PRODUCT MANUAL
powerCON TRUE1 TOP | NAC3FX-W-TOP-L
1 APPLICATION INSTRUCTION
IP 65 RATED ?☀️
APPLICATION:
- The powerCON® TRUE1® system is certified as appliance couplers with breaking capacity according to IEC 60320-1, EN IEC 60320-1, UL 60320-1, CSA C22.2 No. 60320-1.
- It serves to supply power to an appliance and from an appliance to other equipment.
- To be installed by qualified person only.
- Appliance couplers acc. to IEC 60320-1 are suitable to be used in cord sets and interconnection cord sets acc. to IEC 60799.
Diagrams illustrating connection types:
- POWER IN: Shows Appliance Inlet connectors (NAC3MPX-TOP, NAC3MPX-WOT-TOP) and a Connector (NAC3FX-W-TOP-L).
- POWER OUT: Shows Appliance Outlet connectors (NAC3FPX-TOP, NAC3FPX-WOT-TOP, NAC3FPX-ST-TOP) and a Plug Connector (NAC3MX-W-TOP-L).
- POWER IN / POWER OUT Combination: Shows Appliance Inlet/Outlet Connector (NAC3PX-TOP) and a Connector (NAC3FX-W-TOP-L) with a Plug Connector (NAC3MX-W-TOP-L).
Products are in compliance with:
| IEC 60320-1 EN IEC 60320-1 | UL 60320-1 CSA C22.2 No. 60320-1 | |
|---|---|---|
| Ratings: | 16A 250V AC | 20A 250V AC |
| Conductor cross section: | 2.5 mm² | 14 - 12 AWG |
| Cable O.D.: | 10.0 - 16.0 mm (0.39 - 0.63") | 10.0 - 16.0 mm (0.39 - 0.63") |
CABLE LIST
| Cable Type | IEC/EN 60320-1 | UL 60320-1, CAN/CSA-C22.2 No. 60320-1 |
|---|---|---|
| H07RN-F | 3 x 2.5 mm² ✔️ | - |
| SOOW | - | 14/3 AWG ✔️ |
| SJOOW | - | 12/3 AWG ✔️ |
2 ASSEMBLY INFORMATION
A
Diagram A: Illustrates placing the bushing (1) and chuck (2) over the cable. Important: Chuck and Bushing cannot be placed over the cable after the assembly of the insert. Use a cable lubricant for easier assembly.
B
Diagram B: Shows cable preparation for IEC/EN 60320-1 and UL/CSA standards. Specifies cable O.D. (10.0 - 16.0 mm (0.39 - 0.63")) and stripping lengths (23 mm for outer jacket, 8 mm for insulation). PE strip length: 26 mm [1.0"].
C
Diagram C: Depicts sliding the cable into the contacts and clamping with a screw using a Torx T8 size tool. Includes a wiring table:
| Typical Wiring | IEC 60320-1 EN IEC 60320-1 | UL 60320-1 CSA C22.2 No. 60320-1 |
|---|---|---|
| L (Line) | brown | black |
| N (Neutral) | blue | white |
| PE (Earth) | green/yellow | green |
Torque Value: 0.7 Nm (6.2 inch pound / 0.52 lb.ft).
D
Diagram D: Details the assembly steps: Position chuck (3) on insert (1). Slide insert (1) with chuck (3) together into housing (2). Important: Align the chuck by positioning the nose into keyway. Slide bushing (4) over chuck (3). Note: Push and turn simultaneously.
2 (Continued)
E
Diagram E: Shows holding the connector with the NEUTRIK tool (5) HTLACA and tightening the bushing with the NEUTRIK tool (6) HTLACB. For exact mounting, use a torque wrench with a 27 mm (1 1/8 inch) hex bit (7) and tighten to 2.5 Nm (22 inch pound / 1.8 lb-ft). Important: The black O-ring must be covered by the bushing to achieve IP protection (8).
3 FOR DISASSEMBLY
- Use the Neutrik tool HTLACB.
- Position the tool on the surfaces and open the clamping sleeve.
Diagram shows the Neutrik HTLACB tool being used to release the connector's clamping sleeve.
4 SAFETY INFORMATION
CAUTION
To ensure protection category, do not expose the connection to bending forces (e.g., do not attach loads to the cable, no free-dangling cable windings, etc.).
SAFETY WARNING
For safety and certification reasons, the connector must be replaced in case of any broken parts or excessive wear and tear.
5 Application and Safety Instructions
A Assembly
- When assembling and processing the product, ensure the use of appropriate personal protective equipment.
- Neutrik components must only be assembled with designated and specified components.
- Replacement parts are suitable only when used in combination with the designated components. The product's characteristics are guaranteed only in the intended combination.
B Application
- The product is exclusively intended for installation in electronic equipment or similar devices.
- The product is not intended for use in medical applications.
- The product is not intended for use in potentially explosive or flammable environments.
- Appliance couplers are not intended for use as climbing aids. Caution: Electrical hazards!
- Ensure that the connectors are either plugged in or protected against moisture with a suitable protective cap in potentially humid environments.
C Operation
- Before plugging in, check the contact area for dry surfaces.
- Product surfaces may cause burns at elevated ambient temperatures. Ensure the use of appropriate protective equipment.
- Neutrik products should only be combined with products from Neutrik Group brands.
D Cleaning
- Clean only with dry and lint-free materials or compressed air.
- The product must not be cleaned while under load. The product may only be cleaned while it is not connected to any voltage and without the use of cleaning agents.
E Damages
- Handle products with care.
- In case of visible damages, check the suitability of the product for use.
6 More Information on the website
For more details, visit: https://www.neutrik.com/en/product/nac3fx-w-top-l
Document No.: BDA 624 V6
Date: 2025-08-18
Manufacturer: Neutrik AG | LI-9494 Schaan | www.neutrik.com
Homepage - Neutrik
