Victrola VPT-800 Automatic Turntable Instruction Manual

1 UNPACK

Locate the following items:

1. Turntable
2. Dust cover
3. Platter with belt
4. Slipmat
5. 45 RPM adapter
6. Power adapter / RCA cable

Visual Description: An illustration shows the Victrola automatic turntable with its lid open, displaying the platter, tonearm, and controls. Separate images show the dust cover, platter with belt, slipmat, and power adapter.

2 INSTALL PLATTER

Place turntable on a flat and level surface.

1. Lower the platter onto the turntable.
2. Rotate the platter until the hole with the white ribbon is directly over the gold motor.
3. Pull both ends of the ribbon outward until the belt is extended past the motor.
4. Slowly release the belt until it is secured around the motor, then remove the ribbon. Ensure the belt is flat against the motor and not twisted.
5. Place the slipmat on the platter.

Visual Description: A series of close-up images illustrate the steps: placing the platter, aligning the belt with the motor, pulling the belt, and placing the slipmat.

3 PREPARE TURNTABLE

Complete all steps before use:

1. Plug in power adapter.
2. Place 45 RPM adapter in the corner compartment.
3. Remove foam support from the back of the tonearm.
4. Remove the tonearm twist tie.
5. Remove tape and clear stylus cover. Gently pull stylus cover forward to remove.

Visual Description: Images show the rear of the turntable with the DC IN port for the power adapter, the 45 RPM adapter being placed in a compartment, and the tonearm with foam support and twist tie removed, and the stylus cover being removed.

4 CONNECT TO SPEAKERS

MULTI-FUNCTION BUTTON

1. Press and hold to power ON / OFF.
2. Single press to switch output modes:
   • RCA OUTPUT: LED flashes white, then solid white.
   • VINYLSTREAM™ (BLUETOOTH OUTPUT): LED flashes blue.

When powering back ON, the turntable will return to the last used output mode.

Visual Description: An image shows the multi-function button and the status LED on the turntable.

PAIR BLUETOOTH SPEAKER OR HEADPHONES

1. Enter VINYLSTREAM (Bluetooth output) mode; the turntable will automatically enter pairing mode (LED: Flashes blue).
2. Make sure your Bluetooth device is in pairing mode.
3. The turntable will automatically pair to your Bluetooth device.
4. Once paired, the LED will turn solid blue for one second, then turn solid white.

Volume is controlled by the Bluetooth device.

Visual Description: An illustration depicts the turntable, a separate Bluetooth speaker, and a wireless connection symbol, indicating the pairing process.

CONNECT RCA OUTPUT

1. Connect the turntable to external speakers or receiver using the included RCA cable.
   • RED PLUG - Insert into the RED (RIGHT) JACK.
   • WHITE PLUG - Insert into the WHITE (LEFT) JACK.
2. Set the pre-amplifier switch to the correct output:
   • LINE - If connecting to a line-level input.
   • PHONO - If connecting to a phono-level input.
3. For PHONO output, it is recommended to use a grounding wire (not included) to connect the ground pin between the turntable and the external component.
4. Enter wired (RCA) output mode. The LED will flash white, then solid white.

Visual Description: Images show the rear panel connections, including the RCA output jacks (red and white) and the LINE/PHONO switch.

5 PLAYING A RECORD

AUTOMATIC OPERATION

1. Place record on platter.
2. Select record size (preset to 12").
3. Select record speed (preset to 33 RPM).
4. Press the PLAY button to automatically begin playing. The turntable will automatically begin playing. At the end of the record, the tonearm will auto-return to the resting position. To manually stop, press the PLAY button again.

Visual Description: Images show the turntable controls, highlighting the platter, speed/size selection buttons, and the PLAY button.

PLAYING A 7" RECORD

1. Locate the 45 RPM adapter.
2. Place the adapter over the center spindle.
3. Select correct record size and speed.
4. Place record over adapter, begin playback.

Visual Description: Images show the 45 RPM adapter being placed on the spindle and a 7-inch record being placed on top of it.

USING REPEAT MODE

Repeat mode will continuously replay the record until disabled.

1. Press the REPEAT button to activate.
2. When activated, the repeat LED will turn on.
3. Press the REPEAT button again to disable.

Visual Description: An image highlights the REPEAT button on the turntable controls.

MANUAL OPERATION

For manually adjusting playback location:

1. Press the UP / DOWN button to raise the tonearm.
2. Use the finger lift to align the stylus over the record.
3. Press the UP / DOWN button again to lower tonearm.

Visual Description: Images show the UP/DOWN buttons for tonearm control and the finger lift on the tonearm.

MAINTENANCE

REMOVING THE DUST COVER

1. With the dust cover open, firmly grasp both sides of the dust cover near the hinges.
2. Pull the dust cover straight up and away from the turntable; hinges will come off with the dust cover.

Visual Description: An image shows how to grasp and lift the dust cover from its hinges.

REPLACING THE STYLUS

REMOVING THE STYLUS FROM THE TONEARM:

1. Place your fingers at the tip of the stylus and push down in direction "A". WARNING: When applying force to stylus, too much may damage or break the cartridge.
2. Pull the stylus out toward direction "B".

Visual Description: Diagrams labeled "A" and "B" illustrate the direction to push and pull the stylus for removal.

INSTALLING THE STYLUS: (Replacement Stylus # ATN3600L)

1. Hold the tip of the stylus and insert the other edge by pressing toward direction "C".
2. Push the stylus up toward direction "D" until it locks at the tip.

CAUTION:

• Do not bend or force the stylus into the cartridge.
• Do not touch the stylus needle to avoid injury to your hand.
• Turn off the unit's power before you replace the stylus.
• Keep out of reach of children.

