ADJ Micro Sky

General Introduction

Unpacking

Thank you for purchasing the Micro Sky by ADJ Products, LLC. Every Micro Sky has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact. In the event damage has been found or parts are missing, please contact our toll-free customer support number for further instructions. Please do not return this unit to your dealer without contacting customer support first.

Introduction

The Micro Sky is a portable green laser that produces a brilliant "liquid sky" effect that can be projected on a ceiling or wall. The Micro Sky is a stand-alone fixture with 2 operating modes: sound active mode and auto mode. The Micro Sky's compact, lightweight case design makes it ideal for mobile entertainers, bands, night clubs, and bars. For best results, use fog or special effects smoke to enhance the beams projections.

Customer Support

ADJ Products, LLC provides a toll-free customer support line to provide set-up help and to answer any questions should you encounter problems during your set-up or initial operation. You may also visit us on the web at www.adj.com for any comments or suggestions. For service-related issues, please contact ADJ Products, LLC. Service hours are Monday through Friday, 8:00 a.m. to 4:30 p.m. Pacific Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: support@adj.com

Warnings

❗ To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

❗ Caution! There are no user-serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void your manufacturer's warranty. In the unlikely event your unit may require service, please contact ADJ Products, LLC customer support.

PLEASE recycle the shipping carton whenever possible.

General Instructions

Please carefully read and understand the instructions in this manual thoroughly before attempting to operate this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit for future reference.

Important Caution

CAUTION IMPORTANT! When installing this projector, make sure that it is mounted in a manner that prevents the audience from looking directly into the beam, and the beam from striking the audience.

Features

• 30mW (532nm) Green Laser
• 25 Laser Patterns & 15 Built-In Programs
• 2 Operating Modes - Sound Active Mode & Auto Mode
• RF Wireless Remote Control (Included)
• Dual Hanging Bracket

Warranty Registration

The Micro Sky carries a 90-day limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items, whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Please contact ADJ Products, LLC customer support for an R.A. number.

Safety Precautions

General Safety

❗ To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

Do not spill water or other liquids into or on to your unit.

Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short. Do not attempt to operate this unit if the power cord has been frayed or broken.

Disconnect from main power before making any type of connection.

Do not remove the cover under any conditions. There are no user-serviceable parts inside.

Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6" (15cm) between this device and a wall.

Do not attempt to operate this unit if it becomes damaged.

This unit is intended for indoor use only; use of this product outdoors voids all warranties.

During long periods of non-use, disconnect the unit's main power.

Always mount this unit in a safe and stable manner.

Power cords should be routed so they are not likely to be walked on, pinched by items placed upon or against them.

Cleaning

The fixture should be cleaned only as recommended by the manufacturer. See page 11 for cleaning details.

Heat

The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.

Servicing

The fixture should be serviced by qualified service personnel when:

• A. The power-supply cord or the plug has been damaged.
• B. Objects have fallen, or liquid has been spilled into the unit.
• C. The unit has been exposed to rain or water.
• D. The unit does not appear to operate normally or exhibits a marked change in performance.

Laser Safety Precautions

DANGER: VISIBLE LASER RADIATION - AVOID DIRECT EYE EXPOSURE

LASER DIODE WAVELENGTH: 635~650 nm

Max Output: <4.9mW

Class IIIa Laser Product

Laser Warnings and Safety

NON-INTERLOCKED HOUSING WARNING

The Micro Sky contains high power laser devices internally. Do not open the laser housing, due to the potential exposure to unsafe levels of laser radiation. The laser power levels, if the unit is opened, can cause instant blindness, skin burns and fires.

STOP AND READ ALL LASER SAFETY DATA, OPERATION INSTRUCTIONS AND LASER SAFETY

The light source emitted from this product can potentially cause eye injury if not set up and used properly. The light source emitted from a laser is very different from any other light sources with which you may be aware of. Laser light is thousands of times more concentrated than any light from any other kind of light source. This concentration of light can cause instant eye injuries, primarily by burning the retina (the back of your eyeball containing cells that are sensitive to light). Even if you cannot feel “heat” from a laser beam, it can still potentially injure or blind you or your audience. Even very small amounts of laser beam light are potentially hazardous even at long distances. Laser eye injuries can be sustained faster than you can blink.

