Victrola V1 Stereo Turntable & S1 Subwoofer

Overview

Top View

A diagram shows the top of the Victrola V1 turntable. Labeled components include: Turntable Platter (the circular disc where the record sits), Slipmat (a mat on the platter), 45 RPM Adaptor (a small disc for 45 RPM records), Tone Arm (the arm holding the needle), Cartridge (the part at the end of the tone arm containing the stylus/needle), Tone Arm Lift Lever (a lever to raise/lower the tone arm), Anti-Skating Knob (a dial to adjust anti-skating force), Tone Arm Counter Weight (a weight at the back of the tone arm), Function Knob (a central control knob), and Back Panel (the rear section of the unit).

Back View

A diagram shows the back of the Victrola V1 turntable. Labeled components include: Dust Cover (a protective cover), Subwoofer RCA Output Jacks (for connecting to a subwoofer), Optical In Jacks (for connecting to a TV via optical cable), Record Speed Switch (to select 33-1/3 or 45 RPM), Line Jack (for audio input), Subwoofer Pair Button (Wireless) (for pairing with a wireless subwoofer), Headphone Jack (for connecting headphones), Aux-In Jack (for connecting auxiliary audio devices), and AC Power Port (for the power cable).

Remote Control

A diagram of the remote control shows the following buttons: Power / Function Button (to turn the unit on/off and cycle through modes), and Volume Control (plus and minus buttons to adjust volume).

Quick Start Guide

Function Knob - Basic Operation

POWER: Press and hold for 1-2 seconds to turn the unit ON or OFF.

VOLUME: Rotate the knob to raise or lower volume.

Function Knob - To Cycle Through Features

VINYL: Press to enter record player function mode.
VINYL STREAM: Press to connect the unit to an external Bluetooth speaker or headphones.
BLUETOOTH: Press to pair the unit with a Bluetooth device (smartphone).
OPTICAL IN (TV): Press to play audio from a connected TV.
AUX-IN: Press to play audio from a connected auxiliary device.

Operation and Ring Color Prompts

POWER ON: Press and hold for 1-2 seconds. The dial will illuminate WHITE.
POWER OFF: Press and hold for 1-2 seconds. The unit will return to the last used function mode upon powering back ON.
VINYL PLAYING: Press the Function Knob. The dial will illuminate WHITE and prompt "Vinyl".
VINYL STREAM: Press the Function Knob. The dial will flash WHITE when searching for a device, and turn SOLID WHITE when connected, with a prompt "Connected". In this mode, internal speakers are disengaged.
BLUETOOTH: Press the Function Knob. The dial will flash BLUE when searching for a device, and turn SOLID BLUE when connected, with a prompt "Connected".
OPTICAL IN (TV): Press the Function Knob. The dial will illuminate WHITE and prompt "TV Optical".
AUXILIARY IN: Press the Function Knob. The dial will illuminate WHITE and prompt "Auxiliary".
RAISE VOLUME: Rotate the dial CLOCKWISE. The dial will brighten when in use. A chime sounds at maximum volume.
LOWER VOLUME: Rotate the dial COUNTER-CLOCKWISE. The dial will brighten when in use.

Remote Control Functions

POWER / FUNCTION BUTTON: Press and hold for 1-2 seconds to turn the unit ON/OFF. Quickly press to cycle through each feature.
VOLUME CONTROL: Press '+' to raise volume, press '-' to lower volume.

Remote Control Battery Replacement

The remote control uses 2x AAA batteries. Ensure correct polarity (+ and -) alignment. Refer to the "Safety Info" section for battery warnings and cautions.

Simple Setup

Getting Started

Remove the needle cover by gently pulling it towards the front of the unit. Carefully plug in the unit, install the platter, and attach the tone arm weight. Note: It is recommended that this product be operated only from the type of power source indicated on the rating label. This unit uses AC power and is powered by a standard wall outlet.

Basic Operation

Using the Function Knob, press and hold for 1-2 seconds to turn the unit ON or OFF. Cycle through the Function Knob to select from the following playing modes: VINYL (Playing a Vinyl record), VINYL STREAM (Connecting to an external Bluetooth speaker or headphone), BLUETOOTH (Connecting and playing music from a Bluetooth device), OPTICAL IN (TV) (Connecting and playing audio from a connected TV), AUX-IN (Connecting and playing music from an auxiliary device).

