BRIMNES Wardrobe

Safety Warnings

Furniture Tipover Warning

Children have died from furniture tipover. To reduce the risk of furniture tipover:

• ⚠️ ALWAYS install tipover restraint provided.
• ❌ NEVER put a TV on this product.
• ❌ NEVER allow children to stand, climb or hang on drawers, doors, or shelves.
• ❌ NEVER open more than one drawer at a time.
• Place heaviest items in the lowest drawers.

Tools and Hardware

Required Tools

• Screwdrivers (Phillips and Flathead)
• Hammer
• Ladder
• Drill
• Drill bits: Ø 5/16" (8 mm), Ø 1/8" (3 mm)

Included Hardware

• 109574: Screw (x2)
• 10087223: Wall Plug (x2)
• 109049: Screw (x2)
• 100823: Washer (x4)
• 106989: Bracket (x2)
• 370766: Bracket (x2)
• 10038685: Bracket (x2)
• 100001: Handle (x2)
• 101206: Nail (x75)
• 105494: Plastic Cover (x34)
• 123840: Cam Bolt (x4)
• 109837: Cam Bolt (x4)
• 10121196: Cam Bolt (x4)
• 100214: Screw (x2)
• 106940: Rod (x2)
• 118331: Cam Lock (x16)
• 109567: Screw (x8)
• 101345: Wooden Dowel (x27 + 4x = 31x)
• 119250: Cam Lock Nut (x20)
• 119251: Cam Lock Nut (x20)
• 119252: Cam Lock Nut (x20)
• 105248: Screw (x8 + 2x + 6x + 1x = 17x)
• 153548: Handle (x3 + 4x = 7x)
• 158568: Handle (x3 + 4x = 7x)
• 107091: Cover Cap (x1 + 2x = 3x)
• 101532: Plastic Dowel (x4)
• 157306: Hinge Part (x2)
• 157307: Hinge Part (x2)
• 10121089: Hinge Part (x2)
• 109336: Hinge Part (x6)
• 109220: Bracket (x6)
• 122663: Shelf Support (x2)
• 119543: Shelf Support (x2)
• 10121128: Shelf Support (x2)
• 124328: Shelf Support (x2)
• 128763: Shelf Support (x2)
• 145915: Shelf Support (x2)
• 10121200: Shelf Support (x2)

Assembly Steps

Step 1

Attach two brackets (109220) to the bottom panel using three screws (105248) for each bracket. Ensure the brackets are oriented correctly.

Step 2

Insert ten cam locks (118331) into the designated holes on the two long side panels. Use a screwdriver to turn the cam locks to the open position.

Step 3

Insert four wooden dowels (101345) into the corresponding holes on one of the long side panels.

Step 4

Attach the top panel to the side panel by aligning the dowels and holes. Slide the panel into place.

Step 5

Insert two cam lock nuts (119250, 119251, 119252) into the holes on the top panel. Insert the cam bolts and tighten them with a screwdriver. [rotate to lock]

Step 6

Insert nine wooden dowels (101345) into the designated holes on two panels.

Step 7

Attach two cam lock nuts (119250, 119251, 119252) to the panels. Insert the cam bolts and tighten.

Step 8

Attach the rod (106940) to the panel using two screws (105248).

Step 9

Attach the panel using two cam lock nuts (119250, 119251, 119252). Insert the cam bolts and tighten.

Step 10

Slide two panels into place, aligning them with the corresponding slots.

Step 11

Attach two cam lock nuts (119250, 119251, 119252). Insert the cam bolts and tighten.

Step 12

Slide the bottom panel into place, aligning it with the slots. [insert here]

Step 13

Insert eight wooden dowels (101345) into the designated holes on two panels.

Step 14

Slide the panel into place, aligning it with the slots. [insert here]

Step 15

Attach the rod (100001) to the panel using two screws (100214). [tighten screw]

Step 16

Insert two cam locks (118331) into the designated holes on the panel. Insert the screws and tighten.

Step 17

Slide the panel into place, aligning it with the slots. [insert here]

Step 18

Attach two cam lock nuts (119250, 119251, 119252). Insert the cam bolts and tighten.

