Manuals+

Perlegear PGMTK1 Instruction Manual

Model: PGMTK1 Rev01

Product Overview

This document provides instructions for the Perlegear PGMTK1 Tilting TV Wall Mount.

Languages Included: English, German, French, Spanish, Italian

Compatibility Check (Before Getting Started)

  1. VESA Compatibility: Ensure your TV's VESA pattern is greater than or equal to 75 x 75mm (3 x 3 inches) or less than or equal to 400 x 400mm (15.7 x 15.7 inches). If not, this mount is not compatible.

    Diagram: Shows a TV with W and H dimensions and VESA hole pattern. Options: Yes - Perfect! / No - This mount is NOT compatible.

  2. Weight Capacity: Verify your TV weighs less than 115 lbs (52kg). If it weighs more, this mount is not compatible.

    Diagram: Shows a TV icon with weight indicator 115 lbs (52kg). Options: Yes - Perfect! / No - This mount is NOT compatible.

  3. Wall Type Verification: Ensure your wall type is suitable for mounting. CAUTION: DO NOT install on drywall alone. Suitable wall types include wood studs (with drywall) and solid concrete/brick walls.

    Diagram: Illustrates wood studs with drywall and solid concrete/brick walls. Shows maximum stud depth of 16" (406mm).

  4. Tools Needed (Not Included):

    • For Wood Stud Walls: Stud Finder, Awl, 5/32" (4mm) Wood Drill Bit, Electric Drill, Pencil, Phillips Screwdriver, 7/16" (11mm) Socket Wrench.
    • For Solid Concrete or Brick Walls: Hammer, 3/8" (10mm) Concrete Drill Bit, Electric Drill, Pencil, Phillips Screwdriver, 7/16" (11mm) Socket Wrench.

    Diagrams: Show illustrations of the required tools for each wall type.

Included Hardware

Washers: M4/M5 [B1] x 4, M6/M8 [B2] x 4

Spacers: L2.5mm [F1] x 8, L10mm [F2] x 4, L22mm [F3] x 4

Bolts: M4 x 30mm [C] x 4, M6 x 35mm [D] x 4, M8 x 45mm [E] x 4

Lag Screw: ST1/4 x 2 3/4" [A1] x 4

Wall Anchor: [A2a] x 4

Level: [A2b] x 1

Mounting Components: Wall Plate [01] x 1, TV Bracket [02] x 1, TV Bracket [03] x 1

Diagrams: Illustrate each hardware component with its corresponding label and quantity.

Installation Steps

Step 1: Attach TV Brackets to TV

Select the appropriate TV bolts (M4, M6, or M8) by hand-threading them into the TV's rear inserts. A minimum of 4-5 turns is required. Do not overtighten.

Diagrams: Show the three bolt sizes (M4, M6, M8) and indicate correct and incorrect insertion methods.

Select spacers [F1], [F2], and [F3] if needed to ensure a flush fit against the TV back.

Diagrams: Illustrate the use of spacers between the TV bracket and the TV back.

Secure the TV brackets [02] and [03] to the TV using the selected bolts (C/D/E), washers (B1/B2), and spacers (F1/F2/F3).

Diagram: Shows the TV brackets being attached to the TV with bolts and washers.

Step 2: Mount the Wall Plate on the Wall

A. Wood Studs Option:

Locate wood studs using a stud finder. Ensure the wall studs are at least 16" (406mm) apart. Drill pilot holes using the 5/32" (4mm) wood drill bit. Attach the wall plate [01] to the wall studs using lag screws [A1]. Use the level [A2b] to ensure the plate is horizontal.

Diagrams: Illustrate the process of locating studs, drilling pilot holes, and mounting the wall plate with lag screws.

B. Solid Concrete and Brick Walls Option:

For solid concrete or brick walls, drill holes using the 3/8" (10mm) concrete drill bit. Insert wall anchors [A2a] into the drilled holes. Attach the wall plate [01] to the wall using lag screws [A1] through the wall anchors. Use the level [A2b] to ensure the plate is horizontal.

Diagrams: Show drilling into concrete/brick walls, inserting anchors, and mounting the wall plate.