Volume

Rotate the Function Knob to raise or lower the volume.

RCA Line Out

Use the red & white plugs on the back of the unit to connect to an amplifier/stereo device. Reduce the volume on the record player to a minimum level before connecting (RCA cord not included).

Headphone Jack

Use the headphone jack on the back of the unit to connect your headphones/earbuds. Reduce the volume on the record player to a minimum level before connecting.

Platter / Belt Drive Installation

Step 1: Place the turntable platter onto the turntable spindle. The belt is pre-installed underneath the platter.
Step 2: Locate the guide string taped to the platter. Carefully remove the tape while holding the string.
Step 3: Use the guide string to loop the belt over the motor spindle. Once the belt is on the motor spindle, discard the guide string.

Tone Arm Setup

IMPORTANT: The tone arm must be set up as instructed below, or damage may occur to the unit or records.

Setup Steps

Identify the weight on the back of the tone arm. Use the included 2.5mm hex key to loosen the set screw.
Remove the needle cover. Lift the tone arm out of its holder to the left so it floats freely, ensuring it does not touch anything.
Turn the counter weight on the back of the tone arm until the tone arm is flat and balanced horizontally.
Set only the "Number" ring so that "0" is in the top-most position. Do not let the rear weight turn independently of the number ring.
Holding both the number ring and the counter weight, rotate counterclockwise 1.5 rotations until you reach "1", then tighten the set screw.
Once the counter weight is set, adjust the anti-skate control to the recommended setting of "1.5".

Counterweight Purpose

The purpose of the counter weight is to set the tone arm to 3 grams of downward force, which is the recommended tracking weight for the included cartridge. One full counterclockwise turn of the counter weight is equal to 2g.

Anti-Skating Adjustment

The anti-skating function helps compensate for inward tracking force that occurs with certain records when the stylus nears the center or end of the record. After setting the counterweight, adjust the anti-skate control. For the included cartridge, the recommended setting is "1.5". If you notice excessive skipping or the tonearm pulling inward or outward, you can adjust the anti-skate as needed.

Vinyl Playing

Playing a Vinyl Record

Before use, ensure the tone arm is properly set up (refer to the Tone Arm Setup page). Using the Function Knob, press and hold for 1-2 seconds to turn the unit ON. Press the Function Knob to ensure it is in Vinyl mode (the dial will illuminate white). Remove the needle cover by gently pulling towards the front of the unit. Select the proper record speed (refer to the back of the unit). For 45 RPM records, use the included 45 adaptor. Release the tone arm from its holder and gently place it on the record using the lift lever. Rotate the Function Knob to adjust the volume if needed.

Notes:

Make sure to only touch the center or edges of the record to avoid damage to the vinyl grooves.
Do not adjust the counter weight while playing a record, as this could break the needle and scratch the record.
If no sound is playing, the unit may be in Vinyl Stream mode. Cycle through the function knob to ensure it is in Vinyl mode.

The record will stop spinning automatically when playback is complete. To stop manually, lift the tone arm from the record and return it to its rest.

Vinyl Stream

Playing a Vinyl Record on an External Bluetooth Speaker or Headphones

Using the Function Knob, press and hold for 1-2 seconds to turn the unit ON. Press the Function Knob to ensure it is in Vinyl Stream mode (the dial will flash white). Turn ON your external Bluetooth speaker or headphones and set it to pairing mode. Wait a few seconds for the unit to find your device. The unit will chime and say "Connected", while the Function Knob will remain white. Use your external device to control the volume.

Notes:

In Vinyl Stream mode, the internal speakers will be disengaged.
It is recommended to place the Bluetooth device within 1 meter (3.3 feet) of the product when initially pairing.
Ensure the unit is within 10 meters (33 feet) from your external device for the strongest connection.
Vinyl Stream is only compatible with vinyl record playback.
The product stays in pairing mode for 30 seconds. If pairing is not completed, repeat the steps from the beginning after turning all devices OFF.

Bluetooth Pairing

Connecting and Playing Music from a Bluetooth Device (Smartphone)

Using the Function Knob, press and hold for 1-2 seconds to turn the unit ON. Press the Function Knob to ensure it is in Bluetooth mode (the dial will flash blue). On your device, turn Bluetooth ON and search for or select "V1 SYSTEM" in the settings menu. The unit will chime and say "Connected", while the Function Knob will remain blue. Use your external device to control playback. Rotate the Function Knob to adjust the volume if needed.

