BUSLÄTT Chair Assembly Instructions

Product: BUSLÄTT Chair

Brand: IKEA

Document Reference: AA-2548069-2

Product Overview

This document provides detailed instructions for assembling the IKEA BUSLÄTT chair. Please follow each step carefully to ensure correct assembly and safe use of the product.

Visual: The document cover displays the product name 'BUSLÄTT' prominently, followed by the IKEA logo and the text 'Design and Quality IKEA of Sweden'.

Parts and Tools Required

Before starting, verify that all parts and tools listed below are present.

Parts List:

130718: Bolt (4x)
10126011: Bolt (4x)
106917: Screw (4x)
100092: Allen Key (1x)

Tools Required:

Screwdriver [?️] (not included)

Important Safety Notes:

Do not use power tools for assembly [❌?️].
Handle all parts with care to avoid damage [✅].
If you are unsure about any step, seek assistance.

Visual: Page 2 shows the required parts and tools. It includes the four types of fasteners and the Allen key. Icons indicate a screwdriver is needed, warn against power drills, and suggest careful handling.

Assembly Steps

Step 1: Attach Backrest

Insert the chair backrest into the designated slots on the chair's side supports.

Visual: A diagram shows a person inserting the backrest into the top of the chair's side supports, with an arrow indicating the direction of insertion.

Step 2: Secure Backrest

Fasten the backrest using four screws (106917). Insert the screws through the pre-drilled holes on the outside of the side supports into the backrest.

Visual: A close-up view shows four screws being inserted from the outside of the chair's side supports into the backrest. Icons indicate a correctly seated screw and an incorrectly seated screw (protruding).

Step 3: Position Seat Support Bar

Place the seat support bar between the front and rear legs of the chair frame. Align the holes on the bar with the corresponding holes on the legs.

Visual: A diagram illustrates the seat support bar being positioned between the chair legs, with arrows indicating placement. Close-up views show the alignment of holes on the bar and legs.

Step 4: Secure Seat Support Bar

Attach the seat support bar using four bolts (130718). Insert the bolts through the legs into the support bar and tighten them using the Allen key (100092).

Visual: A close-up shows a bolt (130718) being inserted through a chair leg into the support bar and tightened with the Allen key (100092). An icon highlights the correct bolt for this step (130718) and an incorrect bolt (10126011).

Step 5: Attach Seat

Place the seat onto the chair frame, aligning it with the support bar and legs. Secure the seat using four bolts (10126011).

Visual: The chair is shown in an inverted position. Four bolts (10126011) are depicted being inserted through the seat frame into the chair legs. The Allen key is implied for tightening.

Step 6: Final Screw Tightening

Ensure all screws (106917) used in previous steps are securely tightened.

Visual: The chair is shown with arrows pointing to the locations where screws were previously inserted. Close-up views illustrate correct and incorrect screw tightening.

Step 7: Final Bolt Tightening

Ensure all bolts (130718 and 10126011) are securely tightened using the Allen key (100092).

Visual: The chair is shown with arrows pointing to the locations where bolts were previously inserted. Close-up views illustrate correct and incorrect bolt tightening.

Important Information and Care

Stability: After assembly, check that the chair is stable and does not wobble. Do not push or lean on the chair in a manner that could cause it to tip over [⚠️].

Visual: A diagram shows a chair wobbling and a hand pushing it, with a prohibition symbol over the action, indicating it should not be pushed forcefully. Another diagram shows a stable chair.

Care: For cleaning and maintenance, please refer to IKEA's general care instructions for furniture.

Manufacturer Information:

Inter IKEA Systems B.V. 2024

Date of Publication: 2025-01-10