PERLEGEAR PGLT5 Tilting TV Wall Mount

Compatibility Check & Specifications

Before proceeding, ensure your TV is compatible with this mount.

VESA Compatibility:

• Max VESA: 600 x 400mm (23.6 x 15.7 inches)
• Min VESA: 200 x 100mm (7.9 x 3.9 inches)

Maximum Load Capacity: 132 lbs (60kg)

Important Safety Warnings & Precautions

DANGER: Please read all instructions carefully before attempting installation. If you do not understand the instructions or have any questions or concerns, please contact PERLEGEAR.

CAUTION: Avoid the risk of personal injury and property damage!

WARNING: All fasteners must be firmly tightened!

• Before starting assembly, verify that all parts and hardware are included and undamaged. Do not use damaged or defective items. If you require replacements, please contact PERLEGEAR.
• This product is designed for installation on solid concrete and wood walls. Do not install on drywall alone.
• The wall must be capable of supporting four times the weight of the TV and mount combined.
• This product contains small parts that may pose a choking hazard.
• Do not use this product for any purpose not explicitly specified in this manual. Do not exceed the maximum weight capacity. PERLEGEAR is not liable for damage or injury caused by incorrect assembly, improper mounting, or inappropriate use.
• Use this mounting system only for its intended purpose as described in these instructions. Do not use attachments not recommended by the manufacturer.
• Do not use outdoors.
• Route cords and cables properly to avoid mechanical damage.

SAVE THESE INSTRUCTIONS

Tools Required

• Pencil ✏️
• Phillips Screwdriver ?
• Electric Drill ?
• Tape Measure ?
• 7/16" (11mm) Socket Wrench ?
• Hammer ?
• 3/8" (10mm) Concrete Drill Bit
• 5/32" (4mm) Wood Drill Bit

Parts Included

Installation Steps

Step 1: Attach TV Brackets to TV

Select the appropriate TV bolts (F, D, or E) and spacers (C1/B1, C2/B2/B3) that fit your TV's VESA mounting holes. The correct bolt diameter should thread smoothly into the VESA mounting holes. Only one size typically fits your TV.

Instructions:

1. Identify the correct bolt and spacer combination for your TV.
2. Thread the selected bolts through the TV brackets (01, 02) and into the VESA holes on the back of your TV.
3. Ensure the bolts are snug but do not overtighten.
4. Warning:
   • The depth of the bottom holes may differ from the top holes.
   • If the bolt is too short, it may not adequately support the TV.
   • Do not turn the bolt past the bottom of the hole.
   • If the bolt is too long, it could damage the TV.
   • At least 4-5 turns into the threading are required for secure mounting.

Diagram Description: Shows selecting bolts and spacers, then attaching them to the TV brackets which are then aligned with the TV's VESA holes. A checkmark indicates correct attachment, a cross indicates incorrect.

Step 2: Mount the Wall Plate

Choose the appropriate mounting option based on your wall type.

Option A: For Solid Concrete Walls

Warning: Avoid the risk of personal injury or property damage! Tighten the lag screws [A1] only until they are pulled firmly against the wall plate (do not overtighten). Do not use a drill; only use a socket wrench. Use wall anchors [A2] for this mounting option. Mount the wall plate directly on the concrete surface.

Diagram Description: Illustrates drilling holes into a concrete wall using a 3/8" (10mm) drill bit, inserting wall anchors (A2), and then securing the wall plate using lag screws (A1) with a socket wrench. A minimum concrete depth of 8" (203mm) is indicated.

Option B: For Wood Walls

Warning: Avoid the risk of personal injury or property damage! Tighten the lag screws [A1] only until they are pulled firmly against the wall plate (do not overtighten). Do not use a drill; only use a socket wrench. Do not use wall anchors [A2] for this mounting option.

Diagram Description: Illustrates drilling pilot holes into wood studs using a 5/32" (4mm) drill bit. The wall plate is then secured directly to the wood studs using lag screws (A1) with a socket wrench. A minimum wood depth of 2.36" (60mm) is indicated.

Step 3: Attach TV to Wall Plate

Carefully lift your TV and hook the TV brackets onto the wall plate. Ensure the brackets are securely engaged.

Locking Mechanism:

Pull down on the safety straps/cables attached to the TV brackets, then release them to lock the TV in place. You should hear or feel a click.

Diagram Description: Shows lifting the TV with attached brackets and hooking them onto the wall plate. A close-up shows pulling down a release strap and then releasing it to lock the bracket onto the wall plate.

Step 4: Adjustments and Final Checks

Tilt Adjustment: If the tilt adjustment does not hold, fully tighten the bolts on the tilt mechanism.

Diagram Description: Shows a hand tightening a bolt on the tilt mechanism with a tool, indicating how to adjust or secure the tilt angle.

Troubleshooting

Tilt won't hold? Fully tighten the bolts on the tilt mechanism.

Removing the TV

Unlock: Pull down on the safety straps/cables to unlock the TV brackets from the wall plate.

Note: Disconnect all cables before removing the TV.

Diagram Description: Shows pulling down the release straps to unlock the TV from the wall mount.