ARRI External Joystick Broadcast EJS-1 and Jog-Wheel EJW-1 User Manual
Document Number: D4510008305 | Version: 1.0 | Date: August 2024
For RCP-2
1 Disclaimer
Before using the product, be sure to read and understand all respective instructions.
The product is available for commercial customers only.
For product specification changes since this document was published, refer to the latest publications of ARRI data sheets or data books, etc., for the most up-to-date specifications.
Not all products and / or types are available in every country. Please check with an ARRI sales representative for availability and additional information.
The information given in this document is subject to change without notice.
While ARRI endeavors to enhance the quality, reliability and safety of their products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risk of damage to property or injury (including death) to persons arising from defects in the products, customers must incorporate adequate safety measures in their work with the system and have to heed the stated canonic use.
ARRI or its subsidiaries expressly exclude any liability, warranty, demand or other obligation for any claim, representation, or cause, or action, or whatsoever, express or implied, whether in contract or tort, including negligence, or incorporated in terms and conditions, whether by statue, law or otherwise. In no event shall ARRI or its subsidiaries be liable for or have a remedy for recovery of any special, direct, indirect, incidental, or consequential damages, including, but not limited to lost profits, lost savings, lost revenues or economic loss of any kind or for any claim by third party, downtime, good will, damage to or replacement of equipment or property, any cost or recovering of any material or goods associated with the assembly or use of our products, or any other damages or injury of the persons and so on or under any other legal theory.
Neither ARRI nor its subsidiaries assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of ARRI products or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property right of ARRI or others.
In the case one or all of the foregoing clauses are not allowed by applicable law, the fullest extent permissible clauses by applicable law are validated.
2 Imprint
© 2024 Arnold & Richter Cine Technik GmbH & Co. Betriebs KG. All rights reserved.
The device contains proprietary information of Arnold & Richter Cine Technik GmbH & Co. Betriebs KG; it is provided under a license agreement containing restrictions on use and disclosure and protected by copyright law. Reverse engineering of the software is prohibited.
No part of this publication may be used for distribution, reproduction, transmission, transcription, storage in a data retrieval system, or translated into any language in any form by any means without the prior written permission of Arnold & Richter Cine Technik GmbH & Co. Betriebs KG.
If you are downloading files from our web pages for your personal use, make sure to check for updated versions.
ARRI cannot take any liability whatsoever for downloaded files, as technical data are subject to change without notice.
Due to continued product development the information in this document may change without notice. The information and intellectual property contained herein is confidential between ARRI and the client and remains the exclusive property of ARRI. If you find any problems in the documentation, please report them to us in writing. ARRI does not warrant that this document is flawless.
ARRI, ARTEMIS 1, ARTEMIS 2, TRINITY 1, TRINITY 2, TRINITY live, SRH3, SRH360 and SRH360-EVO are trademarks or registered trademarks of Arnold & Richter Cine Technik GmbH & Co. Betriebs KG. All other brands or products mentioned are trademarks or registered trademarks of their respective holders and should be treated as such.
Initial Language
The initial language of this operating manual is English. Operating manuals in other languages are translations from English.
In the event of conflict between the respective languages (i.e. if any translation(s) of present document has/have been prepared for convenience or any other purpose), with regards to the meaning or interpretation of a word or an instruction etc., the contents and provisions of the English language version shall prevail.
For Further Assistance
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG
Herbert-Bayer-Str. 10
D-80807 Munich
Germany
E-mail: service@arri.de
Website: www.arri.com/en/technical-service
Original version.
3 About this Document
This operating manual is aimed at everyone involved in using the device. It provides directions on how to operate it safely and as intended. To ensure safe and correct use, all users must read the operating manual before using the device for the first time.
This operating manual is an essential part of the device. It must be easily accessible and in close proximity to the device so that users can use it as a reference anytime.
The separate user manual contains more detailed information about the features and functionalities of the device. Please visit the website www.arri.com to download the user manual.
Keep the operating manual, the user manual and all other operating and assembly instructions belonging to the device in a safe place for future reference and possible subsequent owners.
For useful information in addition to these manuals please have a look at the ARRI learn & help section on the ARRI website.
The ARRI Academy courses provide unrivalled insights into the full possibilities of working with ARRI camera systems, lenses, lighting systems and accessories.
Our advanced service training courses are designed to transfer detailed knowledge about how to service and repair all types of ARRI products and give you permanent access to detailed service instructions, special tools and service parts. To learn more, please visit ARRI academy or contact academy@arri.de.
