Bulldog EVC300 Wi-Fi Connectivity Guide

Connecting your Bulldog EVC300 controller to your Wi-Fi network using the eWeLink app.

Basic Controller Functions

The Bulldog EVC300 controller allows you to open or close your Bulldog Valve by pressing and releasing a button. Holding this button for 7 seconds and then releasing it cycles through the Wi-Fi pairing modes.

Wi-Fi Pairing Mode Indicators (Blue LED):

Solid: Controller is in normal operation and connected to Wi-Fi.
Flash then long pause: Controller is in normal operation but not connected to Wi-Fi.
Three flashes then a pause: Controller is ready for Quick Pairing.
Constant fast flashes: Controller is ready for Compatible mode.
To start over: Unplug and re-plug the controller's power.

Button Functions:

Press to stop alarm sounding.
Press to pair sensors and remote stop buttons.

App Control

Download and install the eWeLink App.

Note: Your device must be connected to a Wi-Fi network that utilizes a 2.4GHz band and WPA2 security.

Pairing Method 1: Quick Pairing

Note: Turn your mobile data off as it may interfere with quick pairing.

Hold the controller's main button for 7 seconds and release to cycle the Bulldog Controller into Quick Pairing Mode. This is indicated by the blue LED flashing 3 times followed by a pause. (Refer to Basic Controller Functions)
On your eWeLink app, tap the "Add" or "+" button.
Enter your Wi-Fi password and tap on the "Next" button.
Wait up to 30 seconds for the device to connect.
Once your Bulldog device is found, tap the "Next" button.
When completed, you can change the name of the Bulldog device and then tap on the "Done" button.
Connection Status: If connected, proceed to the "Once Connected to App" section. If not connecting, proceed to "Pairing Method 2".

Pairing Method 2: Compatible Mode Pairing

Note: Turn your mobile data off as it may interfere with Compatible Mode pairing.

On your eWeLink app, click the "add" or "+" button.
Confirm your Wi-Fi network and password, then tap on ‘More pairing options.’
Press and hold the controller's main button to cycle the Bulldog Controller into Compatible Mode. This is indicated by the blue LED constant fast flashing. (Refer to Basic Controller Functions)
Press the "Next" button.
Re-confirm your Wi-Fi information and tap "Next".
Wait up to 30 seconds for your controller to appear.
- If the "ITEAD Device appears": select it and move to the next step.
- If the "Device does not appear": confirm that your controller is in Compatible Mode, indicated by the Blue LED flashing quickly and constantly.
Enter your device settings by pressing the "Go to connect" button, or open your device's settings app.
In settings, connect your device Wi-Fi to the Bulldog Controller hotspot. The default password is "12345678".
When prompted that "Internet may not be available", press the "Connect only this time" button.
Return to the eWeLink app, which will present a loading screen.
After connecting, move to the "Once Connected to App" section.

Once Connected to App

Rename your Bulldog controller appropriately (e.g., "Water Main" or "Bulldog Valve Robot").
Click your new device in the "Home" screen.
Click the three horizontal dots in the top right corner.
Scroll down and press the "Device Settings" button.
Under "Power-on State", select "Last state" and save.
Turn on Push Notifications and return to your "Home" screen.
Your Bulldog Controller is now paired and can be toggled on and off in the app.

Support

Econet Support Email: support@econetcontrols.com

EcoNet Support Phone: (888) 320-9188

Additional Support Page Link: https://www.econetshop.com/index.php/support/

eWeLink Pairing Video Link: https://www.youtube.com/watch?v=WfbXw3lg11w

Sonoff Bridge Support Link: https://www.econetshop.com/PDF/SonoffBridgeKit.pdf

Document Version: Bulldog EVC300 WiFi Connectivity Guide - eWeLink - Rev_C