Baby Trend PY47 Nursery Center Instruction Manual

Parts List

Before assembling, verify you have all the parts for this model:

• Item #1: Playard (fully assembled), Mattress, Bassinet with metal support tubes, Napper, Changing Table
• Item #2: Long Curved Bar, Short Bar with Connector Knob
• Item #1: Music Center
• Item #1: Travel / Storage Bag
• Item #1: Parent Organizer

Note: Toys and mobile may vary.

Important Safety Warnings

Suffocation Hazards

• WARNING: NEVER LEAVE INFANT IN PRODUCT WITH SIDES DOWN. Infant may roll into space between pad and loose mesh side, causing suffocation.
• Infants can suffocate in gaps between a mattress that is too small or too thick and product sides, or on soft bedding.
• Never add a mattress, pillow, comforter, or padding. Use only the mattress provided by the manufacturer. Never use a water mattress with this product.
• NEVER use plastic shipping bags or other plastic film as mattress covers not sold and intended for that purpose, as they can cause suffocation.

Fall Hazards

• Discontinue use of the product when the child is able to climb out or has reached a height of 35 in. (890 mm) or weighs 30 lbs. (13.6 kgs), whichever comes first.
• When the child is able to pull to standing position, remove bumper pads, large toys, and other objects that could serve as steps for climbing out.
• NEVER place product near a window where cords from blinds or drapes can strangle a child.
• Always ensure the bassinet is securely locked on the base/stand by pulling upwards on the bassinet bed.

Strangulation Hazards

• Strings can cause strangulation! NEVER place items with a string around a child's neck, such as hood strings or pacifier cords. NEVER suspend strings over the playard or attach strings to toys.
• NEVER leave the changing table in place when the child is in the bassinet or playard. Always flip the changing table down when not in use.

General Safety & Use

• Always provide supervision necessary for the continued safety of your child. When used for playing, NEVER leave child unattended.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless otherwise advised by your physician.
• Child can become entrapped and die when improvised netting or covers are placed on top of a play yard. Never add such items to confine a child in the play yard.
• NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact Baby Trend Customer Service at 1-800-328-7363 for replacement parts, repair, or instructions. NEVER substitute parts.
• NEVER leave child in product with sides lowered. Be sure sides are in raised and locked position whenever child is in product.
• This product is not intended for commercial use.
• If a sheet is used with the pad, use only the one provided by the bassinet or cradle manufacturer or one specifically designed to fit the dimensions of the bassinet or cradle mattress.

Assembly Instructions: Playard

Adult assembly is required.

1. Unzip the bag and remove the Playard frame. Undo the fasten straps and set the mattress aside. Do not push the center down yet.
2. Ensure all four (4) top rails are fully erected before lowering the center. Pull up one rail at a time, holding each side, and pull sharply upwards. Ensure both tubes latch in place and each rail is rigid. The center must be raised while locking the rails. If one rail locks but the other does not, unlock the rail by squeezing the release in the center and try again.
3. Once all four top rails are locked, push down on the center handle. The center mechanism automatically locks. Test each top rail by pushing down slightly to confirm it is rigid and securely in place before use.
4. Place the Mattress on the floor of the Playard with the padded side facing up.
5. Insert the hook & loop fasteners located on the underside of the Mattress through the slots in the floor of each end of the Playard. Fasten the hook and loop fasteners to the underside of the Playard floor to prevent the Mattress from moving.

Folding the Playard

1. Release the hook and loop fasteners holding the Mattress from underneath the Playard floor or the Bassinet and set the mattress aside.
2. Do not unlock top rails yet; the center of the floor must be raised before top rails will unlock.
3. Raise the center as high as the top rails. Gather the Legs and Wheels together towards the center as close as possible so they nearly touch.
4. Locate the rail latch release in the center and bottom side of each rail. Squeeze the lever with two hands until the rail releases the two tubes, then push down. Note: If the top rail(s) do not release completely, DO NOT FORCE! Lift the center of the floor higher. Both tubes must be released for the top rail to fold.
5. Gather four corners and center tightly. Wrap the Mattress around the Playard frame with the padded side facing inward.
6. Secure the hook and loop fasteners by feeding them through the loops on the end of the Mattress and folding them back onto themselves.
7. Place the folded Playard into the carry bag so that the handle comes through the opening between each side of the zipper.

Assembly: Bassinet

Ensure the Playard is fully assembled and securely locked before installing or using the bassinet feature.

1. Connect opposing Mattress Support Tubes that are attached to the bottom of the Bassinet. Ensure the tubes are connected as shown.
2. Position the Bassinet over and down into the fully assembled Playard. Secure in place by pushing down firmly on each plastic support clip until all are snapped into place.
3. Place the Mattress into the Bassinet with the padded side facing upward. Fasten tabs underneath the Mattress to secure it in place.

