Mylift High Chair

Parts List

Before assembling the product, check that you have all the following parts:

• Seat Back x 1
• Height Bracket x 2
• Tray Insert x 1
• Tray x 1
• Upper Frame Assembly x 2
• Seat Back Hinge Rod x 1
• Seat Base x 1
• Crotch Retainer x 1
• Screw (3.5 mm x 10) x 4
• Front Leg x 1
• Rear Leg x 1
• Footrest x 1
• Caster (with brake) x 2
• Front Wheel x 2
• Seat Pad x 1

Important Safety Warnings

Failure to follow these warnings and instructions could result in serious injury or death.

Prevent serious injury or death from falls or sliding out. Always secure child in the restraint. NEVER leave child unattended.

The child should be secured in the high chair at all times by the 5-point restraining system, either in the reclining, semi-reclining or upright position. The tray is not designed to hold the child in the chair. It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted. See page 19 for instructions on proper use of restraint system.

• Other accessory items may change the balance of the high chair and cause hazardous unstable conditions; use approved Baby Trend toys.
• Be certain the high chair is fully erect and latched in the open position before allowing the child near the high chair.
• Use of the high chair with a child weighing more than 40 pounds (18.14 kg) will cause excessive wear and stress on the high chair.
• The maximum weight that can be carried in the basket is 5 pounds (2.26 kg). Excessive weight may cause a hazardous unstable condition to exist.
• NEVER allow your high chair to be used as a toy.
• NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact Baby Trend Customer Service at 1-800-328-7363 for replacement parts, repair or instructions. NEVER substitute parts.

[STOP] [ALTO] [ARRÊT]

Assembly Instructions

Assembly by an adult is required. Please follow these instructions carefully and keep them for future reference.

1. Step 1: Prepare the Seat Base

   Place the Seat Base on a flat surface as shown in Figure 1. Figure 1 shows the Seat Base.

2. Step 2: Attach Seat Back to Seat Base

   Join the Seat Back to the Seat Base using the Seat Back Hinge Rod as shown in Figure 2. To install the hinge rod, press down on the hinge rod retainer and insert the rod into the hinge from right to left. Figure 2 illustrates joining the Seat Back to the Seat Base using the Seat Back Hinge Rod.

3. Step 3: Attach Height Brackets

   Slide the left and right sides Height Bracket onto the Seat Base (as shown in Figure 3a). Snap the brackets into place (as shown in Figure 3b). Figure 3a shows the Height Brackets being slid onto the Seat Base, and Figure 3b shows them snapped into place.

4. Step 4: Attach Footrest

   Slide the Footrest onto the Seat Base as shown in Figure 4. Snap the Footrest into place. Figure 4 shows the Footrest being attached to the Seat Base.

5. Step 5: Attach Right Side Upper Frame Assembly

   Insert the front tube of the right side Upper Frame Assembly into the Height Bracket (as shown in Figure 5). The front tube is distinguished from the rear tube by the array of holes located on its backside. Figure 5 shows the front tube of the Upper Frame Assembly being inserted into the Height Bracket.

6. Step 6: Secure Right Side Upper Frame Assembly

   Squeeze the Red Release Handle and push the tube through the Height Bracket until it locks on the highest position (as shown in Figure 6). Figure 6 illustrates securing the Upper Frame Assembly.

7. Step 7: Attach Left Side Upper Frame Assembly

   Repeat Steps 5 and 6 for the left side Upper Frame Assembly (as shown in Figure 7). Figure 7 shows the left side Upper Frame Assembly being attached.

8. Step 8: Insert Front Legs

   Insert the front legs into the ends of the front tube of both the right and left Upper Frame Assemblies (as shown in Figure 8). Ensure the push buttons align with the holes on the ends of the Upper Frame Assemblies and are engaged before use. Figure 8 illustrates inserting the front legs.

9. Step 9: Insert Rear Legs

   Insert the rear legs into the ends of the rear tube of both the right and left Upper Frame Assemblies (as shown in Figure 9). Figure 9 illustrates inserting the rear legs.

10. Step 10: Attach Wheels and Casters

    Attach each of the casters and front wheels to the high chair feet as shown in Figure 10. Check that all wheels and casters are securely fastened. Figure 10 shows the attachment of wheels and casters.

11. Step 11: Attach Crotch Retainer to Tray

    Flip over the Tray to attach the Crotch Retainer. The molded plastic housing must be oriented with the slot facing the front of the Tray. Insert the 4 (3.5mm X 10) Screws and tighten, but do not over-tighten (as shown in Figure 11). Figure 11 illustrates attaching the Crotch Retainer.

12. Step 12: Attach Seat Pad to Seat Back

    Loop the flap on the back of the Seat Pad over the top of the Seat Back. Connect the Seat Pad to the Seat Back with the two Elastic Loops. These loops fit over the Attachment Tabs located near the top harness slots (as shown in Figure 12). Figure 12 shows how to connect the Seat Pad to the Seat Back.

