Aviancé HD85961 Lighting Fixture Assembly & Installation Instructions
Model: HD85961
Safety First
⚠️ WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
Please follow all instructions carefully to ensure safe and proper installation.
Assembling the Fixture
Refer to Figure 1 for assembly guidance.
- Shut off the power at the circuit breaker box. Remove the old fixture and all hardware from the Junction Box. Carefully unpack your new fixture and lay out all parts on a clear area. Take care not to lose any small parts necessary for installation.
- Determine the desired hanging height. Slide the electrical wires through the tube(s) (J)/(I)/(H) and canopy (F).
- Raise the tube (J) to the coupling of the fixture body (K). Raise tube (I) and tube (H) to the screw pipe nipple in order, then turn clockwise until tight. Raise the canopy (F) and ground wire onto the pipe nipple of the tube (H), and secure it with the lock washer and hex nut.
- Insert the end of pipe nipple (C) into the single bar (D). Place the lock washer (B) over the end of the nipple protruding through the single bar and secure it with the hex nut (A). Take this single bar assembly to the junction box. Use the junction box screws (E) to tighten screws securely with a screwdriver. The side of the single bar marked "GND" must face outwards. The junction box is not included.
- While holding the fixture body towards the ceiling, connect the electrical wires as shown in Figure 2, ensuring all wire nuts are secured. You may need to wrap the connections with electrical tape. If your outlet has a ground wire (green or bare copper), connect the fixture's ground wire to it. Otherwise, connect the fixture's ground wire directly to the single bar using the green screw provided. After wires are connected, tuck them carefully inside the Junction Box.
- Raise the fixture body onto the Junction Box, aligning the pipe thread on the single bar with the mounting hole in the canopy. Secure it with the finial (G). Raise the glass (L) insert to the lamp holder cover and turn clockwise until tight.
- Install the light bulbs (not included) in accordance with the fixture specifications.
NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!
Your installation is now complete. Return power to the junction box and test the fixture.
Diagram Descriptions
Figure 1: Fixture Assembly Diagram
This diagram illustrates the assembly of the Aviancé HD85961 lighting fixture. It depicts a vertical assembly process starting from a junction box (not included). A ground wire is shown. Components are labeled A through K: A is a hex nut, B is a lock washer, C is the end of a pipe nipple, D is a single bar, E represents junction box screws, F is the canopy, G is a finial, H, I, and J are tubes of varying lengths, and K is the fixture body. The diagram shows how the pipe nipple (C) attaches to the single bar (D) using the lock washer (B) and hex nut (A). The single bar assembly is then attached to the junction box using screws (E). The tubes (J, I, H) and canopy (F) are threaded onto the pipe nipple and secured with a lock washer and hex nut. Finally, the fixture body (K) is attached to the assembly, and the glass (L) is inserted into the lamp holder cover.
Figure 2: Electrical Wire Connections Diagram
This diagram details the electrical connections required for the fixture. It shows three sets of fixture wires: 'FIXTURE WIRES Black or Smooth', 'FIXTURE WIRES White or Ribbed', and 'FIXTURE WIRES Bare Copper (Ground)'. These connect to corresponding 'HOUSE WIRES': 'Black (Hot)', 'White (Neutral)', and 'Green or Bare Copper (Ground)'. The diagram indicates that wire nuts are used to secure these connections. It also specifies that the fixture's ground wire should be connected to the house ground wire (green or bare copper). If no ground wire is present in the house wiring, the fixture's ground wire should be connected directly to the single bar using the provided green screw.