Notes:

Ensure the unit is within 10 meters (33 feet) from your external device for the strongest connection.
If no sound is playing, the unit may be in Vinyl Stream mode. Cycle through the function knob to ensure it is in Bluetooth mode.

Optical In / Aux-In Listening

Connecting and Playing Audio from a Connected TV (Optical In)

Using the Function Knob, press and hold for 1-2 seconds to turn the unit ON. Press the Function Knob to ensure it is in Optical In (TV) mode (the dial will illuminate white). Plug one end of the Optical In cable (included) into the Optical In socket on the back of the unit. Plug the other end of the cable into the Optical In socket of your TV. Ensure your TV is outputting sound to the Optical In Socket via your TV Settings. Adjust the volume on your TV.

Connecting and Playing Audio from an Auxiliary Device (Aux-In)

Using the Function Knob, press and hold for 1-2 seconds to turn the unit ON. Press the Function Knob to ensure it is in Auxiliary In mode (the dial will illuminate white). Plug one end of the Aux-In cable (not included) into the Aux-In socket on the back of the unit. Plug the other end of the cable into the Aux-In Jack of your device. Adjust the volume on your device.

Subwoofer Pairing

Wireless Pairing the S1 Subwoofer (Sold Separately)

Turn on the S1 Subwoofer. Press the MODE button on the back of the unit until the LED turns BLUE. The LED will slowly flash BLUE, indicating it is in Wireless Mode. Press and hold the MODE button for 1-2 seconds to enter Pairing Mode. The LED will begin to quickly flash BLUE. On the V1 Turntable, press and hold the PAIR button on the back of the unit for 1-2 seconds. You will hear the pairing notification from the V1. Once both the V1 and S1 are paired, you will hear a connection chime. The BLUE LED on the back of the S1 will remain solid.

Cartridge Replacement

Replacement Cartridge: Victrola VPC-190

The VPC-190 Cartridge is rated for over 1000 hours of normal use. As soon as you notice a change in sound quality or damage to the stylus, it is recommended that it be changed.

Replacement Steps

Unplug the unit and put the needle cover on the old cartridge.
Carefully remove all the wire leads from the back of the old cartridge.
Loosen the 2 allen head screws with the included 2mm hex keys on the top of the tone arm / cartridge. Remove the old cartridge.
Mount the new cartridge, and adjust its position to ensure it will track parallel to the record grooves, then tighten the screws.
Connect the wire leads to the new cartridge by pushing them firmly onto the connector pins: WHITE (Left channel positive), RED (Right channel positive), BLACK (Left and Right channel negative).

For best results, use a cartridge alignment protractor or download one from victrola.com/cartridgealignment.

Specifications

General

Power Requirements: AC 100-240V~50/60Hz
Power Consumption: 20 W
Speaker power: 2 x 10W(RMS), (PMPO 40W)
Dimensions (W x D x H): 350mm x 420mm x 120mm (approx)
Weight: 6.15 kgs

Record Player

Motor: DC servo motor
Drive System: Belt Drive
Speeds: Off/33-1/3 rpm, 45 rpm
Cartridge Type: Moving Magnetic Cartridge
Moving Magnetic Cartridge Model: Victrola VPC-190

Bluetooth

Bluetooth Version: Bluetooth V5.0
Bluetooth Profiles: A2DP, AVRCP
Bluetooth Frequency range: 2.402GHz-2.480GHz
Operating Distance: 10 meters (33 ft.)

Included

V1 Music System & Dust Cover
45 RPM Adapter
Remote Control (Batteries Included)
Silicone Slipmat
Digital Optical Cable
Power Cable
Instruction Manual
Quick Setup Guide
2mm/2.5mm hex key

Important Safety Instructions

General Safety

Read these instructions: All safety and operating instructions should be read before this product is operated.
Keep these instructions: The safety and operating instructions should be retained for future reference.
Heed all warnings: All warnings on the appliance and in the operating instructions should be adhered to.
Follow all instructions: All operating and use instructions should be followed.
Do not use this apparatus near water: The appliance should not be used near water or moisture, for example, in a wet basement or near a swimming pool, and the like.
Clean only with a dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Protect the power cord from being walked on or pinched, particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug the apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as the power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, has been exposed to rain or moisture, does not operate normally, or has been dropped.

