950W | 950W | 950W | 950W | 950W |
| Vacuum Pump Power | 180W | 180W | 180W | 120W | 120W | 120W |
| Machine Material | 201 Stainless Steel | 201 Stainless Steel | ||||
Structure Diagram
- Vacuum cover
- Silicone strip
- Vacuum sealing bar
- Base plate
- Bag pressing rod
- Sealing heating strip
- Indicator
- Vacuum gauge
- Power switch
- Power plug
- Circuit board
- Vacuum pump solenoid valve
- Heating transformer
- Rear cover screw hole
- Vacuum pump
- Oil injection port
- Oil level observation window
- Oil drain screw
Parts List
| Parts | DZ-260A-V1 | DZ-260A-V2 | DZ-260A-V3 | DZ-260S-V1 | DZ-260S-V2 | DZ-260S-V3 |
|---|---|---|---|---|---|---|
| Heating Wire | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
| Teflon Cloth | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
| Filler Board | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
| Vacuum Pump Oil | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
| Allen Key | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
| Vacuum Bag | ×30 | ×30 | ×30 | ×30 | ×30 | ×30 |
| Chamber Sealing Strip | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
| Power Cord | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
| Fuse | ×2 | ×2 | ×2 | ×2 | ×2 | ×2 |
| User Manual | ×1 | ×1 | ×1 | ×1 | ×1 | ×1 |
Operating Instructions
1. Oil Filling Procedure
- Unscrew the back cover screw and lift the back cover.
- Take out the oil mist filter.
- Add vacuum pump oil.
- Ensure the oil level is between 1/2 and 3/4 of the observation hole (do not overfill).
- After adding oil, screw back the oil mist filter and close the back cover.
It is strictly prohibited to start the vacuum pump without oil.
2. Panel Usage Instructions
- Step 1: Connect the matching power supply.
- Step 2: Open POWER SWITCH.
- Step 3: VACUUM: Click the SETTING button on the control panel, select the target setting. Use the RAISE or LOWER button to set the ideal vacuum time (generally 30-40 seconds).
- Step 4: SEALING: Click the SETTING button twice. The sealing time is generally set to 1.5-2 seconds. Adjust sealing time according to the thickness of the vacuum bag.
It is strictly prohibited to set the sealing time too long, as it may burn out the sealing heating strip.
3. Cooling Setting
Step 5: COOLING: After setting the sealing time, click the SETTING button again to set the cooling time, usually 3-5 seconds. After setting the cooling time, click the SETTING button, and the control panel will display the letter "ED", indicating the end of the setting process.
4. Oil Change and Long-Term Storage
When the machine needs an oil change or is not used for a long time, loosen the screw under the oil window and drain the vacuum pump oil. It is suggested to replace the vacuum pump oil after the machine has been working continuously for 800 hours.
Circuit Diagram
Maintenance
- After use, clean the surface of the machine and remove any residual materials inside.
- When storing, keep the machine in a clean, dry, and safe location away from children.
- All maintenance, service, and repairs not discussed in this manual should only be performed by qualified service technicians.
Replacing the High Temperature Cloth (Teflon Cloth)
- Step 1: Remove the screws on both sides of the tray, then lift up the whole tray.
- Step 2: Remove the upper screws securing the sealing bar.
- Step 3: Remove the old high-temperature cloth.
- Step 4: Apply the new high-temperature cloth.
- Step 5: Reinstall the original screws.
- Step 6: Completing the Installation.
Replacing the Chamber Sealing Strip
- Step 1: Remove the Chamber Sealing Strip.
- Step 2: Replace the Chamber Sealing Strip with a new one.
- Step 3: Completing the Installation.
Replacing the Fuse
If the fuse is damaged, replace it as shown:
- Step 1: Find the power outlet on the back of the machine.
- Step 2: Take out the fuse slot.
- Step 3: The fuse is located in the groove of the card slot.
- Step 4: Take out the old fuse and insert a new one.
Troubleshooting and Solutions
| Problem | Possible Cause | Solution |
|---|---|---|
| The machine doesn't work and the control panel shows nothing. | 1. No connection of the power supply. 2. The contact of the power switch is loose. | 1. Check whether the plug and socket are effectively connected. 2. Check whether the wiring of the power input part inside the machine is loose or detached. |
| The control panel starts, but the machine doesn't work. | The parameter is being set. | Complete the parameter setting. |
| The best vacuum state can't be achieved. The vacuumizing speed is slow. | 1. Short vacuumizing time. 2. The oil in the vacuum pump is not enough or the oil is not clean. 3. Air leakage and wear of the sealing ring. | 1. Extend the vacuum time. 2. Check the oil level, refuel or change the oil (pay attention to the oil type: vacuum oil 46#, 68# and oil quantity). 3. Replace the sealing ring. |
| Sealing failure or poor sealing. | 1. The bags are not correctly placed on the heating plates. 2. Too long/short sealing time. 3. Inappropriate heating temperature. 4. Silicon strip damaged or with impurity. 5. Damage of electric heating wire. | 1. Place the bags on the plate in order. 2. Shorten/prolong the sealing time. 3. Choose proper temperature. 4. Clean or replace the silicon rubber. 5. Change electric heating wire. |
Correct Disposal
This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through ?️ indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste but must be taken to a collection point for recycling electrical and electronic devices.
Manufacturer and Representatives
Manufacturer: Shanghaimuxinmuyeyouxiangongsi
Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi, Shanghai
EC REP: SHUNSHUN GmbH.
Römeräcker 9 Z2021, 76351 Linkenheim-Hochstetten, Germany
Tel: +49 1727041930
Email: euvertreter@gmail.com
UK REP: Pooledas Group Ltd.
Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom
Tel: 01772418127
Email: pooledas123@gmail.com
Imported to AUS: SIHAO PTY LTD.
1 ROKEVA STREETEASTWOOD NSW 2122 Australia
Imported to USA: Sanven Technology Ltd.
Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
Made In China
Contact Us â Official VEVOR Support