To Remove Bassinet: Remove Mattress from Bassinet. Remove Canopy. Disconnect opposing Mattress Support Tubes. Unsnap all clips and lift Bassinet.

Assembly: Changing Table

Ensure the Playard is fully assembled and securely locked before installing or using the changing table feature. Refer to the Playard assembly section.

1. Connect the two (2) Long Curved Bars together.
2. Insert the assembled curved bars into the Changing Table fabric. Slide the bars around inside the sleeve of the Changing Table.
3. Connect the two (2) Short Bars to each end of the Long Curved Bar. Make sure that the knobs are both facing down and in the same direction on each end.
4. Insert Connector Knob Prongs into holes located on both corners of the Playard. Turn the Connector Knobs counter-clockwise to lock into place.
5. Flip the Changing Table over onto the Playard. Snap the two (2) buttons on the flap down onto the Playard.
6. Locate the hook and loop fasteners on the bottom of the changing table and on the inside of the side rails of the playard.
7. Flip the changing table into its upper position.
8. Secure the changing table to the playard frame by fastening the hook and loop fasteners on the underside of the changing table to the side rails of the playard frame.
9. Restraint System: Place child on changing table, ensure hand and arms are clear of the restraint. Bring the restraint around the child's waist and clip the male and female ends of the buckle together. Tighten strap until it fits snugly around the child's waist. DO NOT OVER TIGHTEN. To remove, unsnap the buckle.

To Remove Changing Table: Flip Changing Table to the outside of the Playard. Unsnap fabric flap of Changing Table from Playard. Twist Connector Knobs clockwise to unlock. Remove Changing Table from Playard and disconnect the Short Bars from the Curved Bar by pressing on the snap buttons and pulling apart. Remove Curved Bar from Changing Table sleeve.

Assembly: Parent Organizer / Diaper Stacker

1. Parent Organizer: Position each hook so that the hooked end is facing the rear side of the organizer. Press the hook down firmly into the slot until it snaps into place.
2. Connect the Parent Organizer/Diaper Stacker to the Playard by sliding the two (2) connecting clips over an open portion of the top rail of the Playard.

Note: The Parent Organizer/Diaper Stacker can only be installed on open sides of the Playard where the connecting clips can easily be attached without interfering with other features.

Assembly: Napper

Ensure the Playard is fully assembled and securely locked before installing or using the Napper feature. Refer to the Playard assembly section.

1. Pull napper fabric back to access the bottom of the napper. Use the handles to pull the frame supports into the support locks. Ensure the frame supports click and are seated firmly in the support locks.
2. Pull the fabric over the frame and secure fabric with buttons on the sides and front of the frame.
3. Use the hook and loop fasteners provided to fix the mattress into the Napper.
4. Raise the handle on the Napper by pulling up on the handle. Make sure the handle clicks into position before using. To lower the handle, open both locks on the base of the handle by pulling locks upwards with your fingers while pushing the handle backwards.
5. To use the Napper in the Playard, lower the Napper into the bassinet. Push down on the front and rear of the Napper to secure the hooks onto the Playard railing. Button the front and rear strap from the napper onto the playard frame.
6. Rocker Function: Turn Napper over and pull rocker feet from the base of the Napper. Set the napper on a flat surface. NEVER use the Napper on a raised surface such as a Table, Bed, or Chair, as a fall can occur.

Operation: Music Center

WARNING: Keep batteries out of children's reach. Old and new batteries should not be mixed. Alkaline, standard carbon-zinc, and rechargeable nickel-cadmium batteries should not be mixed. Remove batteries before storing the music center for a long period of time.

The Music Center requires 4 AA batteries. Please see figure 29 for battery installation. Unscrew the battery door screws and pull outward on the battery door. Install batteries as shown. Re-install battery door and secure with screws.

• To listen to MUSIC: Press the MUSIC button. Press the button to change the song.
• To listen to NATURE sounds: Press the NATURE button. Press the button to change the sound.

Volume Control: Two buttons control the unit's volume.

VIBRATION: To use the VIBRATION, press the VIBRATION button once to activate the speed, press again for faster speed, and press again to reduce the speed.

NIGHT LIGHT: To use the night light, press the NIGHT LIGHT button.

Maintenance and Cleaning Instructions

• Use only household mild soap and warm water.
• DO NOT USE BLEACH.
• DO NOT MACHINE WASH.

Customer Service

If you experience any difficulty with assembly, missing parts, or use, please DO NOT return this item to the store. Retail stores are unable to properly assist you. Contact our Customer Service Department directly for assistance.

Call toll-free: 1-800-328-7363 (Monday - Friday, between the hours of 8:00 a.m. and 4:30 p.m. PST).

Regulatory Information

FCC Statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Canada ICES-003 Statement

This Class B digital apparatus complies with Industry Canada Standard ICES-003. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.