Electrical Hazard Warnings

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

Warning: To reduce the risk of electric shock, do not remove the cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance.

This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.

The mains plug is used as a disconnect device; the disconnect device shall remain readily operable.

Fire and Moisture Warnings

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases, shall be placed on the apparatus.

Environmental and Usage Warnings

The use of the equipment is intended for moderate climate.
WARNING: Please refer to the information on the exterior bottom/back enclosure for electrical and safety information before installing or operating the apparatus.
The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table-cloths, curtains, etc.
No naked flame sources, such as lighted candles, should be placed on the apparatus.
Do not install this equipment in a confined space such as a book case or similar unit.

Safety Information

General Safety Precautions

In order to shut off power to this product completely, unplug the power cord from the wall outlet. Be sure to unplug the unit if you do not intend to use it for an extended period of time, such as during a vacation.
Use of controls, adjustments, and performance of procedures other than those specified herein may result in hazardous radiation exposure.
To prevent electric shock, match the wide blade of the plug to the wide slot and fully insert it.
If this product experiences problems during operation, contact qualified service centers and do not use the product in defective states.

Before Use

Choose the unit installation location carefully. Avoid placing it in direct sunlight or close to a source of heat. Also avoid locations subject to vibrations and excessive dust, cold, or moisture. Keep away from sources that hum, such as transformers or motors.
Do not open the cabinet, as this may result in damage to the circuitry or electrical shock. If a foreign object should get into the set, contact Customer Service.
Be sure not to handle records with dirty fingers. Never play a record that has a crack on the surface.
When removing the power plug from the wall outlet, always pull directly on the plug, never pull the cord.
To protect the stylus, don't forget to put on the white protective needle cover after use.
Do not attempt to clean the unit with chemical solvents, as this might damage the finish. Use a clean, dry cloth.
In order to shut off the power to this product completely, unplug the power cord from the wall outlet. Be sure to unplug the unit if you do not intend to use it for an extended period of time, such as a vacation.
Keep this manual in a safe place for future reference.

Battery Safety Information

This unit uses 2x "AAA" batteries. Ensure that their polarity markings ("+" and "-") match the remote's markings. When the distance required between the remote control and the main unit decreases, it is necessary to replace the batteries with new ones.

Battery Precautions

Be sure to insert the batteries with the correct positive "+" and negative "-" orientation.
ALWAYS use batteries of the same type. Never mix different types of batteries together.
Caution: There is a risk of explosion if the battery is replaced by an incorrect battery type.
When using rechargeable batteries, refer to the precautions on their labels.
When the remote control unit is not to be used for a long time (more than a month), remove the batteries to prevent them from leaking.
Do not heat or disassemble batteries, and NEVER dispose of old batteries by throwing them in a fire.
Do not dispose of the device into standard garbage disposal sites. Dispose of the device at available Battery Recycling Sites after fully discharging the battery. Failure to do so may violate disposal laws and regulations. Please refer to local regulations for proper battery disposal.

FCC Statement

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Guidelines

WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

The device must not be co-located or operating in conjunction with any other antenna or transmitter. To maintain compliance with the FCC's RF exposure guidelines, place the product at least 20cm from nearby persons.

Industry Canada Compliance (IC Statement)

This device complies with RSS247 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Déclaration d'IC sur l'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux radiations définies par le Canada pour des environnements non contrôlés. Cet équipement doit être installé et utilisé à une distance minimum de 20 cm entre l'antenne et votre corps. Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne ou un autre émetteur.

Warranty Information

Victrola Limited Warranty

Victrola is a registered trademark of Innovative Technology Electronics, LLC.

United States Warranty

Victrola (Innovative Technology Electronics, LLC) warrants to the original retail purchaser that this product will be free from defective materials and workmanship for one (1) year from the date of purchase, subject to the limitations below. This warranty period is not extended if Victrola replaces the product.

To obtain a replacement under the terms of this warranty, you must contact the dealer from which it was purchased with your original receipt. If assistance from the dealer is impossible, you may contact customer service for warranty assistance at victrola.com/contact.

Except as limited below, if the product proves defective in either material or workmanship within one (1) year from the date of purchase, Victrola will replace the product at no charge. If the product model is no longer available and cannot be replaced with an identical model, Victrola will issue a merchandise credit for the purchase price to be redeemed at victrola.com.