Do not think that because this laser splits the laser beam into hundreds of beams and that the laser beam is scanned out in high speed, that an individual laser beam is safe for eye exposure. This laser uses dozens of milliwatts of laser power (Class 3B levels internally) before it splits into multiple beams (Class 3R levels). Many of the individual beams are potentially hazardous to the eyes.

Do not assume that because the laser light is moving, it is safe. This is not true. Nor, do the laser beams always move. Since eye injuries can occur instantly, it is critical to prevent even the smallest possibility of any direct eye exposure. In the laser safety regulation, it is not legal to aim Class 3R lasers in areas where people can get exposed. This is true even if it is aimed below people's faces, such as on a dance floor.

Do not operate the laser without first reading and understanding all safety and technical data in this manual.

Always set up and install all laser effects so that all laser light is at least 3 meters (9.8 feet) above the floor on which people can stand.

After setting up, and before public use, test laser to ensure proper function. Do not use if any defect is detected. Do not use if laser emits only one or two laser beams rather than dozens/hundreds, as this could indicate damage to the diffraction grating optic, and could allow emission of higher laser levels above Class 3R.

Do not point lasers at people or animals. Never look into the laser aperture or laser beams.

Do not point lasers in areas where people can potentially get exposed, such as uncontrolled balconies, etc.

Do not point lasers at highly reflective surfaces, such as windows, mirrors and shiny metal. Even laser reflections can be hazardous.

Never point a laser at aircraft; this is a federal offense.

Never point un-terminated laser beams into the sky.

Do not expose the output optic (aperture) to cleaning chemicals.

Do not use the laser if the laser appears to be emitting only one or two beams.

Do not use the laser if the housing is damaged, the housing is open, or if the optics appear damaged in any way.

Never open the laser housing. The high laser power levels inside of the protective housing can start fires, burn skin and will cause instant eye injury.

Never leave this device running unattended.

The operation of a class 3R laser show is only allowed if the show is controlled by a skilled and well-trained operator, familiar with the data included in this manual.

The legal requirements for using laser entertainment products vary from country to country. The user is responsible for the legal requirements at the location/country of use.

Always use proper lighting safety cables when hanging lights and effects overhead.

Control Panel

Diagram Description

The control panel features the following:

• 1. Main Input: Connect to main power.
• 2. Power Switch: Turns On/Off the power.
• 3. Fan: Cools the unit.
• 4. Speed: Used to adjust the speed under Auto mode (slow to fast).
• 5. Remote code: To activate your remote or erase remote code.
• 6. Microphone: Receives the sound to control the unit.
• 7. Auto/Sound switch button: Press to switch between Auto-play or Sound active mode.

Auto mode: The unit will run at a slow or fast speed.

Operation

Mounting Caution

CAUTION IMPORTANT! When installing this projector, make sure that it is mounted in a manner that prevents the audience from looking directly into the beam, and the beam from striking the audience.

Operating Modes

• Sound Active Mode: The fixture will react to sound, chasing through the built-in programs.
• Auto Play: This function runs automatically through all of the unit's patterns.

Sound Active Mode

This mode allows the unit to run to the beat of the music.

1. Press the Auto/Sound button. When the red indicator light located on the front of the unit turns off, but flashes to the beat of the music, the unit is in sound active mode.

Auto Play Mode

This is Auto Play mode.

1. Press the Auto/Sound button. When the red indicator light flashes rapidly, the unit is in fast auto mode. When the indicator light flashes slowly, the unit is in slow auto mode.
2. Use the speed knob to control the speed of the mode.

Remote Control

Use the included remote to control various functions. Please see below for button control.

Note: This remote control code has been set for this laser, so that the laser can be controlled out of the box. If this code happens to get erased, the remote will not work with the unit. Please see below to reset the code and link the laser to the remote again.

