Welcome and Important Information
Thank you for purchasing a Babyletto nursery product! To ensure safe use of your product, please follow these assembly instructions closely. If you are missing parts or have any questions, please visit our website at www.babyletto.com/support.
For assembly, use the Allen wrench if it is included in the hardware box. We also recommend using a Phillips head screwdriver (not included) to complete assembly. Please do not substitute parts or use power screwdrivers. Due to the nature of our materials, some variation in color, grain, or texture is to be expected.
We hope you and your growing family enjoy our product.
With thanks, Babyletto
Note: Two people are needed to assemble this crib. ???
Tools Needed (not included): ? Phillips screwdriver
Assembly Instructions
Step 1
Assemble the base frame. Connect parts J and K using hardware H5, H7, and H13. The diagram shows four connection points, each using two H5 dowels, one H7 lock washer, and one H13 bolt. An Allen wrench (H12) is shown for tightening. A circular arrow indicates tightening. The quantity 'X4' indicates this is done at four locations.
Parts used: J, K
Hardware used: H5 (x8), H7 (x4), H13 (x4)
Note: DO NOT OVERTIGHTEN. NE PAS TROP SERRER. ⚠️
Step 2
Attach the feet (F) to the base frame rails (J). Insert dowels (H5) into the frame rails and then attach the feet (F). The diagram shows four feet being attached to the long base frame rails (J). The quantity 'X4' indicates this is done at four locations.
Parts used: F, J
Hardware used: H5 (x8)
Step 3
Connect the base frame rails (J) to the side panels (implied). The diagram shows two base frame rails (J) being attached to a structure using bolts (H4) and lock washers (H7). A circular arrow indicates tightening. The quantity 'X4' indicates this is done at four locations.
Parts used: J
Hardware used: H4 (x4), H7 (x4)
Note: DO NOT OVERTIGHTEN. NE PAS TROP SERRER. ⚠️
Step 4
Attach the base frame rails (J, K) to the side panels (implied). The diagram shows wood dowels (H5) being inserted into the ends of the frame rails (J, K) and then connecting them to the side panels. The quantity 'X8' indicates this is done at eight locations.
Parts used: J, K
Hardware used: H5 (x8)
Step 5
Attach the front/back panel (A) to the base frame (J). The diagram shows wood dowels (H5) being inserted into the base frame (J) and then connecting the front/back panel (A) to it. The quantity 'X3' indicates this is done at three locations.
Parts used: A, J
Hardware used: H5 (x3)
Step 6
Attach the front/back panel (A) to the base frame (J). The diagram shows bolts (H4) and lock washers (H7) being used to secure the panel. An upward arrow indicates insertion. The quantity 'X2' indicates this is done at two locations.
Parts used: A, J
Hardware used: H4 (x2), H7 (x2)
Note: DO NOT OVERTIGHTEN. NE PAS TROP SERRER. ⚠️
Step 7
Attach the side panels (B-2) to the front/back panels (A) and base frame (J, K). The diagram shows Allen head bolts (H1) and lock washers (H7) being used for connection. The quantity 'X8' indicates this is done at eight locations.
Parts used: A, B-2, J, K
Hardware used: H1 (x8), H7 (x8)
Note: DO NOT OVERTIGHTEN. NE PAS TROP SERRER. ⚠️
Step 8
Attach the side panels (B-2) to the front/back panels (A) and base frame (J, K). The diagram shows bolts (H4) and lock washers (H7) being used for connection. The quantity 'X4' indicates this is done at four locations.
Parts used: A, B-2, K
Hardware used: H4 (x4), H7 (x4)
Note: DO NOT OVERTIGHTEN. NE PAS TROP SERRER. ⚠️
Step 9
Complete the main crib structure. The diagram shows the side panels (B-2) being attached to the front/back panels (A) and base frame (J, K) using Allen head bolts (H1) and lock washers (H7). The quantity 'X4' indicates this is done at four locations.
Parts used: A, B-2
Hardware used: H1 (x4), H7 (x4)
Note: DO NOT OVERTIGHTEN. NE PAS TROP SERRER. ⚠️
Step 10
Install the mattress support (G-1) using Allen head bolts (H3). The diagram shows four bolts being used to secure the mattress support to the side panels (A, B-2). The quantity 'X4' indicates this is done at four locations.
Parts used: G-1
Hardware used: H3 (x4)
Important:
- Make sure the mattress support IV (G-1) is installed FLAT SIDE UP.
- Make sure the mattress support IV (G-1) is level.
Note: DO NOT OVERTIGHTEN. NE PAS TROP SERRER. ⚠️
Age/Size Guidance: Suitable for 0-1 years old and 1-2 years old.
Step 11
Finalize the crib structure. The diagram shows securing panels using hardware H7 and H1 (quantity X4) and H7 and H4 (quantity X2). The 'Finish' label indicates completion.
Hardware used: H7 (x4), H1 (x4), H4 (x2)
Note: DO NOT OVERTIGHTEN. NE PAS TROP SERRER. ⚠️
Final Steps:
- KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE.
- Recheck all screws and bolts to be sure they are fastened securely. Do not overtighten.
- Before using your crib, please read all cautionary statements on the insert sheet.
Toddler Bed Conversion Assembly
The crib can be converted into a toddler bed. All necessary parts and hardware are supplied with the crib.
Step 1 (Toddler Bed Conversion)
Ensure the mattress support IV (G-1) is installed at the lowest level. The diagram shows this configuration.
Parts used: G-1
Step 2 (Toddler Bed Conversion)
Attach the toddler bed conversion kit components. The diagram shows using hardware H2 and H7 to connect parts I to the main structure. The quantity 'X4' indicates this is done at four locations.
Parts used: I
Hardware used: H2 (x4), H7 (x4)
Note: DO NOT OVERTIGHTEN. NE PAS TROP SERRER. ⚠️
Finish: Terminé
Warranty, Storage, and Care
One Year Limited Warranty
Babyletto will replace any missing parts at the time of purchase or any defective item within a one year period from the date of original purchase. Please keep your receipt so that we may process your warranty request. This warranty only covers new units with original packaging and ownership, and is not transferable. It does not cover any used, secondhand or demo models.
This warranty does not cover any damaged or defective parts that result from installation and assembly, normal wear and tear, abuse, negligence, improper use or alteration to the finish, design, and hardware of the crib. The specific legal rights of this warranty may vary from state to state. Some states do not allow any exclusion or limitation of incidental damages. Some states do not allow limitation on how long an implied warranty lasts.
Storage
Pine woods exchange moisture with the air adjusting to major changes in room temperature and humidity. Therefore, it is best to place your furniture away from heating or air-conditioning vents. Sunlight is not friendly to solid wood furniture and prolonged direct exposure to harsh sunlight can discolor the finish. Be careful not to place your furniture in direct sunlight for extended periods of time. As with all your fine furniture, blot up spills immediately.
Care and Cleaning
Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning. Clean with mild soap on a damp, soft rag. Rinse and dry thoroughly. If you ever refinish this furniture, be sure to use only a non-toxic finish specified for children's products. If you choose to refinish this furniture, the warranty will be voided.