Step 3: Verify that the Mount is Firmly Mounted

Gently pull on the mounted wall plate to ensure it is securely attached to the wall. Test with a weight of 115 lbs (52kg) if possible.

Diagrams: Show a hand pulling on the wall plate and a weight indicator.

Step 4: Adjust the Tilt Angle of the TV

Use a Phillips screwdriver to adjust the tilt angle of the TV by turning the adjustment screw (T). Lock the desired angle in place.

Diagram: Shows a Phillips screwdriver adjusting a screw on the TV bracket to set the tilt angle.

Step 5: Hang the TV on the Wall Plate

Carefully lift the TV with the attached brackets and hang it onto the wall plate. Ensure the safety pull strings are engaged to lock the TV in place.

Diagrams: Illustrate lifting the TV and hooking it onto the wall plate, with a close-up of the locking mechanism.

Step 6: TV Removal

To remove the TV, pull the safety pull strings to unlock the TV from the wall plate. Carefully lift the TV off the wall plate.

Diagrams: Show the process of disengaging the safety pull strings and removing the TV.

Important Safety Information

NOTE: Not all hardware included in this package will be used.

CAUTION:

WARNING: This product contains small parts that may pose a choking hazard.

Contact Information

Customer Support:

Website: www.perlegear.com

Authorized Representatives:

Manufacturer: BESTQI INNOVATION (HONG KONG) TECHNOLOGY CO., LIMITED

Manufacturer Address: FLAT/RM 185 G/F HANG WAI IND CENTRE 6 KIN TAI ST TUEN MUN NT

Models: PGMTK1-E, PGMTK1-U, PGMTK1-E TV Wall Bracket, PGMTK1-E, TV Wall Bracket, Wall Bracket, Bracket
C1Lfk7it1ZL Adobe Illustrator 25.0 (Windows) iLovePDF

Related Documents

Preview Perlegear PGLT2 Tilting TV Wall Mount Instruction Manual
Comprehensive instruction manual for the Perlegear PGLT2 tilting TV wall mount. Includes installation steps, safety information, parts list, and troubleshooting for various TV types and wall constructions.
Preview PERLEGEAR PGLT5 Tilting TV Wall Mount Instruction Manual
Comprehensive instruction manual for the PERLEGEAR PGLT5 tilting TV wall mount. Covers safety information, compatibility checks, parts list, step-by-step installation for various wall types, TV attachment, tilt adjustment, removal, and FAQs. Designed for TVs up to 82 inches and 60kg, supporting VESA patterns up to 600x400mm.
Preview Perlegear PGLF8 Full Motion TV Wall Mount Installation Guide
Comprehensive instruction manual for the Perlegear PGLF8 Full Motion TV Wall Mount. Learn how to safely install and adjust your TV mount for TVs up to 132 lbs, with detailed steps for wood stud and concrete wall installations.
Preview Perlegear TV Wall Mount Instruction Manual PGMFK6
Instruction manual for the Perlegear PGMFK6 TV Wall Mount, covering safety information, weight restrictions, VESA pattern compatibility, wall construction verification, tools needed, parts list, and step-by-step installation and adjustment instructions.
Preview Perlegear PGLF6 Full-Motion TV Wall Mount Instruction Manual
Comprehensive instructions for installing and using the Perlegear PGLF6 full-motion TV wall mount, designed for 32-85 inch TVs up to 60 kg with VESA compatibility up to 600 x 400 mm.
Preview Perlegear TV Wall Mount Frequently Asked Questions (FAQ)
Find answers to common questions about Perlegear TV wall mounts, including VESA patterns, wall types, installation challenges, and troubleshooting steps.
Preview PERLEGEAR PGLF7 Full-Motion TV Wall Mount - Installation Manual
Comprehensive installation manual for the PERLEGEAR PGLF7 Full-Motion TV Wall Mount. Includes safety information, parts list, step-by-step assembly instructions, and FAQs for mounting your TV securely.
Preview Perlegear PGMFK3 Full-Motion TV Wall Mount Instruction Manual
Comprehensive instruction manual for the Perlegear PGMFK3 full-motion TV wall mount, covering VESA compatibility, load capacity, wall type selection, installation steps, and TV mounting. Includes safety guidelines and parts identification.