Button Functions

• A Button: Use this button to switch between Auto Play and Sound Active. When the red indicator light flashes rapidly, the unit is in fast auto mode. When the indicator light flashes slowly, the unit is in slow auto mode. When the red indicator light located on the front of the unit turns off, but flashes to the beat of the music, the unit is in sound active mode.
• B Button: Use this button to Blackout the unit.
• C Button: Use this button to scroll and select patterns.
• D Button: Use this button to select a show.

Remote Activation & Erase

Erase Remote Code

Using a small utensil, carefully press and hold the Remote Code button (5) for at least 7 seconds.

Activating and Linking Remote

This action will set the code to link the laser to your remote. You can link more than one laser to a remote.

Using a small utensil, carefully press and hold the Remote Code button (5) for at least 3 seconds. Try to control the unit with the remote. If the unit can be controlled, setting the code was successful. If it does not control the unit, try again.

Cleaning

Fixture Cleaning

Due to fog residue, smoke, and dust, cleaning the internal and external lenses should be carried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.
2. Clean the external optics with a microfiber cloth every 20 days.
3. Always be sure to dry all parts completely before plugging the unit back in.

Cleaning frequency depends on the environment in which the fixture operates (i.e., smoke, fog residue, dust, dew). In heavy use, we recommend cleaning on a monthly basis. Periodic cleaning will ensure longevity and crisp beam output.

Trouble Shooting

No Laser Output from the Unit

1. Be sure you have connected your unit into a standard wall outlet.
2. In cold temperature situations, it might take the laser a little longer to produce output. It can take up to 3-5 minutes for the laser to produce a beam. This is due to the laser diode, which is very sensitive.

Unit Does Not Respond to Sound

1. Low frequencies (bass) should cause the unit to react to sound. Tapping on the microphone, quiet or high-pitched sounds may not activate the unit.

Manufacturer's Limited Warranty

Warranty Terms

ADJ Products, LLC warrants its products to the original purchaser to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase. This warranty is valid only if the product is purchased within the United States of America. The owner must establish the date and place of purchase by acceptable evidence. For warranty service, obtain a Return Authorization number (RA#) from ADJ Products, LLC Service Department (800-322-6337). Ship product freight pre-paid to the ADJ Products, LLC factory. ADJ Products, LLC will pay return shipping charges within the United States if repairs are covered by warranty.

This warranty is void if the serial number is altered or removed, if the product is modified in a way that affects reliability, if repaired or serviced by anyone other than the ADJ Products, LLC factory without prior written authorization, or if damaged due to improper maintenance.

This is not a service contract. ADJ Products, LLC will replace defective parts with new or refurbished parts and cover repair labor expenses. The sole responsibility of ADJ Products, LLC is limited to repair or replacement at its discretion. Products manufactured after August 15, 2012, bear identifying marks.

ADJ Products, LLC reserves the right to make design changes without obligation to include them in previously manufactured products.

No warranty, expressed or implied, is given for accessories supplied with the product. Implied warranties of merchantability or fitness are limited to the warranty period. ADJ Products, LLC is not liable for direct or consequential loss or damage arising from use or inability to use this product.

This warranty supersedes all prior warranties and written descriptions.

Warranty Periods

• Lighting Products: 1-year (365 days) Limited Warranty (excluding LED, Laser Products, and lamps).
• Laser Products: 90-Day Limited Warranty.
• L.E.D. Products: 3-year (1095 days) Limited Warranty (excluding motors, PCB boards, power supplies (1-year), and batteries (180-day)). Only the L.E.D.s carry a 3-year warranty.

Specifications

Auto Sensing Voltage: This fixture contains an automatic voltage switch, which will auto-sense the voltage when it is plugged into the power source.

Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.

Contact Information

US Office

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: 323-582-2650 / Fax: 323-725-6100

Web: www.adj.com / E-mail: info@adj.com

Europe Office

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands

E-mail: service@adj.eu / Web: www.adj.com

Tel: +31 45 546 8500 / Fax: +31 45 546 85 99

Follow Us

Facebook: facebook.com/americandj

Twitter: twitter.com/americandj

YouTube: youtube.com/adjlighting