Alphacool NexXxoS GPX-N 760-M03 Installation Guide
This guide provides instructions for installing the Alphacool NexXxoS GPX-N 760-M03 graphics card cooler.
Important Notes
- Hardware and Cooling System Check: Before installation, ensure your hardware and cooling system (tightness, pump function, fans) are operational. This minimizes troubleshooting time. Alphacool is not liable for manufacturer warranties on electronic components. Installation is at your own risk.
- Screw Tightening: Do not overtighten screws. Overtightening can loosen mounting bolts, preventing uniform cooler contact.
- Connector Installation: It is recommended not to use tools like wrenches for fastening connections. Connectors with 8mm thread length may restrict flow.
- Leak Test: A leak test is recommended before assembling or installing the cooler.
- Contact Verification: Ensure the cooler makes contact with all components to be cooled using thermal grease and thermal pads. The provided image shows the expected imprint on a GPU.
Installation Steps
-
Step 1: Disassembly and Cleaning
Place the hardware on an antistatic mat. Begin by dismantling the original cooler. Remove fan screws and release any covers. Exercise extreme caution with coolers attached by thermal glue, as components can be easily damaged. Carefully collect all original parts. Clean the hardware of thermal paste or pad residue using a solvent (e.g., alcohol).
-
Step 2: Apply Thermal Paste
Using a plastic strip or thermal paste spreader, apply a thin, even layer of thermal paste to the GPU. The layer should be less than a millimeter thick to avoid contaminating surrounding components.
-
Step 3: Apply Thermal Pads
Remove the protective film from the thermal pads. Place the 15mm x 15mm x 1.5mm pads on the memory chips. The 30mm x 30mm x 1.5mm pads are for the voltage converters and may need to be trimmed to size. Remember to remove the protective film from both sides of all pads.
-
Step 4: Mount the Cooler
Mount the assembled cooler onto the graphics card as shown in the image. If there is a protective film on the cooler's base, remove it now. Clean the contact surfaces on the cooler's base with alcohol or a similar agent to ensure they are free of contaminants.
-
Step 5: Apply Rear Thermal Pads
Cut the yellow thermal pads as shown in the image for the backplate. Place these on the rear side of the voltage converters and the GPU. Ensure protective film is removed from both sides.
-
Step 6: Install Backplate
Place the backplate onto the graphics card as depicted. Apply gentle pressure for optimal contact between the backplate, cooler, and graphics card.
-
Step 7: Final Assembly and Tightening
Screw the cooler together. Finger-tighten the screws with one turn each, following a cross pattern. Refer to the instructions for specific guidance. After approximately 12 hours of graphics card usage, re-tighten all screws.
Safety Information
- Not suitable for children under 6 years (contains small, swallowable parts).
- Never operate cooling components without ensuring coolant flow. Coolers without coolant can overheat and cause burns or damage computer hardware. Always verify the pump is functioning when the hardware is powered on.
- Do not use tools (wrenches, pliers, etc.) to tighten connectors. Plastic or metal threaded connections can be easily overloaded, leading to cracks or damage. Coolant leaks resulting from improper tightening are not covered by the warranty. Use connectors with sealing rings, which only require hand-tightening. Tools may only be used if explicitly indicated in the manual.
Intended Use
Alphacool International GmbH cooling components are approved for cooling computer parts. Warranty is void for any other use.
Warranty Information
- Information in brochures, catalogs, etc., is for informational purposes only. Alphacool does not guarantee the accuracy of this data. Order and order confirmation details are decisive for the scope of delivery.
- If a defect exists, customers are entitled to demand rectification, withdraw from the contract, or reduce the purchase price according to legal provisions. The warranty period is two years from receipt of goods for consumers and one year for entrepreneurs.
- Warranty claims require the original invoice, sales receipt, or an ALPHACOOL confirmation.
- ALPHACOOL INTERNATIONAL GMBH reserves the right to repair or replace defective products or components. Replaced items become the property of ALPHACOOL INTERNATIONAL GMBH.
- Warranty claims are handled by ALPHACOOL INTERNATIONAL GMBH or authorized dealers. Repairs by unauthorized personnel void the warranty unless pre-approved by ALPHACOOL INTERNATIONAL GMBH.
- ALPHACOOL INTERNATIONAL GMBH does not cover costs associated with product retrofitting.
- The warranty excludes: regular checks, maintenance, repairs, replacement of wear parts, incorrect operation or installation defects, damages from natural disasters (storm, water, fire, overvoltage, war), incorrect power connection, inadequate ventilation, or other external factors. Transportation or improper packaging damages are also excluded.
- Consumer rights in the respective country and claims against the seller are not affected by this warranty. ALPHACOOL INTERNATIONAL GMBH, its branches, and distributors are not liable for direct or indirect damages or losses unless mandated by law.
- Alphacool International GmbH does not assume the manufacturer's warranty for electronic components. Cooler assembly is at your own risk.
Contact Information
Address:
Alphacool International GmbH
Marienberger Str. 1
D-38122 Braunschweig
Support Phone: +49 (0)5 31/288 74-100
Fax: +49 (0)5 31/288 74-22
Email (German/English): info@alphacool.com
Internet: www.alphacool.com
Forum: Accessible via the homepage.
RoHS Compliance
All parts of the cooling system are RoHS compliant (2002/95/EC).
Disposal Information
Dispose of this product through an authorized waste management company. Do not dispose of with household or unsorted municipal waste.
