Bulldog-JW Valve Robot, Model EVC300 Control Module
Quick Start Guide
The Bulldog-JW Starter Kit is a Leak Detection & Prevention Solution that “Just Works".
- Install the Bulldog motor assembly over your water shutoff ball valve (See Mounting/Valve Install Guide).
- Connect the Motor Assembly to the Control Module.
- Plug in the AC Adapter and connect it to the Control Module.
- Position the Sensors in leak-sensitive locations.
- Done!
Visual Description: The Bulldog-JW Starter Kit includes a motor assembly attached to a water shutoff valve, a control module, an AC power adapter, and three wireless leak sensors. The motor assembly connects to the control module, which is powered by the AC adapter. The leak sensors are designed to be placed in leak-sensitive locations.
Visual Description: The EcoNet Controls module features several buttons: an 'Alarm Reset Button' (labeled as Speaker), a 'Leak Sensor Pairing Button' (Green button), a 'Valve Open/Close Button', and a 'WIFI Pairing Button'.
Leak Alarm Reset
- Click On/Off Reset Button (Speaker)
- Click On/Off Valve Open/Close Button (once or twice)
Adding ELS100 Leak Sensors
- The Green button is the Leak Sensor Pairing Button (indicated by a green indicator with a directional arrow).
- Adding/Pairing Leak Sensors: Click the Green button On/Off, then activate the leak sensor for 2 Beep Cycles.
- Click Alarm Reset, repeat the above process for additional Leak Sensors.
Exclude All Leak Sensors
- All paired Leak Sensors can be removed (Excluded) by holding the green button for approximately 5 seconds until a red blink acknowledgment is received.
WIFI Pairing to eWeLink App
- Install, set up an account, and log in to the eWeLink App.
- The Valve Icon is the WIFI Pairing Button.
- Blue LED Status: Slow Single Blink, pause, indicates not paired and not broadcasting.
- Blink, blink, blink, pause, repeat, indicates ready to be paired (Quick Pairing mode).
- A 2.4GHz Network is required, and your Smart Phone should be connected to this 2.4GHz Network.
- If the device is not in pairing mode, hold the Valve Icon button for approximately 4 seconds to set it to pairing mode.
- On your smartphone, in the eWeLink App, use the "+" icon and follow the instructions for "Quick Pairing".
- The App should acknowledge successful pairing within 20-90 seconds.
- Rename the Bulldog valve appropriately (e.g., “Water Main”).
- In the device settings menu (select device, then the settings menu represented by three dots), update "Power-on State" to "Last state".
- In device settings, turn on “Push Notifications” to receive notices of valve open or closed (On/Off).
- In device settings, update “Current Version”, if required.
LED Status
| LED Status | Steady Slow Blink | 3 Blink, Pause | Solid On | Solid Off |
|---|---|---|---|---|
| Blue LED | Not WIFI Paired | Waiting to be paired | WIFI Paired | |
| Red LED, Valve Icon | Valve Open | Valve Closed | ||
| Green LED (Speaker) | Green, System Armed or Red - in alarm state, Speaker Beeping |
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
*RF warning for Mobile device: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