All directions are given from an operators point of view. For example, device right side refers to the right side of the device when standing behind the device and operating it in a normal fashion.
Connectors are written in all capital letters, for example "USB connector".
Buttons are written in italic typeface capital letters, for example "PLAY button".
Menu paths are written in italic typeface, with menu and home in capital letters, for example "MENU > Display Orientation > Normal".
For more details about the product, please refer to the ARRI website at: EVO-360 product page
The ARRI documentation portal provides important documents on the product for free download.
Please enter the following searchkeys in the search bar to retrieve the documents for the product: EJS-1, EJW-1, K2.0049229, K2.0049230
Document Revision History
| Version | Release | Date | Note |
|---|---|---|---|
| 1.0 | August 2024 | First Release |
4 Safety Instructions
This safety information is in addition to the specific operating instructions in general and must be strictly observed for safety reasons. Read and understand all safety and operating instructions before you operate or install the device. Retain all safety and operating instructions for future reference. Always follow the instructions in this and all documents supplied with the device to avoid injury to yourself or others and damage to the device or other objects.
Assembly and operation should only be carried out by trained staff familiar with the device. Only use the tools, materials and procedures recommended in this document. For the correct use of other equipment, see the manufacturer's instructions.
These instructions use safety instructions, warning symbols and signal words to draw your attention to different levels of risk:
Warning Symbols and Product Labels
- [General warning symbol]
- [Electrical voltage warning symbol]
- [Hot surfaces warning symbol]
- [Sharp element warning symbol]
- [Risk of crushing warning symbol] Please read all instructions carefully before using the product for the first time.
- [Obstacles on the ground warning symbol]
- [DC power symbol]
- Before use, read and follow all relevant instructions.
- Use solely and exclusively as described in the instructions.
- Always use original ARRI / cmotion LBUS cables to external power sources (D-Tap, XLR). ARRI/cmotion LBUS cables to external power sources provide a protection circuit to prevent back currents to power supplies/batteries.
- Do not open the device.
- Do not insert objects into the device.
- Do not built up or assemble the External Joystick Broadcast and External Jog-Wheels the wrong way. It can fall down and cause serious injuries and damage to the device or property.
- Installation and operation must only be carried out by approved persons who know the device. Obey the accident prevention regulations.
- Never put the device on a not stable trolley or hand truck, stand, tripod, bracket, table or any other not stable support device.
- Always place the device on dedicated support devices.
- Always use a suitable safety rope when you use the device above floor level (i.e. on cranes).
- Secure the device and its accessories against falling and tipping over. Obey the general and local safety regulations.
- Risk of injury caused by tripping, falling or slipping over connected cables.
- Always properly secure cables connected to the device and accessories.
- Always install cables that they cannot be tripped over.
- If necessary, use a cable duct or secure the cables with adhesive tape.
- Always disconnect the cables from the device and accessories before moving.
- Mounting the External Joystick Broadcast and External Jog-Wheels poses a crushing hazard for fingers and/or hands.
- Before mounting the External Joystick Broadcast and External Jog-Wheels read the operating instructions provided by the manufacturer.
- Always use the tools specified by the manufacturer for mounting.
- During extended operation and / or operation at high ambient temperatures, the surface of the External Joystick Broadcast and External Jog-Wheels can get hot. Direct sunlight can result in housing temperatures above 60° C (140° F).
- Always use an approved mount to fasten the External Joystick Broadcast and External Jog-Wheels to the system.
- Never hold the External Joystick Broadcast and External Jog-Wheels with bare hands for a long time.
- Do not put covers on the External Joystick Broadcast and External Jog-Wheels while it is powered.
- Do not put the External Joystick Broadcast and External Jog-Wheels near any heat sources during operation.
- At ambient temperatures above 25° C (77° F), prevent the External Joystick Broadcast and External Jog-Wheels from being exposed to direct sunlight.
- May cause physical impairments such as sleep disturbances and stress.
- Always follow the manufacturers instructions.
- Use only External Joystick Broadcast and External Jog-Wheels components approved by ARRI. The use of components not approved by ARRI is at your own risk.
- Obey all relevant safety guidelines.
- Improper handling of the External Joystick Broadcast and External Jog-Wheels bears risk of permanent long term physical damage to the human locomotive system.
- Keep an ergonomic posture when operating and carrying the External Joystick Broadcast and External Jog-Wheels.
- Risk of damage to the External Joystick Broadcast and External Jog-Wheels
- Installation and operation must be done by trained personnel.
