Fischer FIS V Plus Injection Mortar

High-performance chemical injection mortar for anchoring applications.

Product Overview and Applications

The Fischer FIS V Plus is a versatile, two-component injection mortar designed for high-performance anchoring in concrete and masonry. It is suitable for a wide range of applications, including structural connections, facade fixings, and heavy-duty anchoring.

Key applications include:

Option 1 for cracked concrete
Option 7 for non-cracked concrete
Post-installed rebar connections
Masonry use (categories b, c, or d)

Certifications and Approvals

The FIS V Plus system holds significant certifications, ensuring its reliability and suitability for demanding applications:

ETA-20/0603: Option 1 for cracked concrete, Option 7 for non-cracked concrete.
ETA-20/0728: Post-installed rebar connection.
ETA-20/0729: Masonry use categories b, c or d.
aBG Approvals: Z-21.3-1737, Z-21.8-1837, Z-21.8-1954, Z-21.8-2029.
ICC-ES Evaluation Report: ESR-2786 (available at www.icc-es.org).

Emissions Information: The product contributes to good indoor air quality, indicated by an A+ rating (very low emissions) on the French VOC label.

Substrate Conditions

The performance of the anchor system depends on the condition of the base material. The FIS V Plus is suitable for various concrete conditions:

Condition	Description
Dry Concrete	Standard concrete condition.
Water Saturated Concrete	Concrete with high moisture content.
Contaminated Drill Hole	Drill hole containing dust or debris. Proper cleaning is crucial.
Water Filled Borehole	Drill hole containing standing water. Water must be removed before installation.

Technical Data: Processing and Curing Times

Working and curing times vary based on ambient and substrate temperature. The following table provides guidelines:

Temperature Range (°C / °F)	Working Time / Processing Time	Curing Time
-5 to 0 °C / +23 to +32 °F	-	24 h
> 0 to +5 °C / +32 to +41 °F	13 min	180 min
> +5 to +10 °C / +41 to +50 °F	9 min	90 min
> +10 to +20 °C / +50 to +68 °F	5 min	60 min
> +20 to +30 °C / +68 to +86 °F	4 min	45 min
> +30 to +40 °C / +86 to +104 °F	2 min	36 min

Storage Temperature: +5 °C to +25 °C / +41 °F to +77 °F.

Product Variants and Specifications

The FIS V Plus system is available in various product variants and sizes, each with specific technical specifications and approvals. Below are key specifications for common variants.

FIS A / RG M

M	M6	M8	M10	M12	M16	M20	M24	M27	M30
ETA-20/0603, Option 1	✓	✓	✓	✓	✓	✓	✓	✓	✓
ETA-20/0603, Option 7	✓	✓	✓	✓	✓	✓	✓	✓	✓
d₀ [mm]	8	10	12	14	18	24	28	30	35
h_0,min [mm]	50	60	60	70	80	90	96	108	120
h_0,max [mm]	72	160	200	240	320	400	480	540	600
fischer BS	Ø 8	Ø 10	Ø 12	Ø 14	Ø 18	Ø 24	Ø 28	Ø 35	Ø 35
d_b [mm]	9	11	14	16	20	26	30	40	40
d_f [mm]	7	9	12	14	18	22	26	30	33
d_f [mm]	9	12	14	16	20	26	30	33	40
Sk (h_0,min) [-]	2	2	3	3	5	11	15	18	28
Sk (h_0,max) [-]	2	5	7	10	19	48	75	80	130
max. T_inst [Nm]	5	10	20	40	60	120	150	200	300

FIS A / RG MI

M	M5	M6	M8	M10	M12	M16	M20
ETA-20/0603, Option 7	✓	✓	✓	✓	✓	✓	✓
l_E,min [mm]	8	8	8	10	12	16	20
l_E,max [mm]	14	16	18	23	26	35	45
d₀ [mm]	10	12	14	18	20	24	32
h₀ [mm]	75	75	90	90	125	160	200
fischer BS	Ø 10	Ø 12	Ø 14	Ø 18	Ø 20	Ø 24	Ø 35
d_b [mm]	11	14	16	20	25	26	40
d_f [mm]	6	7	9	12	14	18	22
Sk [-]	2	3	5	7	11	17	48
max. T_inst [Nm]	10	20	40	80	120

