Philips Dynalite PAxBPE AntumbraButton User Interface

Safety and Installation Requirements

Devices must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations.

This applies to all languages and regions, ensuring safe and compliant installation.

Installation Steps

Step 1: Prepare for Mounting

This step involves preparing the wall for the device. The components shown include:

• A back box for wall installation.
• Mounting brackets (x2).
• Screws (x2) for securing components.
• A wall plate.

The diagram illustrates these parts laid out for assembly.

Step 2: Install the Wall Box

The wall box is installed into the wall opening. Key dimensions for the wall box are:

• Height: 88 mm (3.46 in)
• Width: 63 mm (2.48 in)
• Depth: 52 mm (2.05 in)

Additionally, two types of wall plates are shown with their dimensions:

• Plate 1: 88 mm (3.46 in) height x 60 mm (2.36 in) width.
• Plate 2: 88 mm (3.46 in) height x 36 mm (1.41 in) width.

Step 3: Route Wiring

Wiring is routed into the installed wall box. Ensure adequate clearance for wiring:

• Minimum clearance from walls: ≥ 300 mm (11.81 in) horizontally and vertically.
• Minimum clearance from other services: ≥ 0 mm (0 in).

Step 4: Secure the Wall Box

The diagram shows the wall box being secured within the wall structure.

Step 5: Attach the Wall Plate

The wall plate is attached to the wall box, preparing for the final device installation.

Step 6: Connect Wiring

Wiring connections are made to the terminals inside the wall box. Specifications for wiring are:

• Wire Gauge: 0.3-2.5mm² (22-12 AWG)
• Torque: 0.4 Nm (3.5 Lb-in)

The terminals are labeled for specific connections:

• +V (Positive Voltage)
• D- (Data Negative)
• D+ (Data Positive)
• GND (Ground)
• SHLD (Shield)

For SELV/Class 2 (UL) connections, the ratings are 12 V at 35 mA or 24 V at 20 mA. The maximum current for communication wires is ≤ 2 A.

Step 7: Connect RS-485 DyNet

The RS-485 DyNet communication bus is connected. Specifications for these terminals are:

• Torque: 1.0 Nm (8.8 Lb-in)
• Terminals: +V, D-, D+, GND, SHLD

Step 8: Attach the AntumbraButton Front Plate

The front plate of the AntumbraButton, featuring ON/OFF indicators, is attached to complete the device installation.

Step 9: Install RS-485 DyNet Module

The separate RS-485 DyNet module is installed as part of the system.

Technical Specifications and Environmental Conditions

• IEC Pollution Degree: II
• Operating Temperature: -5° C (23° F) to 50° C (122° F)
• Operating Humidity: ≤90% (non-condensing)

Compliance and Certifications

This equipment complies with various standards and regulations:

Federal Communications Commission (FCC) Compliance Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any modifications not approved by the manufacturer of this device could void the user's authority to operate this device.

Canadian Compliance: This Class B digital apparatus complies with Canadian ICES-003: CAN ICES-3(B)/NMB-3(B). Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada: CAN ICES-3(B)/NMB-3(B).

General Installation Compliance: Installation of a home and building automation and control system shall comply with IEC 60364 (all parts). The temperature limits and current-carrying capacities for the communication wires specified in IEC 60364-5-52 shall not be exceeded.

Important Notes

⚠️ Do not connect inputs to mains.

⚠️ Disconnect power before connecting or separating modules.

Refer to the Service Guide for full cleaning recommendations.