13. Step 13: Attach Seat Pad to Seat Base

    Attach the bottom of the Seat Pad to the Seat Base with the two Elastic loops located at the rear of the bottom of the Seat Pad. These loops fit over the Attachment Tabs located on the Seat Base near where the Seat Back and Seat Base Join (as shown in Figure 13). Then, set the Seat Insert onto the Seat Pad. Figure 13 illustrates attaching the Seat Pad to the Seat Base and placing the Seat Insert.

14. Step 14: Thread Harness Straps

    Thread the non-buckle end of the Harness Straps (Harness Attachment Tabs) through the provided slots in the Seat Fabric, Seat Insert, Seat Back, and Seat Base (as shown in Figure 14). Once the tabs are through the slots, rotate them 90 degrees to ensure the straps are firmly in place. Figure 14 shows the process of threading the harness straps.

Operation

Opening the High Chair

Pull the legs apart until fully open and locked (as shown in Figure 15). Push downward on the fold levers (left and right) to ensure the frame is locked open. Figure 15 illustrates opening the high chair.

Always check that the high chair is locked in the open position before using.

The tray is not designed to hold the child in the chair. The child must be secured by the safety harness at all times while in the high chair.

Using the Safety Belt

Place your child's arms through the loops formed by the shoulder and waist straps. Place the crotch strap between your child's legs. Insert the Harness Buckles into the Center Clasp with the Red Button. Adjust shoulder and waist straps for your child's comfort and safety by sliding buckles. Safety straps should fit snugly around your child (as shown in Figure 18). Figure 18 shows adjusting the straps for a snug fit.

Releasing the Safety Belt

Push the Red Button on the Center Clasp; the two Harness Buckles will pop free (as shown in Figure 19). Figure 19 illustrates releasing the safety belt.

Adjusting Seat Height

Squeeze both the left and right levers of the Height Adjustment Bracket and adjust to the ideal position (as shown in Figure 20). Figure 20 shows the 6-position height adjustment.

Always check that the height adjustment bracket is level and both left and right sides are locked before placing the child in the high chair.

Folding the High Chair

Place the Seat Back in the most upright position (as shown in Figure 21). Squeeze the tray release handle and slide the tray out (as shown in Figure 23a). Hang the tray on the hooks located on the back of the rear leg (as shown in Figure 22b). Pull upward on the release levers (located on the sides of the frame) and push the rear legs in the direction of the front legs until folded (as shown in Figure 23). The chair is now ready to put away. Figure 23 illustrates folding the high chair.

DO NOT allow your child to play around a folded high chair as it may fall.

Unfolding the High Chair

Push the legs apart until fully open and locked. Push downward on the fold levers (left and right) to ensure the frame is locked (as shown in Figure 24). Figure 24 illustrates unfolding the high chair.

Attaching and Operating the Tray

To attach the Tray, line up the grooves on the bottom of the tray with the armrests of the high chair. Squeeze the Tray's release handle and slide the tray onto the armrests (as shown in Figure 16a). The Tray has a 3-position adjustment. To adjust the position, squeeze the Tray's release handle located underneath the tray and reposition the tray to the desired position (as shown in Figure 16b). Release the Tray's handle and check that the Tray is securely locked in its new position. Figure 16a and 16b show tray attachment and adjustment.

To attach the Insert Tray: The dishwasher-safe food Tray Insert snaps onto the High Chair Tray and is held in place by tabs on the sides of the Tray. Ensure it snaps into place to prevent the child from removing it. To remove, unsnap the tabs from the tray.

Reclining the Seat

Squeeze the recline lever on the back of the seat and adjust to the preferred recline or upright position (as shown in Figure 17). Be careful not to pinch the child's arms, hands, or legs when adjusting the seat back position. Figure 17 shows how to recline the seat.

Care and Maintenance

Harness Straps and Basket are NOT washable.

Dishwasher Safe Tray Insert

The Tray Insert is dishwasher safe up to 160 degrees Fahrenheit. Do not use scouring pads on the Tray Insert as they will damage the surface and make it more difficult to clean.

High Chair/Tray

Clean the High Chair and Tray after each use with mild household dish soap. Use only a soft bristle brush, sponge, or cloth to clean the surface or remove food particles. DO NOT submerge the High Chair and Tray in water. Surface clean only.

Seat Pad

Refer to the care label on the seat pad for specific cleaning instructions.

To remove the seat pad: Remove Harness Straps by pushing Harness Attachment Tabs through the Harness slots on the Seat Back, Seat Base, and Seat Pad. Remove Elastic Loops from Attachment Tabs on Seat Base and Seat Back.

Non-Washable Seat Pad:

Use a sponge or cloth with mild household detergents to surface clean the seat pad. DO NOT MACHINE WASH the seat pad.

Washable Seat Pad:

Machine Wash COLD DELICATE CYCLE with non-chlorine based Laundry Detergent. DO NOT USE BLEACH. HANG DRY. DO NOT MACHINE DRY.

Basket

NOTE: Some models include a Basket underneath the seat for storage. These models are packaged with the Basket already attached to the Seat Base.

To remove: The Basket is attached by four snaps. Release these snaps for removal.

To attach: Feed snap strips around Basket Slots underneath the Seat Base. Press firmly on the four snaps.