Step 19

Attach two brackets (10038685) to the long bar using two screws (105248) for each bracket. [tighten screw]

Step 20

Attach two handles (158548, 158568) to the long bar using two screws for each handle. [tighten screw]

Step 21

Attach one bracket (10038685) to the panel using two screws (105248). [tighten screw]

Step 22

Slide the panel into place. [insert here]

Step 23

Attach two cam lock nuts (119250, 119251, 119252). Insert the cam bolts and tighten.

Step 24

Insert two wooden dowels (101345) into the designated holes on the panel.

Step 25

Slide the panel into place. [insert here]

Step 26

Attach six cam lock nuts (119250, 119251, 119252). Insert the cam bolts and tighten. [rotate to lock]

Step 27

Attach one bracket (10038685) to the panel using two screws (105248). [tighten screw]

Step 28

Attach two dowels (123840, 109837, 10121196) to the panel. Use a hammer to gently tap them in. [hammer nail]

Step 29

Insert four cam locks (118331) into the designated holes on the panel. Insert the screws and tighten.

Step 30

Insert four wooden dowels (101345) into the designated holes on the panel.

Step 31

Slide the panel into place. [insert here]

Step 32

Attach four cam lock nuts (119250, 119251, 119252). Insert the cam bolts and tighten.

Step 33

Attach four brackets (153548, 158568) to the panel using a hammer to tap in the nails (101206).

Step 34

Attach the panel by sliding it into place. [slide into place]

Step 35

Attach one plastic cover (105494) using one nail (101206). [hammer nail]

Step 36

Attach one plastic cover (105494) using one nail (101206). [hammer nail]

Step 37

Mark the center line on the panel. Insert one nail (101206) at the marked position.

Step 38

Insert four nails (101206) into the designated holes.

Step 39

Attach thirty-three plastic covers (105494) using thirty-three nails (101206). [hammer nail]

Step 40

Attach two brackets (106989) to the unit using two screws (100823) and two screws (109049) for each bracket. [tighten screw]

Step 41

Attach two brackets (106989) to the top of the wardrobe. Use a screwdriver to tighten the screws. [tighten screw]

Step 42

Position the wardrobe. The 'X' marks indicate the final placement area.

Step 43

Wall mounting instructions. Refer to the wall type (A, B, or C) for appropriate hardware. Ensure the unit is securely fastened to the wall to prevent tipover. [weight limit]

Step 44

Attach two brackets (106989) to the top of the wardrobe using two screws (100823) and two screws (109574) for each bracket. [tighten screw]

Step 45

Attach two hinge parts (157306, 157307, 10121089) to the wardrobe. Use screws (105248) and tighten. [tighten screw]

Step 46

Insert four plastic dowels (101532) into the designated holes on the shelf supports.

Step 47

Attach six hinge parts (109336) to the wardrobe. Use screws (105248) and tighten. [tighten screw]

Step 48

Attach the doors by aligning the hinges. Use screws (105248) and tighten. [tighten screw]

Step 49

Attach four screws (109567) to the door frame. Insert two shelf supports (124328, 128763, 145915, 10121200) into the designated holes.

Step 50

Attach two cover caps (107091) to the designated holes.

Wall Mounting Instructions

Wall Types and Hardware

The supplied screws and plugs can be used with most solid (A) and hollow (B) walls. For solid wood (C), use the screws without plugs. If you are uncertain, seek professional advice.

Type A: Solid Wall

Use screws (Ø 5/16" (8 mm)) without plugs.

Type B: Hollow Wall

Use screws (Ø 5/16" (8 mm)) with plugs (10087223).

Type C: Solid Wood

Use screws (Ø 1/8" (3 mm)) without plugs.

Mounting Procedure

Follow the diagrams to drill holes of the correct size (e.g., 2 3/4" (70 mm) for solid walls, ≈ 1 1/4" (30 mm) for hollow walls) and attach the anti-tip hardware to the wall and the furniture. Ensure the unit is securely fastened to the wall to prevent tipover. [weight limit]