PERLEGEAR

1. Check VESA Pattern Compatibility

Compatible VESA Patterns:

• 200 x 100mm
• 200 x 200mm
• 200 x 300mm
• 200 x 400mm
• 300 x 200mm
• 300 x 300mm
• 300 x 400mm
• 400 x 200mm
• 400 x 300mm
• 400 x 400mm
• 500 x 400mm
• 600 x 400mm

Maximum/Minimum: 800 x 400mm (31.5" x 15.7"), 200 x 100mm (7.9" x 3.9")

If this mount is not compatible, please contact product support.

Diagram showing VESA hole measurements: Max height 400mm (15.7"), Max width 800mm (31.5").

2. Check Max Load

Maximum Load Capacity: 132 lbs (60kg)

WARNING: DO NOT exceed the Max Load. Exceeding the Max Load can cause the mount to fail, leading to personal injury and/or property damage.

If your TV weighs more, this mount is NOT compatible.

3. Verify Wall Type

This mount is designed for installation on wood studs (with drywall) or solid concrete.

WARNING: DO NOT install on drywall alone.

Diagrams illustrating wood studs with drywall and solid concrete, both marked as 'Perfect' for mounting.

Wood stud dimensions: 24" (610mm) and 16" (406mm) on center.

4. Tools Needed (not included)

• Electric Drill
• Pencil
• Stud Finder
• Hammer
• Phillips Screwdriver

For Wood Stud Walls:

• 5/32" (4mm) Awl
• Wood Drill Bit
• 5/16" (8mm) Drywall Drill Bit

For Solid Concrete:

• 5/16" (8mm) Concrete Drill Bit

5. Important Safety Information

CAUTION: Avoid the risk of personal injury or property damage!

• This product is designed for installation on wood studs and solid concrete. DO NOT install on drywall alone.
• The wall must be capable of supporting four times the weight of the TV and mount combined.
• This product contains small parts that may pose a choking hazard.
• Do not use this product for any purpose that is NOT explicitly specified in this manual.
• Do not exceed the maximum weight capacity. Perlegear is not liable for damage or injury caused by incorrect assembly, improper mounting, or inappropriate use.
• Before starting assembly, verify that all parts are included and undamaged. Do not use damaged or defective parts. For replacement parts, contact technical support or email customer service.
• This product is only compatible with most Samsung TVs.

WARNING: All fasteners must be firmly tightened!

Step 1

Paper Tape Measure 05 x 1

Step 2

L TV Bracket 03 x 1

R TV Bracket 04 x 1

Plastic Pad B x 2

Spacer C x 2

TV Bolt M8 x 10mm D1 x 2

TV Bolt M8 x 18mm D2 x 2

TV Bolt M8 x 55mm D3 x 2

Diagrams of parts for Step 2.

Step 3

EVA Pad E x 4

EVA Pad F x 2

Kickstand G x 1

TV Bolt M8 x 18mm D2 x 1

Diagrams of parts for Step 3.

Step 4

Wall Plate 01 x 1

Wall Plate 02 x 1

Paper Tape Measure 05 x 1

Level 06 x 1

Sticker H x 1

Lag Screw ST 5.5 x 55mm A1 x 8

Wall Anchor A2 x 8

CAUTION! This anchor is for solid concrete and drywall ONLY. DO NOT use them in wood studs.

Diagrams of parts for Step 4.

STEP 1 Measure the TV

To determine the center point of the TV, measure the following:

• a = distance between the VESA holes
• b = height of the TV
• c = half of the distance between the VESA holes (1/2a)
• d = center point of the TV

Diagram illustrating measurements a, b, c, and d on a TV.

STEP 2 Attach the TV Brackets to Your TV

WARNING:

• DO NOT turn the bolt past the bottom of the hole.
• If the bolt is too short, it may not adequately support the TV.
• If the bolt is too long, it could damage the TV.
• At least 4-5 turns into the threading is required.

Diagrams showing correct and incorrect bolt lengths ('Too Short', 'Too Long').

For TV with VESA Holes, go to Option A on this page.

For TV with Recessed Mounting Holes, go to Option B on the next page.

Option A

Diagram showing attachment of TV Brackets (03 L, 04 R) to the TV using TV Bolts (D1, D2, D3) and Washer (C). Ensure to use the upper VESA holes.

DO NOT overtighten.

Diagrams showing correct and incorrect bracket placement.

Option B

Diagram showing attachment of Plastic Pad (B) and then TV Brackets (03 L, 04 R) to the TV using TV Bolts (D1, D2, D3) and Washer (C) for TVs with recessed mounting holes.