- Always read and understand the operating instructions of third-party accessories before you mount recommended the accessories (such as pan bar arm).
- Always use the tools specified by the manufacturer.
5 About this Product
The External Joystick Broadcast EJS-1 can be used as an alternative to the ARRI wheels DRW-1. It controls the pan, tilt, and roll axis of the TRINITY 2 and 360 EVO Remote Head via the Remote Control Panel RCP-2.
The External Jog-Wheels EJW-1 offer three additional, freely programmable jog-wheels. They give the user additional quick access to value adjustment and recall of pre-programmed movements.
5.1 Intended Use
Read and understand the operating manual and the user manual before use.
Use the product and its accessories only for the purpose described in this document. Always follow the safety instructions and system requirements for all equipment involved. ARRI assumes no liability for damages or changes that are caused by improper use. You are not allowed to modify the product and its accessories.
5.2 Identification
The serial number of the External Joystick Broadcast EJS-1 and External Jog-Wheels EJW-1 is located on the underside of the respective housings.
The serial number consists of the last 4 digits of the product number K2.00YYYYYY-1234 (here: 1234).
Diagram showing the underside of the EJS-1 and EJW-1, indicating the location of the serial number.
5.3 Environmental Conditions
The devices should only be used and stored under certain environmental conditions. Check the following conditions before commissioning and operation:
| Condition | Value |
|---|---|
| Permissible Operating Temperature | 20° C to +45° C / -4° F to +133° F |
| Permissible Storage Temperature | -30° C to +70°C / -22° F to +158° F |
| Permissible Humidity | 95% rh, non condensing, from -20° C to +45° C / -4° F to +133° F |
5.4 Technical Data
| EJS-1 | EJW-1 | |
|---|---|---|
| Dimension | See Dimensional Drawings [12] | See Dimensional Drawings [12] |
| Weight (without Mitchell Mount) | 0.77 kg / 1.69 lbs | 0.22 kg / 0.50 lbs |
5.5 Dimensional Drawings
5.5.1 Dimensions EJS-1
EJS-1 dimensions: Height 5.59 inches, Width 7.28 inches, Depth 2.09 inches. Top knob diameter 1.38 inches. All dimensions in inches. Drawing not to scale.
5.5.2 Dimensions EJW-1
EJW-1 dimensions: Height 1.65 inches, Width 4.44 inches, Depth 1.96 inches. All dimensions in inches. Drawing not to scale.
5.6 Scope of Delivery and Warranty
Delivery Sets
- KK.0051102, “EJW-1, Controller Set”: 1x K2.0049230, EJW-1, External Jog-Wheels; 1x K2.0006750, Cable LBUS – LBUS (0.3 m / 1 ft); 1x K2.0042837, CSS Clamp Bridge 52, 19 mm
- KK.0051103, “EJS-1, Controller Set”: 1x K2.0049229, EJS-1, External Joystick Broadcast; 1x K2.0006750, Cable LBUS – LBUS (0.3 m / 1 ft); 1x K2.0042837, CSS Clamp Bridge 52, 19 mm
- KK.0051502, “EJS-1, EJW-1, Controller Set”: 1x K2.0049229, EJS-1, External Joystick Broadcast; 1x K2.0049230, EJW-1, External Jog-Wheels; 2x K2.0006750, Cable LBUS – LBUS (0.3 m / 1 ft); 2x K2.0042837, CSS Clamp Bridge 52, 19 mm
5.7 Certification and Safety Standards
EU Declaration of Conformity
Brand Name: ARRI
Product Description: Accessories for Camera Stabilizer Systems External Joystick Broadcast EJS-1 External Jog-Wheel EJW-1
The designated products conform to the specifications of the following European directives:
- Directive 2014/30/EU EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility.
- Directive 2011/65/EU of the European Parliament and the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment and the Commission Delegated Directive (EU) 2015/863 of March 31, 2015.
Compliance with the requirements of the European Directives has been verified by applying the following standards:
- EN 55032:2015 + AC:2016 + A11:2020 + A1:2020; EN 55035:2017
- EN IEC 63000:2018
Year of affixed CE-marking: 2024
Industry Canada Compliance Statement
Complies with CAN ICES-003(A)/NMB-003(A). This device complies with Industry Canada license - exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
FCC Class A Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- (1) This device may not cause harmful interference, and
- (2) this device must accept any interference received, including interference that may cause undesired operation.