Warranty Limitations

This limited warranty does not cover failure of the product arising, in whole or in part, from improper installation, storage, transportation, misuse, abuse, accident, neglect, mishandling, unauthorized repair, modification, or wear from ordinary use or environmental deterioration.
This limited warranty does not cover cosmetic damage, including paint damage, or consequential damage to other components or premises which may result for any reason from the failure of the product.
This limited warranty is null and void for products not used in accordance with Victrola's instructions.
This limited warranty terminates if the original retail purchaser sells or otherwise transfers this product.
This limited warranty is null and void for defects or damage caused by installation or repair performed by any person or entity other than a Victrola authorized installer or dealer.

Legal Rights and Liability

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state, jurisdiction to jurisdiction, or country to country. All express and implied warranties for the product, including but not limited to any implied warranties of merchantability and fitness for a particular purpose, are limited in time to the term of this warranty. Some states, jurisdictions, or countries do not allow the exclusion of certain implied warranties or conditions, or limitations on how long an implied warranty or condition lasts, so this limitation may not apply to you. Victrola's responsibility for malfunctions and defects in hardware is limited to replacement or repair as set forth in this warranty statement. Victrola does not accept liability for special, punitive, consequential, or incidental damages or losses, whether direct or indirect, including without limitation, any liability for third-party claims against you for damages or losses or for products not being available for use. The maximum liability for which Victrola may be responsible will be no more than the amount you paid for the product that is the subject of the claim. Some states, jurisdictions, or countries do not allow the exclusion or limitation of special, indirect, incidental, or consequential damages, so the above limitation or exclusion may not apply to you.

Canada and US Territories

The warranty on this product shall comply with applicable law when sold to a consumer in Canada or a US Territory. To obtain any applicable warranty service, please contact the dealer from which you purchased the product, or the distributor that supplied the product, with your original receipt. If assistance from the dealer is impossible, you may contact customer service for warranty assistance at victrola.com/contact. If this product proves defective in either material or workmanship, Victrola will replace the product at no charge. If the product model is no longer available and cannot be repaired effectively or replaced with an identical model, Victrola, at its sole option, may replace the unit with a current model of equal or greater value.

Outside the U.S., Canada, and US Territories

The warranty on this product shall comply with applicable law when sold to a consumer outside of the United States, Canada, and US Territories. To obtain any applicable warranty service, please contact the dealer from which you purchased the product, or the distributor that supplied the product, with your original receipt.

S1 Subwoofer

Overview

Back View

A diagram shows the back panel of the S1 Subwoofer. Labeled components include: RCA IN Ports (for audio input), Mode Button (to cycle through input modes), Volume Knob (to adjust audio volume), Crossover Knob (to adjust frequency range), Power Switch (to turn the unit ON/OFF), Sub-In Port (for wired subwoofer connection), LED (indicator light), and AC Power Port (for the power cable).

Quick Start Guide

Mode Button - To Cycle Through Features

BLUETOOTH: Press to pair the unit.
SUB-IN: Press to play audio from a subwoofer connection.
RCA-IN: Press to play audio from a connected auxiliary device.

Operation and Function

POWER ON/OFF: Flip the Power Switch to ON or OFF the Unit.
VOLUME KNOB: Turn the Knob to Raise or Lower the Volume.
CROSSOVER KNOB: Turn the Knob to Boost or Reduce the Frequency Sound Range.
MODE Button for BLUETOOTH: The LED will FLASH when searching. Once connected, the LED will turn SOLID BLUE.
MODE Button for SUB-IN: The LED will turn PURPLE.
MODE Button for RCA-IN: The LED will turn RED.

Simple Setup

Basic Operation

Using the Power Switch, flip the unit's power ON. Connect your S1 using one of the wired or wireless pairing modes shown below. Ensure the S1 is in the proper mode based on the MODE LED color guide on the Quick Start Guide.

Setting the Volume

Set the volume knob on the S1 to the middle setting and begin playing music through the connected speakers at an appropriate level. With the music playing, adjust the volume knob on the S1 up or down to match the main speaker volume according to your preference. After adjusting, the master volume on the connected audio device will control the S1 simultaneously with the speaker's volume.

