DLD20 LinkDongle™ Manual
Brand: Duratech
Product Type: HEAT Accessories
Technical Specifications
| General Specifications | DLD20 LinkDongle™ |
|---|---|
| Input voltage | 230 VAC |
| Interface | LoRa 865,75MHz |
| Ambient air temperature | -10°C to +40°C |
| Humidity | 10% to 90% RH - non condensing |
| Ingress protection rate | IP54 |
| Size | Height: 107mm Width: 65mm Depth: 20mm |
| Weight | 90g |
Box Contents
The DLD20 LinkDongle™ package includes the DLD20 LinkDongle™ unit and this manual.
About the DLD20 LinkDongle™
The DLD20 LinkDongle™ is an RF module designed for connecting and wirelessly controlling existing Dura Pro or DURA+i heat pumps. It operates in conjunction with the LinkTouch™ system and must be connected to the electronic circuit of the Dura Pro or DURA+i heat pump.
Installation Instructions
⚠ Power off the heat pump and disconnect from mains (230 VAC) prior to the installation of the LinkDongle™.
- Open the top lid of the heat pump.
- Open the electronics lid.
- Locate the RS485 cable. It has a black connector and white, yellow, red & black wires, and is marked with yellow tape.
- Connect the RS-485 cable from the heat pump to the DLD20.
- Find the terminal block which supplies power to the heat pump.
- Remove the original spade connectors from the L (Live) and N (Neutral) terminals. Attach these connectors to the piggyback connectors on the DLD20. The brown wire corresponds to L, and the blue wire corresponds to N.
- Reattach the assembled piggyback connectors back onto the terminal block.
- Locate the SMA antenna connector inside the heat pump's electronics compartment. It will be marked with yellow tape.
- Connect the SMA antenna connector to the DLD20.
- Install the DLD20 within the heat pump's electronics compartment. Ensure that none of the connected cables are bent or damaged.
- Location depending on type of heatpump:
- 10a. DURA+i: Install in the middle of the electronics compartment. Cable ties can be used to secure it in place.
- 10b. DURAPRO-12, -17, -21: Tape the DLD20 to the back of the display housing. Remove the adhesive liner from the back of the DLD20 before attaching.
- 10c. DURAPRO-25S, -28TS: Tape the DLD20 to the metal housing of the heat pump. Remove the adhesive liner from the back of the DLD20 before attaching.
- Reassemble the electronics lid.
- Reassemble the top lid.
- Remove the plastic protection cap from the antenna base.
- Screw the antenna onto the antenna base.
- Ensure the antenna is pointing upwards.
⚠ Reconnect the heat pump to mains (230VAC) and power on after installing the DLD20 LinkDongle™.
Control Functions
For further information on how to pair the heat pump after installing the DLD20 LinkDongle™, please refer to the LinkTouch™ documentation.
Safety Information
Intended Use
This device is an RF connecting device developed for Dura Pro and DURA+i heat pumps. It is operated with the LinkTouch™ or controlled by the LinkMaster™.
Precautions for Setup
- The DLD20 LinkDongle™ should only be installed and connected as described in this manual.
- Protect the cables from being strained, pinched, or bucked.
- Use only the original cables from the heat pump and DLD20 LinkDongle™ for the installation.
- Do not use cables if they are damaged or frayed. In case of damage, contact an authorized technician for repair.
- The DLD20 LinkDongle™ contains no serviceable parts. Do not attempt to service the DLD20 LinkDongle™ yourself. Repair service should be performed by an authorized technician.
Environment / Disposal of Old Equipment
The symbol of a crossed-out waste bin [🗑] on the product, its packaging, or accompanying documents signifies that the product is subject to European Directive 2002/96/EC and national laws for its implementation. These regulations mandate that electrical and electronic products must not be disposed of with household waste. Customers are required to dispose of the product by delivering it to a designated collection station for the treatment and recycling of waste electrical and electronic equipment. The correct disposal of your old appliance is free of charge and helps prevent potential negative consequences for the environment and human health. For more information about disposing of your old appliance, contact your city office, waste disposal service, or the shop where you purchased the product.
Service & Warranty
If you require service or information, or if you encounter a problem, please contact your local dealer. They will liaise with the manufacturer to resolve your issue and are available to assist you.
Further information can be found at www.duratech.be.
Duratech warrants all parts to be free from manufacturing defects in materials and workmanship for a period of two years from the date of retail purchase. This warranty is limited to the first retail purchaser and is not transferable. The manufacturer's liability is limited to the repair or replacement of defective parts. It does not cover costs for labor to remove and reinstall the defective part, transportation to or from the factory, or any other materials required for the repair. This warranty does not cover failures or malfunctions resulting from:
- Failure to properly install, operate, or maintain the LinkDongle™ in accordance with the installation guidelines provided in this manual.
- The workmanship of any installer of the product.
- Abuse, alteration, accident, fire, flood, lightning, rodents, insects, negligence, or acts of God.
- Use of non-factory authorized parts or accessories in conjunction with the product.
LIMITATION OF LIABILITY
This is the only warranty provided by the manufacturer. No one is authorized to make any other warranties on Duratech's behalf. This warranty is in lieu of all other warranties, expressed or implied, including but not limited to any implied warranty of fitness for a particular purpose and merchantability. Duratech expressly disclaims and excludes any liability for consequential, incidental, indirect, or punitive damages for breach of any expressed or implied warranty. This warranty grants you specific legal rights, which may vary by country.
WARRANTY CLAIMS
For prompt warranty consideration, contact your dealer and provide the following information: proof of purchase, model number, serial number, and date of installation. The dealer will contact the manufacturer for instructions regarding the claim and determine the location of the nearest service point.
Regulatory Compliance
This product utilizes radio equipment that fully complies with the European harmonized standards of RED (Radio Equipment Directive) 2014/53/EC. Declarations of conformity covering this product are available for download from the House of Duratech website: www.duratech.be.
Duratech Product Lines
Duratech offers a range of innovative pool products:
DURAVISION - Pool Light Products
- VISION Moonlight
- VISION Spectra
- VISION Adagio Pro
- VISION Pro
- VISION Wall Conduits
- VISION Faces Plates
- VISION Specials
DURALINK - Control Products
- LINK Driver
- LINK Touch
- LINK Controller
- LINK Master
- LINK Accessoires
- LINK Cover
DURAHEAT - Heat Pump Products
- HEAT Hot Splash
- HEAT Sun Spring
- HEAT Dura V
- HEAT Dura Vi
- HEAT Dura +i
- HEAT Dura Pro
- HEAT Accessories
DURACOVER - Pool Cover Products
- COVER Wall Duct
- COVER Cable Duct
- COVER Hanging System
- COVER Tube
- COVER Motor
DURAFLOW - Pool Flow Products
- FLOW Inverter
Contact Details
Propulsion Systems bv
Dooren 72
1785 Merchtem, Belgium
Tel: +32 2 461 02 53
Website: www.duratech.be
Email: info@propulsionsystems.be
Duratech reserves the right to change all or part of the contents of this document without prior notice.