6 Overview
6.1 Overview EJS-1
Diagram of EJS-1 showing: 1. Assignable Push Button, 2. Joystick Pan/Tilt, 3. 3/8in thread / M4 threads, 4. LBUS sockets, 5. Roll axis, 6. Wrist support, 7. CSS Clamp bridge 52 mount.
6.2 Overview EJW-1
Diagram of EJW-1 showing: 1. Marking surface, 2. LBUS sockets, 3. Jogwheels, 4. 3/8in / M4 threads, 5. CSS clamp bridge mount 52 mount.
6.3 Pin Out LBUS Interface
LBUS
Lemo 0B 4pin (24 V max. 3 A)
- Pin 1: Ground
- Pin 2: CAN Low
- Pin 3: + 12 V / + 24 V
- Pin 4: CAN High
*Shown from mating side
7 Mounting and Assembly
To attach the EJS-1 and EJW-1 to 19mm rods, you must attach the CSS Clamp Bridge to the underside of both housings.
7.1 To Mount the Clamp Bridge 52 to EJS-1
When necessary, relocate the two M4 screws located within the CSS Clam Bridge to their outer positions.
Use a 3 mm Hex key to tighten both screws.
7.2 To Mount the Clamp Bridge 52 to EJW-1
When necessary, relocate the two M4 screws located within the CSS Clam Bridge to their outer positions.
Use a 3 mm Hex key to tighten both screws.
7.3 To Wire LBUS / FS-CAN Bus
Diagram showing LBUS and FS-CAN Bus connections between devices.
7.4 Communication Cables
7.4.1 LBUS Cables
Use only appropriate cables, like:
- K2.0006749 Cable LBUS-LBUS (0.2 m / 8 in)
- K2.0006750 Cable LBUS-LBUS (0.3 m / 1 ft)
- K2.0006751 Cable LBUS-LBUS (0.5 m / 1.5 ft)
- K2.0006752 Cable LBUS-LBUS (0.8 m / 2.6 ft)
7.4.2 FS-CAN Bus Cables
Use only appropriate cables, like:
- K2.0019300 SRH FS-CAN Bus Cable (0.2 m / 0.65 ft)
- K2.0033762 SRH FS-CAN Bus Cable (1 m / 3.2 ft)
- K2.0037701 SRH FS-CAN Bus Cable (5 m / 16.4 ft)
- K2.0019302 SRH FS-CAN Bus Cable (10 m / 32.8 ft)
- K2.0019301 SRH FS-CAN Bus Cable (25 m / 82 ft)
8 Cleaning, Repair and Disposal
Improper Cleaning Procedure
Before cleaning, remove all accessories and disconnect all cables.
Only use the cleaning agents specified in this section.
Do not use any strong or aggressive cleaning detergents like Methanol, Acetone, Benzine or acids. These chemicals may dissolve imprinted labels or the paint on the housing and damage highly polished surfaces.
During cleaning of the device, always make sure that protective covers are in place.
Do not moisten connectors when cleaning the device.
Avoid touching any connector pins when cleaning the device.
Avoid wiping dry connector pins with a dry cloth, especially if the surface is not clean.
Avoid wiping connector pins without air blow dusting first. If particles or connector pins are electrostatically charged, it may improve dusting efficiency to use deionized air.
Compressed air should not be used on the housing.
Recommended Cleaning Agents
- Water
- Glass Cleaner
- Isopropyl Alcohol
Cleaning Procedure
| Area | Cleaning Procedure |
|---|---|
| Housing | Clean the housing, mechanical and electronic accessories with a soft, lint free cleaning cloth and some water or glass cleaner. |
| Narrow spaces and gaps | Only when really necessary, e.g. to remove residues of camera tape, isopropyl alcohol should be used. Use a manual air blower, cotton swabs or a soft brush to remove dust particles from narrow spaces, gaps or connectors. |
Repairs carried out by Untrained Personnel
- Do only carry out maintenance work that is describes in this operating manual.
- Do not try to repair the device yourself. Repairs may only be carried out by authorized ARRI service partners.
For repairs and maintenance work on the device, please contact the ARRI Service.
Disposal
When you dispose third party accessories, please observe the instructions of the relevant manufacturer.
This product falls within the scope of Directive 2012/19 / EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of June 4, 2012 on waste electrical and electronic equipment (WEEE II).
Accordingly, this product must not be disposed of with household waste. There are the respective country-specific disposal rules that must be observed.
9 Transportation and Storage
- Risk of damage to the product.
- Always follow the specified environmental conditions.
- Always transport the product and accessories in a suitable case.
- Always follow the instructions for transport and storage described in this section.