Wired Connection

Hardwiring the S1 Subwoofer

Option A (SUB-IN)

Connection 1: Use the single SUB-IN port if you are connecting a receiver/audio device with a SUB-OUT port and you are using a single RCA subwoofer cable (sold separately).
Connection 2: Use the single SUB-IN port if you are connecting a receiver/audio device with Left and Right pre-outs instead of a single SUB-OUT port, by using the included subwoofer Y cable. Connect the R and L RCA ends to the external device, and the single RCA end to the SUB-IN port on the back of the S1.

Option B (RCA IN)

Connection 1 (most common for wired connections with the Victrola V1 or M1 using the included Y cable): Use the Left and Right RCA inputs if you are connecting a receiver/audio device with a Single SUB-OUT port and you are using the included subwoofer Y cable. The Single RCA end of the Y cable will connect to the external device, and the R & L RCA ends will connect to the back of the S1.
Connection 2: Use the Left and Right RCA inputs if you are connecting a receiver/audio device with Left and Right pre-outs using a standard 2-male to 2-male RCA cable (sold separately).

Wireless Pairing

Wireless Pairing the V1 Turntable (Sold Separately)

Turn on the S1 Subwoofer and V1 Turntable. Press the MODE button on the back of the Subwoofer until the LED turns BLUE. The LED will slowly flash BLUE, indicating it is in Wireless Mode. Press and hold the MODE button for 1-2 seconds to enter Pairing Mode. The LED will begin to quickly flash BLUE. On the V1 Turntable, press and hold the PAIR button on the back of the unit for 1-2 seconds. You will hear the pairing notification from the V1. Once both the V1 and S1 are paired, you will hear a connection chime. The BLUE LED on the back of the S1 will remain solid.

Specifications

General

Power Requirements: AC 100-240V~50/60Hz
Power Consumption: 70 W
Horn: 6.5" woofer x1
Dimensions (W x D x H): 230mm x 230mm x 279mm (approx)
Weight: 4.75 kgs

Bluetooth

Bluetooth Version: Bluetooth V5.0
Bluetooth Profiles: A2DP, AVRCP
Bluetooth Frequency range: 2.402GHz-2.480GHz
Operating Distance: 10 meters (33 ft.)

Included

S1 Subwoofer
RCA Y Cable
Power Cable
Instruction Manual
Quick Setup Guide

Warning

Important Safety Instructions

Read these instructions: All safety and operating instructions should be read before this product is operated.
Keep these instructions: The safety and operating instructions should be retained for future reference.
Heed all warnings: All warnings on the appliance and in the operating instructions should be adhered to.
Follow all instructions: All operating and use instructions should be followed.
Do not use this apparatus near water: The appliance should not be used near water or moisture, for example, in a wet basement or near a swimming pool, and the like.
Clean only with a dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Protect the power cord from being walked on or pinched, particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug the apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as the power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, has been exposed to rain or moisture, does not operate normally, or has been dropped.

Electrical Hazard Warnings

Warning: To reduce the risk of electric shock, do not remove the cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance.

This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.

The mains plug is used as a disconnect device; the disconnect device shall remain readily operable.

Fire and Moisture Warnings

Environmental and Usage Warnings

The use of the equipment is intended for moderate climate.
WARNING: Please refer to the information on the exterior bottom/back enclosure for electrical and safety information before installing or operating the apparatus.
The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table-cloths, curtains, etc.
No naked flame sources, such as lighted candles, should be placed on the apparatus.
Do not install this equipment in a confined space such as a book case or similar unit.

Safety Information

General Safety Precautions

In order to shut off power to this product completely, unplug the power cord from the wall outlet. Be sure to unplug the unit if you do not intend to use it for an extended period of time, such as during a vacation.
Use of controls, adjustments, and performance of procedures other than those specified herein may result in hazardous radiation exposure.
To prevent electric shock, match the wide blade of the plug to the wide slot and fully insert it.
If this product experiences problems during operation, contact qualified service centers and do not use the product in defective states.

Before Use

Choose the unit installation location carefully. Avoid placing it in direct sunlight or close to a source of heat. Also avoid locations subject to vibrations and excessive dust, cold, or moisture. Keep away from sources that hum, such as transformers or motors.
Do not open the cabinet, as this may result in damage to the circuitry or electrical shock. If a foreign object should get into the set, contact Customer Service.
Be sure not to handle records with dirty fingers. Never play a record that has a crack on the surface.
When removing the power plug from the wall outlet, always pull directly on the plug, never pull the cord.
To protect the stylus, don't forget to put on the white protective needle cover after use.
Do not attempt to clean the unit with chemical solvents, as this might damage the finish. Use a clean, dry cloth.
In order to shut off the power to this product completely, unplug the power cord from the wall outlet. Be sure to unplug the unit if you do not intend to use it for an extended period of time, such as a vacation.
Keep this manual in a safe place for future reference.