DO NOT overtighten.

Diagrams showing correct and incorrect bracket placement.

STEP 3 Attach the EVA Pads and Kickstand

Diagram showing attachment of EVA Pads (E x 4) to the TV brackets.

Diagram showing attachment of Kickstand (G) to the TV bracket using TV Bolt (D2).

One Connect Box Mounting Instruction

These parts are included with the TV, not this product.

Diagram showing attachment of the One Connect Box using screws.

Diagram showing attachment of EVA Pads (F x 2) to the wall plates.

STEP 4 Mount the Wall Plates on the Wall

For mounting on wood stud walls, go to Option A on pages 10 to 12.

For mounting on solid concrete, go to Option B on pages 12 to 14.

Option A: For Wood Stud Installation

Diagram showing wood stud dimensions: 24" (610mm) and 16" (406mm) on center. Max stud width 5/8" (16mm). Nominal stud depths: 2" (51mm) actual 1 1/2" (38mm), and 4" (102mm) actual 3 1/2" (89mm).

Tools Needed (Not Included): Electric Drill, Pencil, Stud Finder, 5/32" (4mm) Awl, Wood Drill Bit, 5/16" (8mm) Drywall Drill Bit, Hammer, Phillips Screwdriver.

WARNING: Avoid the risk of personal injury or property damage! Tighten the lag screws [A1] only until they are pulled firmly against the wall plate (DO NOT overtighten). Do not use a drill; only use a Phillips screwdriver. Do not use wall anchors [A2] for this mounting option.

Diagram showing a wall anchor [A2] and a warning not to use it with wood studs.

1. Find Studs and Mark Holes: Diagram showing how to locate studs and mark hole positions using a level and tape measure.
2. Mark Hole Positions: Diagram showing placement of wall plates (01, 02) and marking of hole positions.
3. Drill 8 Holes: Diagram showing drilling into drywall and wood stud. Drill bit sizes: 2 3/8" (60mm) for drywall, Ø5/32" (4mm) for wood stud.
4. Tap Wall Anchors In: Diagram showing insertion of wall anchors [A2] into the drilled holes.
5. Secure the Wall Plates: Diagram showing attachment of wall plates (01, 02) using Lag Screws [A1] and a screwdriver. Ensure the level (06) is used. Diagrams show correct and incorrect tightening of screws.

Go to Step 5 on Page 14.

Option B: For Solid Concrete Installation

Diagram showing minimum concrete thickness of 8" (203mm).

Tools Needed (Not Included): Electric Drill, Pencil, 5/16" (8mm) Concrete Drill Bit, Hammer, Phillips Screwdriver.

WARNING: Avoid the risk of personal injury or property damage! Tighten the lag screws [A1] only until they are pulled firmly against the wall plate (DO NOT overtighten). Do not use a drill; only use a Phillips screwdriver. Use wall anchors [A2] for this mounting option. Mount the wall plate directly on the concrete surface.

Diagram showing a wall anchor [A2] for concrete installation.

1. Mark 8 Hole Positions: Diagram showing placement of wall plates (01, 02) and marking of hole positions.
2. Drill 8 Holes: Diagram showing drilling into concrete. Drill bit size: 2 3/8" (60mm) for concrete.
3. Tap Wall Anchors In: Diagram showing insertion of wall anchors [A2] into the drilled holes.
4. Secure the Wall Plates: Diagram showing attachment of wall plates (01, 02) using Lag Screws [A1] and a screwdriver. Ensure the level (06) is used. Diagrams show correct and incorrect tightening of screws.

STEP 5 Verify Wall Plates are Firmly Mounted

Diagram showing how to test the mounted wall plates by pulling down on them. A green checkmark indicates correct mounting, while a red cross indicates incorrect mounting.

STEP 6 Hang the TV

Diagram showing how to attach the TV brackets to the TV.

Diagram showing two people lifting and hanging the TV onto the mounted wall plates. Ensure the brackets click into place.

HEAVY! You may need assistance with this step.

Diagram showing the final connection of the TV to the wall mount, with a 'Press' indicator.

Tip: The kickstand (G) can be folded up for easier cable access.

STEP 7 Level Adjustment

Diagram showing how to adjust the TV's level. Slightly lift to unlock, then level your TV using the adjustment screws and the level (06).

Diagrams showing locked and unlocked states of the mount.

STEP 8 How to Remove the TV

Note: Before removing the TV, disconnect all cables, then gently rock the TV from side to side to unlock it.

Diagram showing how to unlock and remove the TV from the wall mount by pulling downwards.

HEAVY! You may need assistance with this step.