MULTIBRACKETS M Projector Mount HD Installation Guide

⚠️ Important Safety Information

Your projector equipment represents a considerable value. Ensure all mounting hardware is suitable for your wall, ceiling, or floor material. If you are unsure about any aspect of the mounting process, consult a professional.

ℹ️ Warranty Information

MULTIBRACKETS offers a limited product warranty:

• FIVE (5) years: Metal video monitor mounts; all racks and non-electrical rack accessories.
• TWO (2) years: Gaslifts and sit-stand workstations.
• ONE (1) year: Motorized/automated products; plastic speaker mounts; speaker stands; furniture; wood accessories.

For warranty claims, create an RMA case on www.multibrackets.com/support. The warranty covers defective parts but not labor costs for removal/replacement. It is void if the product is modified, improperly installed, overloaded, misused, or used outdoors. Wall/ceiling mounts are void if moved from initial installation. MULTIBRACKETS disclaims other warranties and liability for incidental/consequential damages.

? Parts List

⚙️ Installation Steps

Step 1: Assemble Pole Components

Connect the pole (A) to the projector plate (C) and ceiling plate (B) using the specified screws (e.g., M-A, M-B, M-C, M-D, M-E, M-F, M-G, M-H). Refer to the diagrams for correct orientation and screw placement.

Step 2: Mount Ceiling Plate

Attach the ceiling plate (B) securely to the ceiling. The process varies based on ceiling type:

Method 4a (Flat Ceiling):

Use screws (W-A, W-C) to fix the ceiling plate. Diagrams indicate using a drill guide for precise hole placement. Ensure a minimum fixing depth of 30mm.

Method 4b (Angled/Other Ceilings):

Alternative methods are shown for different ceiling materials, utilizing screws (W-A, W-B, W-C) and potentially wall anchors. Ensure a robust and secure attachment.

Step 3: Adjust Pole Height

Insert the assembled pole into the ceiling plate. Adjust the desired height by loosening the locking screws (M-J), extending or retracting the pole, and then re-tightening the screws to secure the position.

Diagram shows inserting the pole, adjusting height via screws.

Step 4: Attach Projector to Plate

Mount the projector onto the projector plate (C) using the appropriate screws (e.g., M-F, M-G) that match your projector's VESA mounting holes. Ensure the projector is firmly secured to the plate.

Diagram shows attaching the projector to the plate and tightening screws.

Step 5: Cable Management

Route projector cables through the pole. The diagrams illustrate feeding cables either inside or outside the pole, securing them with provided cable ties. EANs 7350073735211, 7350073735228, 7350073735235 are associated with cable management options.

Step 6: Final Adjustments

After mounting and height adjustment, fine-tune the projector's position:

• Tilt: Adjust the tilt angle of the projector plate up or down by approximately ±20 degrees.
• Swivel: Rotate the entire mount assembly around the pole up to 360 degrees (?).
• Locking: Ensure all adjustment screws are tightened securely to maintain the desired position.

Diagrams illustrate these tilt and swivel adjustments.

Step 7: Model-Specific Lengths

The M Projector Mount HD series is available in three length variations:

• M Projector Mount HD 305-345mm
• M Projector Mount HD 620-800mm
• M Projector Mount HD 970-1500mm

These lengths refer to the minimum and maximum extension capabilities of the pole.

? Dimensions and Angles

The mount supports projectors with mounting patterns up to Ø400mm. The pole diameter is approximately Ø50mm, and the ceiling plate diameter is approximately Ø42mm. The mount allows for tilt adjustments of ±20 degrees and a full 360-degree swivel.

Diagram shows the pole assembly with key dimensions: Ø42mm (ceiling plate), Ø50mm (pole), min Ø180mm - max Ø400mm (projector plate mounting pattern). It also indicates a 90° angle for ceiling attachment, ±180° (likely intended as 360° swivel range), and ±20° tilt.