The product and its accessories can be damaged if not transported and stored properly. Please take note of the following guidelines.
Transportation Guidelines
- Remove all accessories from the product.
- Always attach protective caps where applicable.
- Always transport the product in a suitable case.
- Do not subject the product to severe shocks.
Storage Guidelines
- Remove the all accessories.
- Disconnect all cables and power sources from the product.
- Always store the product in a suitable case.
- Do not store the product outside of the specified ambient temperature range.
- Do not store the product in places where it may be subject to extreme temperatures, direct sunlight, high humidity, severe vibration, dust or strong magnetic fields.
10 ARRI Service Contacts
Please see the current list of service partners at service contacts.
ARRI Service Contacts
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG
Herbert-Bayer-Str. 10
80807 Munich
Germany
+49 89 3809 2121
service@arri.de
Business hours: Mo. - Fr. 09:00 - 17:00 (CET)
ARRI Inc. / East Coast
617 Route 303
NY 10913 Blauvelt
USA
+1 845 353 1400
service@arri.com
Business hours: Mo. - Fr. 08:30 am - 05:30 pm (EST)
ARRI Inc. / West Coast
3700 Vanowen Street
CA 91505 Burbank
USA
+1 818 841 7070
service@arri.com
Business hours: Mo. - Fr. 09:00 am- 05:00 pm (PT)
ARRI Asia Pte. Ltd.
164 Kallang Way, #03-01
349248 Singapore
Singapore
+65 6230 9488
service@arri.asia
ARRI Australia Pty Ltd
Suite 2, Building B, 12 Julius Ave
NSW 2113 North Ryde
Australia
+61 2 9855 4305
service@arri.com.au
Business hours: Mo. - Fr. 08:00 am - 05:00 pm (AEST)
ARRI Brasil Ltda
Rua Clodomiro Amazonas, 1158 - Lojas 45 e 46,
Vila Nova Conceição
São Paulo, SP 04537-901
Brasil
+55 1150419450
arribrasil@arri.com
Business hours: Mo. - Fr. 09:00 am - 05:30 pm (BRT)
ARRI Canada Limited
76 Six Point Road
Etobicoke, ON M8Z 2X2
Canada
+1 416 255 3335
service@arri.com
Business hours: Mo. - Fr. 08:30 am - 05:00 pm (EDT)
ARRI China (Beijing) Co. Ltd.
Chaowai SOHO Tower C, 6/F, 0628/0656,
Chaowai
Dajie Yi 6
Beijing
China
+86 10 5900 9680
service@arri.cn
Business hours: Mo. - Fr. 09:00 am - 06:00 pm (CST)
ARRI CT Limited / London
2 Highbridge, Oxford Road
UB8 1LX Uxbridge
United Kingdom
+44 1895 457 000
service@arri-ct.com
Business hours: Mo. - Thu. 09:00 am - 5:30 pm (GMT)
Fr. 09:00 am - 5:00 pm (GMT)
ARRI Hong Kong Limited
26/F Gravity, 29 Hing Yip Street
Kwun Tong, Hong Kong
P. R. China
+852 2571 6288
servicehk@arri.asia
Business hours: Mo. - Fr. 09:00 am - 06:00 pm (HKT)
ARRI Korea Limited
42, World Cup buk-ro 1-gil, Mapo-gu
04031 Seoul
Korea
+82 (0)70 4419 6401
service@arri.kr
Business hours: Mo. - Fr. 9:00 - 18:00 (KST)
CINEOM Broadcast DMCC.
HDS Business Center, Unit No. 3503, Floor No.
35 Cluster M
Jumeirah Lake Towers
Dubai
Dubai, UAE
+971 (0) 45570477
arriservice.me@cineom.com
Business hours: Sa. - Th. 9:00 am- 06:00 pm
CINEOM Broadcast India Pvt. Ltd.
C-4, Goldline Business Centre, Link Rd. Malad
West
400 064 Mumbai
India
+91 (0)22 42 10 9000
arrisupportindia@cineom.in
Business hours: Mo. - Sa. 10:00 am - 06:00 pm (IST)
LİNKA GÖRÜNTÜ IŞIK VE SES SİSTEMLERİ TİCARET ANONİM ŞİRKETİ
Distributor & Service
Maslak Mah. AOS 55. Sokak 42 Maslak A Blok SİTESİ
NO: 2 İÇ KAPI NO: 1
Sariyer, Istanbul
Turkey
+90 2123584520
service@linkgroup.com.tr
ARRI | Inspiring Images. Since 1917.
