HOMCOM 83B-048V70 2-Seater Pull-Out Sofa Bed
Model: IN240701678V02_GL
Important Information
Please read carefully and retain for future reference.
This product is intended for domestic use only.
⏰ Estimated assembly time: 30 minutes. ?♂️ Assembly steps: 7. ?️ Maximum load capacity: 250 kg.
Precautions Before Assembly:
- Prepare a clean and dry assembly area.
- Verify that the product is not damaged.
- Check that none of the pieces are missing.
Instructions for Use:
- Place the sofa bed stably on a flat floor.
- Keep away from open flames and heat sources.
- Avoid overloading the sofa bed.
Maintenance:
- Clean with a soft fabric.
- Check the seating and structure regularly.
Storage Conditions:
- The fabric should be stored completely dry, in a clean and dry place to avoid the risks of mold.
Assembly Hazards:
Beware of crushing and cutting hazards during assembly.
The manufacturer declines all responsibility in case of damages due to bad installation or weather conditions.
If the sofa bed is fitted with powered seat height adjustments (not applicable to this model), only trained personnel may replace or repair those components.
Parts List
- Part A: Sofa frame basex 1
- Part B: Side frames (Left & Right)x 2
- Part C: Sofa seat/backrest cushionx 1
- Part D: Front support barx 1
- Part E: Armrest cushionsx 2
- Part F: Support bracketsx 4
- Part G: Feetx 4
- Part H: Side bracketsx 2
- Part I: Allen keyx 1
- Part J: M6*20MM screwsx 24 + 1 spare
- Part K: M6*60MM screwsx 2
- Part L: M8*100MM screwsx 8 + 1 spare
- Part M: Wrenchx 1
- Part N: M6*45MM screwsx 10 + 1 spare
- Part O: M6*45MM screwsx 4
- Part P: Mounting platesx 2
- Part Q: Pre-installed connectorsx 2
Assembly Instructions
Step 01
Attach side frame B(R) to the sofa frame base A. Use screws L (4 pcs) and N (4 pcs). Tighten with wrench M.
Diagram shows attaching the right side frame to the base, secured by screws.
Step 02
Attach side frame B(L) to the sofa frame base A. Use screws L (4 pcs) and N (4 pcs). Tighten with wrench M.
Diagram shows attaching the left side frame to the base, secured by screws.
Step 03
Attach the front support bar D between the side frames. Use side brackets H and screws J. Arrows indicate insertion and tightening.
Diagram shows connecting the front bar using brackets and screws.
Step 04
Attach support brackets K&N to the inside of the side frames. Use screws J. Arrows indicate insertion and tightening.
Diagram shows attaching internal support brackets with screws.
Step 05
Screw the feet G into the designated points on the bottom of the sofa frame.
Diagram shows screwing the four feet into the base.
Step 06
Attach support brackets F to the underside of the sofa seat/backrest cushion C. Use screws J. Tighten with Allen key I.
Diagram shows attaching brackets to the underside of the main cushion.
Step 07
Attach mounting plates P to the underside of the sofa seat/backrest cushion C using screws O. Note the pre-installed connectors Q.
Diagram shows attaching mounting plates to the cushion, ready for connection. The step is marked as 'Done'.
Operation Guide
To Extend the Sofa Bed: Pull the seat section upwards and forwards.
To Fold the Sofa Bed: Push the seat section downwards and backwards.
Note: "This part cannot be taken out."
Diagrams illustrate the pulling motion to extend and the pushing motion to fold the sofa bed.
Contact & Support Information
For any questions or assistance, please contact the relevant customer care center:
United States (US)
Company: Aosom LLC
Phone: 001-877-644-9366
Email: customerservice@aosom.com
Address: 27150 SW Kinsman Rd, Wilsonville, OR 97070 USA
Origin: MADE IN CHINA
Canada (CA)
Company: Aosom Canada Inc.
Phone: 416-792-6088
Email: customerservice@aosom.ca
Address: 7270 Woodbine Avenue, Unit 307, Markham, Ontario Canada L3R 4B9
Origin: MADE IN CHINA
France (FR)
Company: MH FRANCE
Phone: 0033-1-84166106
Email: aosom@mhfrance.fr
Address: 2 Rue Maurice Hartmann, 92130 Issy Les Moulineaux, France
Origin: FABRIQUÉ EN CHINE
Germany (DE)
Company: MH Handel GmbH
Phone: +49 40 87408465
Email: service@aosom.de
Address: Wendenstraße 309, D-20537 Hamburg, Germany
Origin: IN CHINA HERGESTELLT
Italy (IT)
Company: AOSOM Italy srl
Phone: 0039-0249471447
Email: clienti@aosom.it
Address: Centro Direzionale Milanofiori, Strada 1 Palazzo F1, 20057 Assago (MI)
Origin: FATTO IN CINA
Spain (ES)
Company: SPANISH AOSOM, S.L.
Phone: 0034-931294512
Email: atencioncliente@aosom.es
Address: C/ROC GROS,N°15.08550, ELS HOSTALETS DE BALENYÀ, SPAIN.
Origin: HECHO EN CHINA
United Kingdom (UK)
Company: MH STAR UK LTD
Phone: 0044-800-240-4004
Email: enquiries@mhstar.co.uk
Address: Unit 27, Perivale Park, Horsenden lane South, Perivale, UB6 7RH
Origin: MADE IN CHINA
Portugal (PT)
Company: SPANISH AOSOM, S.L
Phone: 0034-931294512
Email: info@aosom.pt
Address: C.ROC GROS N.15, 08550. ELS HOSTALETS DE BALENYÀ
Origin: FEITO NA CHINA
Recycling information: ♻️ See addresses on quefairedemesdechets.fr