Rebar / FRA

Rebar	8	10	12	14	16	20	25	28
FRA	-	-	M12	-	M16	M20	M24	-
ETA-20/0603, Option 1	✓	✓	✓	✓	✓	✓	✓	✓	✓
ETA-20/0603, Option 7	✓	✓	✓	✓	✓	✓	✓	✓	✓
FRA	-	-	✓	-	✓	✓	✓	-
d₀ [mm]	12	14	16	18	20	25	30	35
h_0,min [mm]	60	60	70	80	90	100	112
h_0,max [mm]	160	200	240	280	320	400	500	560
fischer BS	Ø 12	Ø 14	Ø 16	Ø 18	Ø 20	Ø 25	Ø 35	Ø 35
d_b [mm]	14	16	20	20	25	27	40	40
d_f [mm]	-	-	14	-	18	22	26	-
d_f [mm]	-	-	18	-	22	26	32	-
Sk (h_0,min) [-]	3	3	4	5	6	10	13	24
Sk (h_0,max) [-]	7	10	14	18	24	45	65	116
max. T_inst [Nm]	40	60	120	150

FIS E

FIS E	M6	M8	M10	M12
ETA-20/0729, Masonry b, c, d	✓	✓	✓	✓
l_E,min [mm]	6	8	10	12
l_E,max [mm]	60	60	60	60
d₀ [mm]	16	16	20	20
h₀ [mm]	90	90	90	90
fischer BS	Ø 16	Ø 16	Ø 20	Ø 20
d_b [mm]	20	20	25	25
d_f [mm]	7	9	12	14
Sk [-]	12	12	15	15
max. T_inst [Nm]	20

FIS HK

FIS HK	M6	M8	M10	M12
ETA-20/0729, Masonry b, c, d	✓	✓	✓	✓
d₀ [mm]	12	12	16	16
h₀ [mm]	55	55	90	90
d_b [mm]	14	14	20	20
d_f [mm]	7	9	12	14
Sk [-]	12	12	15	15
max. T_inst [Nm]	20

FIS A / RG M, FIS HK

M	M6	M8	M10	M12
FIS HK	12x50	12x85	12x50	12x85	16x85	16x130	16x85	16x130
ETA-20/0729, Masonry b, c, d	✓	✓	✓	✓	✓	✓	✓	✓
d₀ [mm]	12	12	12	12	16	16	16	16
h₀ [mm]	55	90	55	90	90	135	90	135
fischer BS	Ø 12	Ø 12	Ø 12	Ø 12	Ø 16	Ø 16	Ø 16	Ø 16
d_b [mm]	14	14	14	14	20	20	20	20
t_tol [mm]	0	20	0	20	0	20	0	20
d_f [mm]	7	7	9	9	9	9	12	12
Sk [-]	5	10	5	10	12	15	12	15

FIS A / RG M, FIS H 18x130/200 K, FIS H 22x130/200 K

M	M10	M12	M16
FIS HK	18x130/200	18x130/200	22x130/200
ETA-20/0729, Masonry b, c, d	✓	✓	✓
d₀ [mm]	18	18	22
t_tol [mm]	0	0	0
h₀ [mm]	200	200	200
fischer BS	Ø 18	Ø 18	Ø 20
d_b [mm]	20	20	25
d_f [mm]	20	20	24
Sk (h_0,min) [-]	15	15	25
Sk (h_0,max) [-]	35	35	45

FIS A / RG M, PBB, PBZ

M	M8	M10	M12
FIS A / RG M	✓	✓	✓
PBB	✓	✓	✓
PBZ	✓	✓	✓
ETA-20/0729, Masonry b, c, d	✓	✓	✓
h_0,1 [mm]	80	80	80
h_0,2 [mm]	100	100	100
d_f [mm]	9	12	14
Sk (h_0,1) [-]	15	15	15
Sk (h_0,2) [-]	20	20	20
max. T_inst [Nm]	2	2	2

FIS E, PBB, PBZ

FIS E	M6	M8
PBB	✓	✓
PBZ	✓	✓
ETA-20/0729, Masonry b, c, d	✓	✓
l_E,min [mm]	6	8
l_E,max [mm]	60	60
h_0,1 [mm]	100	100
d_f [mm]	7	9
Sk [-]	20	20
max. T_inst [Nm]	2	2

Installation Instructions

Follow these steps for correct installation. Refer to the pictograms for visual guidance.

Cartridge Preparation

Remove the cap by turning it counter-clockwise and pulling it off.
Attach the static mixer to the cartridge and lock it by turning it clockwise. Ensure the spiral mixer is clearly visible. Never use without a static mixer.
Place the cartridge into the dispenser.
Dispense approximately 10 cm (4 inches) of mortar until it appears uniformly grey. Discard any non-grey material as it will not cure.
Ensure the substrate temperature is between 5°C (41°F) and 40°C (104°F). The cartridge temperature should be at least 5°C (41°F).
After use, leave the static mixer attached to the cartridge.

Important: If the working time is exceeded, use a new static mixer. Remove any encrusted material from the cartridge opening if necessary.