Battery Safety Information

Battery Precautions

Be sure to insert the batteries with the correct positive "+" and negative "-" orientation.
ALWAYS use batteries of the same type. Never mix different types of batteries together.
Caution: There is a risk of explosion if the battery is replaced by an incorrect battery type.
When using rechargeable batteries, refer to the precautions on their labels.
When the remote control unit is not to be used for a long time (more than a month), remove the batteries to prevent them from leaking.
Do not heat or disassemble batteries, and NEVER dispose of old batteries by throwing them in a fire.
Do not dispose of the device into standard garbage disposal sites. Dispose of the device at available Battery Recycling Sites after fully discharging the battery. Failure to do so may violate disposal laws and regulations. Please refer to local regulations for proper battery disposal.

FCC Statement

FCC Compliance

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Guidelines

WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Industry Canada Compliance (IC Statement)

Warranty Information

Victrola Limited Warranty

Victrola is a registered trademark of Innovative Technology Electronics, LLC.

United States Warranty

Warranty Limitations

This limited warranty does not cover failure of the product arising, in whole or in part, from improper installation, storage, transportation, misuse, abuse, accident, neglect, mishandling, unauthorized repair, modification, or wear from ordinary use or environmental deterioration.
This limited warranty does not cover cosmetic damage, including paint damage, or consequential damage to other components or premises which may result for any reason from the failure of the product.
This limited warranty is null and void for products not used in accordance with Victrola's instructions.
This limited warranty terminates if the original retail purchaser sells or otherwise transfers this product.
This limited warranty is null and void for defects or damage caused by installation or repair performed by any person or entity other than a Victrola authorized installer or dealer.

	Victrola Premiere V1 Stereo Turntable: Setup, Operation, and Specifications Comprehensive guide to the Victrola Premiere V1 Stereo Turntable, covering setup, basic operation, Bluetooth pairing, vinyl playback, cartridge replacement, and technical specifications. Includes safety information and warranty details.
	Victrola V1 Stereo Turntable (VPA-583) User Manual and Setup Guide Comprehensive guide for the Victrola V1 Stereo Turntable (Model VPA-583), covering setup, operation, features like Bluetooth and Vinyl Stream, cartridge replacement, specifications, and safety information.
	Victrola T1 Turntable: Setup, Operation, and Specifications Comprehensive guide to the Victrola T1 Turntable, covering setup, tone arm adjustment, vinyl playback, Bluetooth streaming, cartridge replacement, specifications, and safety information.
	Victrola T1 Turntable (VPT-1000) Quick Start Guide and Setup Learn how to set up, operate, and maintain your Victrola T1 Turntable (VPT-1000). This guide covers basic operation, speaker connection, tone arm setup, vinyl playback, and cartridge replacement.
	Victrola Revolution GO VSC-750SB Portable Record Player User Manual & Quick Start Guide Comprehensive guide for the Victrola Revolution GO VSC-750SB portable record player, detailing setup, operation modes (Vinyl, Bluetooth, Vinyl Stream), safety warnings, specifications, and warranty information.
	Victrola VPT-800 Automatic Turntable Instruction Manual This manual provides comprehensive instructions for setting up, operating, and maintaining the Victrola VPT-800 Automatic Turntable. Learn about unpacking, platter installation, connecting to speakers via Bluetooth or RCA, playing records, replacing the stylus, troubleshooting common issues, and product specifications.
	Victrola V50-200 Bluetooth Stereo Turntable with CD Player Instruction Manual User manual for the Victrola V50-200 Bluetooth Stereo Turntable with CD Player. Covers setup, operation for vinyl, CD, radio, Bluetooth, AUX, maintenance, and troubleshooting.
	Victrola Stream VPT-2000 Instruction Manual This document provides comprehensive instructions for the Victrola Stream VPT-2000 turntable, covering its overview, included parts, technical specifications, app setup, safety warnings, and warranty information.