HOMCOM L-Shape Sofa Assembly Instructions

Important Information & Care

Important: Retain for future reference. Read carefully.

This product is intended for domestic use only.

Instructions for Use:

• Place the sofa stably on a flat floor.
• Stay away from open flames and heat sources.
• Avoid overloading the sofa.

Precautions Before Assembly:

• Prepare a clean and dry mounting area.
• Verify that the product is not damaged.
• Check that none of the pieces are missing.

Maintenance:

• Clean with a soft fabric.
• Check the seating regularly.

Storage Conditions:

• The fabric should be stored completely dry, in a clean and dry place to avoid the risks of mold.

Safety Warning:

Beware of crushing and cutting hazards during assembly. The manufacturer declines all responsibility in case of damages due to bad installation or environmental factors.

If the sofa is fitted with powered seat height adjustments (not applicable to this model based on visuals), only trained personnel may replace or repair those components.

Parts List

• A: Main Sofa Base Frame (x1) - The primary structure of the sofa.
• B: Seat Base / Ottoman Base (x1) - A smaller rectangular base, likely for the chaise section.
• C: Left Armrest/Side Panel (x1) - A curved panel forming one side of the sofa.
• D: Right Armrest/Side Panel (x1) - A curved panel forming the other side of the sofa, mirroring panel C.
• E: Large Seat Cushion (x1) - The main cushion for the chaise section.
• F: Standard Seat Cushions (x2) - Cushions for the main sofa seating areas.
• G: Backrest Frame (x1) - A long, narrow frame that supports the back cushions.
• I: Back Cushions (x3) - Cushions that rest against the backrest frame.
• J: Sofa Legs (x8) - Tapered cylindrical feet for supporting the sofa.
• K: Support Bar (x1) - A metal rod used for structural support.
• L: Metal Bracket/Connector (x1) - A piece used for joining components.
• M: Chaise Armrest/Side Piece (x1) - An L-shaped piece that forms the armrest for the chaise.
• N: Standard Armrest/Side Piece (x2) - Curved pieces that form the armrests for the main sofa sections.

Hardware List

• 1: M8x18mm Bolt (x4, +1 spare)
• 2: M8x60mm Bolt (x12, +1 spare)
• 3: M8 Washer (x12, +1 spare)
• 4: M4x30mm Screw (x32, +1 spare)
• 5: Hex Key (Allen Wrench) (x1)

Assembly Steps

Step 01: Attach Side Panels to Base Frame

Connect the Left Armrest/Side Panel (C) and the Right Armrest/Side Panel (D) to the Main Sofa Base Frame (A). Use eight M8x60mm Bolts (2) and eight M8 Washers (3) for this connection. Tighten using the Hex Key (5).

Visual: Shows panels C and D being attached to the ends of frame A, with bolts and washers inserted into pre-drilled holes.

Step 02: Install Support Bar

Attach the Support Bar (K) to the Main Sofa Base Frame (A). Use two M8x18mm Bolts (1) and the Hex Key (5) to secure it in place.

Visual: Shows the metal rod K being attached to the underside of frame A.

Step 03: Attach Sofa Legs to Seat Base

Turn the Seat Base/Ottoman Base (B) upside down. Attach all eight Sofa Legs (J) to the designated mounting points on the underside of base B. Ensure they are screwed in securely.

Visual: Shows the rectangular base B with eight legs J being screwed into its corners and mid-points.

Step 04: Connect Seat Base to Main Frame

Attach the assembled Seat Base/Ottoman Base (B with legs J) to the Main Sofa Base Frame (A). Use two M8x18mm Bolts (1) and two M4x30mm Screws (4) to connect the two main sections. Tighten with the Hex Key (5).

Visual: Shows the base B being joined to the main frame A, with bolts and screws being used at the connection points.

Step 05: Attach Backrest Frame

Position the Backrest Frame (G) onto the main sofa structure. Secure it using four M8x60mm Bolts (2) and four M8 Washers (3). Tighten with the Hex Key (5).

Visual: Shows the backrest frame G being attached to the rear of the assembled sofa base.

Step 06: Place Seat Cushions

Place the Large Seat Cushion (E) onto the chaise section of the sofa. Place the two Standard Seat Cushions (F) onto the main seating area of the sofa.

Visual: Shows cushions E and F being placed onto the sofa structure.

Step 07: Attach Armrest/Side Pieces

Attach the Chaise Armrest/Side Piece (M) to the chaise section. Attach the two Standard Armrest/Side Pieces (N) to the sides of the main sofa seating area. These pieces likely slot or attach via pre-fitted hardware.

Visual: Shows pieces M and N being positioned and attached to the respective sides of the sofa.

Step 08: Final Cushion Arrangement

Ensure all seat cushions (E, F, F) are correctly positioned and aligned on the sofa frame.

Visual: A final view of the sofa with all seat cushions in place.

Step 09: Place Back Cushions

Place the three Back Cushions (I) against the Backrest Frame (G) on the sofa.

Visual: Shows the three back cushions I being placed against the back of the sofa.