Hole Preparation

Drill the hole using a hammer drill. Observe the correct hole diameter and depth as specified in the tables.
Cleaning the Hole: Standing water must be completely removed before cleaning. Blow out the hole with compressed air (≥ 6 bar / 87 psi) four times. Brush the hole four times, starting from the bottom. Blow out again with compressed air four times. For holes with d₀ < 18 mm, a hand pump can be used. Clean brushes regularly.
For deep holes (> 150 mm): Use an extension tube for mortar application.

Mortar Application and Anchor Insertion

Fill approximately 2/3 of the hole with mortar, starting from the bottom. Observe the working time.
Ensure the anchoring element is straight and free from oil or contaminants. Mark the correct embedment depth on the anchor.
Press the anchoring element straight into the hole until it reaches the bottom, turning it slightly.
Excess mortar should emerge from the mouth of the hole.
For overhead or inclined installations, use appropriate injection adapters and wedges to support the anchor during curing. Use adapters for holes deeper than 250 mm or with diameters ≥ 30 mm.

Curing and Load Application

Do not disturb the anchoring element until the prescribed curing time has elapsed.
Do not apply load or installation torque until curing is complete. Refer to Table III for curing times.
Apply the specified installation torque (T_inst) as per Table II.

Installation Pictograms Summary

The following steps are illustrated:

Step 1: Drill hole.
Step 2a/2b/2c/2d: Hole cleaning (blowing, brushing, water removal). Note specific conditions like d₀ ≤ 16 mm, h₀ ≤ 12 d, and pressure requirements (6 bar).
Step 1b/1c/1d: Warning about noise, dust, and the need for cleaning equipment.
Step 3a/3b/3c/3d: Correct (✓) vs. Incorrect (❌) hole cleaning and mortar application.
Step 4: Attaching anchor to dispenser/cartridge.
Step 5: Inserting anchor into the hole.
Step 6a/6b/6c: Correct (✓) vs. Incorrect (❌) mortar application and anchor insertion.
Step 7: Rotating the anchor during insertion.
Step 8: Final insertion and checking embedment depth.
Step 9: Curing time (t_cure) indicated.
Step 10: Applying installation torque (max. T_inst).
Step 11: Final installed anchor.

Contact Information

For further information or support, please contact fischer worldwide:

fischerwerke GmbH & Co. KG
Klaus-Fischer-Straße 1
72178 Waldachtal
Germany
T +49 7443 12-0
info@fischer.de

Visit: www.fischer-international.com

A comprehensive list of fischer contacts in various countries is available on the last page of the original document.

	Fischer FIS V Zero Injection Mortar and Anchoring Systems - Technical Data and Installation Guide Comprehensive technical guide to Fischer FIS V Zero injection mortar and various anchoring systems including FIS A, RG M, FIS E, FIS H K, Rebar, and FRA. Features detailed specifications, installation instructions, temperature/time data, and product information for construction professionals.
	Fischer FIS EP Injection System: Declaration of Performance and Technical Assessment Official Declaration of Performance (DoP) and European Technical Assessment (ETA) for the Fischer FIS EP injection system, a bonded fastener for concrete applications. Details technical specifications, installation guidelines, and performance data for construction professionals.
	fischer FIS EM Plus: Epoxy Mortar for Adhesive Anchoring Systems Comprehensive installation guide and technical specifications for the fischer FIS EM Plus epoxy adhesive anchoring system, detailing applications, performance data, and installation procedures for concrete and rebar connections.
	Fischer Injection Mortar FIS VW Plus, FIS V Plus, FIS VS Plus: Curing and Processing Times Detailed technical data for Fischer injection mortars including FIS VW Plus, FIS V Plus, and FIS VS Plus. Find processing and curing times based on anchoring base temperature.
	Independent Technical Assessment of fischer HybridPower 10x90 Fire Resistance This report presents the independent technical assessment of the fischer HybridPower 10x90 anchor system's performance under fire exposure, evaluated against EAD 330232-01-0601 and EAD 330284-00-0601-v01. It details fire resistance for various load conditions and failure modes in concrete.
	Fischer UltraCut FBS II 8-14 GVZ/CP: Technical Data and Installation Guide Comprehensive technical specifications and installation instructions for the Fischer UltraCut FBS II 8-14 GVZ/CP screw anchor, detailing performance parameters, dimensions, and application guidelines for various concrete and masonry substrates.
	Fischer FIS VW Plus High Speed and FIS V Plus Mortar Curing Times Technical data on curing times for Fischer FIS VW Plus High Speed and FIS V Plus high-performance mortars, detailing processing and curing times based on temperature.
	fischer FFSC Fire Stop Compound: European Technical Assessment ETA-21/0678 Detailed technical assessment of the fischer FFSC Fire Stop Compound, a gypsum-based mortar for fire stopping and sealing in construction. Includes performance data, intended use, and application details for fire compartmentation and protection.