NOTE: The stylus should last about 300 hours under normal use. It is recommended that the stylus be replaced as soon as you notice a change in sound quality. 78 RPM records may accelerate stylus wear and may have to be changed sooner.

Visual Description: Diagrams labeled "C" and "D" illustrate the correct way to insert and lock the new stylus.

TROUBLESHOOTING

BLUETOOTH WILL NOT PAIR:

• Place your Bluetooth device closer to the turntable during initial pairing.
• Ensure your Bluetooth device has not paired to its maximum number of devices.

TURNTABLE WILL NOT SPIN OR SPINNING IS INCONSISTENT:

• Ensure the belt is properly installed around the motor spindle.
• Ensure the belt is not twisted.

CAN'T HEAR AUDIO:

• If using Bluetooth, ensure the volume is turned up on your Bluetooth device.
• If using RCA output, ensure you are using the correct pre-amp output setting.

FACTORY RESET

Quickly press the multi-function button 3 times to factory reset the turntable. This will remove any previously paired Bluetooth devices. The LED will flash blue and the turntable will power off.

SPECIFICATIONS

GENERAL

• DIMENSIONS: 4.01" H x 14.96" W x 13.77" D (102mm H x 380mm W x 350mm D)
• WEIGHT: 5.95 lbs / 2.7 kg

POWER

• INPUT: 100-240V ~ 50/60Hz
• OUTPUT: 12V/0.5A
• CONSUMPTION: 6.0W

TURNTABLE

• SPEEDS: 33-1/3 & 45 RPM
• REPLACEMENT STYLUS: ATN3600L

BLUETOOTH

• BLUETOOTH VERSION: Bluetooth V5.0
• SUPPORTED PROFILES: A2DP, AVRCP
• OPERATING DISTANCE: 10 meters (33 ft.)

INCLUDED:

• Automatic Turntable, Dust cover, Platter, Slipmat, 45 RPM adapter, Power adapter, RCA cable, Instruction manual.

Please note: As a result of continual improvements, the design and specifications of this product are subject to change without notice. Bluetooth is a registered trademark of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners. Made in China. This product has been manufactured and sold under the responsibility of Innovative Technology Electronics, LLC. Victrola is a trademark used under license by Innovative Technology Electronics, LLC. Further information at victrola-brand.com. All other products, services, companies, trademarks, trade or product names and logos referenced herein are the property of their respective owners.

SAFETY WARNINGS

Please read safety instructions and respect the following warnings before the appliance is operated:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

Visual Description: Warning symbols are present: a lightning flash with an arrowhead within an equilateral triangle (alerting to uninsulated "dangerous voltage"), a "CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN." box, and an exclamation point within an equilateral triangle (indicating important operating and maintenance instructions).

• Always follow basic safety precautions, especially when children are present.
• Children should be supervised to ensure they do not play with the appliance.
• Do not damage the power cord; do not place heavy objects on it, stretch, or bend it. Do not attach extension cables, as damage can cause fire or electric shock.
• If the supply cord is damaged, it must be replaced by the manufacturer, a service agent, or similarly qualified persons to avoid a hazard.
• Ensure the unit is plugged into an AC 100-240V 50/60Hz power outlet. Using higher voltage may cause malfunction or fire.
• If the power plug does not fit your outlet, do not force it.
• Turn off the unit before unplugging it from the power source.
• Do not disconnect or connect the power cord with wet hands, as this may cause electric shock.
• Ensure the main plug is always easily accessible.
• This product contains no user-serviceable parts. In case of a fault, contact the manufacturer or authorized service department. Exposing internal parts may be dangerous. Manufacturer's guarantee does not cover faults caused by unauthorized repairs.
• Ensure this product is used in moderate climates only (not tropical/subtropical climates).
• Place the product on a flat, stable surface not subject to vibrations.
• Ensure the product and its parts are not overhanging the edge of the supporting furniture.
• To reduce the risk of fire, electric shock, or damage, do not expose the product to direct sunlight, dust, rain, or moisture. Never expose it to dripping or splashing, and do not place objects filled with liquids on or near the product.
• Do not place objects filled with liquids, such as vases, on the apparatus.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Do not place the product where humidity is high and ventilation is poor.
• Do not mount this product on a wall or ceiling.
• Do not place the unit near TVs, speakers, or other objects that generate strong magnetic fields.
• Do not leave the unit unattended when in use.
• Allow at least 30cm clearance from the rear and top of the unit, and 5cm from each side. Always ensure ventilation openings are not covered by items like newspapers, tablecloths, or curtains.
• NEVER let anyone, especially children, push anything into holes, slots, or other openings in the unit's casing, as this could result in a fatal electric shock.
• Storms are dangerous for all electric appliances. If main or aerial wiring is struck by lightning, the appliance might get damaged, even if turned off. Disconnect all cables and connectors before a storm.
• Excessive sound pressure from headphones can cause hearing loss.
• Do not cover ventilation openings; this is not intended to be used on soft support.

MAINTENANCE:

• Unplug the power cable from the power source before cleaning the appliance.
• Use a soft clean rag to clean the outside of the unit. Never clean it with chemicals or detergent.

POWER ADAPTER:

• To disconnect the unit from the main supply, unplug the lead from the main socket.
• Only use the supplied main adapter, as failure to do so may result in a safety risk and/or damage to the unit. The main plug of the power adapter is used as the disconnect device. The socket-outlet shall be installed near the equipment and shall be easily accessible.

Visual Description: Symbols are shown for AC Voltage, DC Voltage, Class II equipment, Indoor use only, Energy Efficiency marking with level VI, and Polarity of D.C. power connector. A recycling symbol is also shown.

The symbols shown above appear on electrical and electronic equipment (or packaging) to remind users of this. Users are requested to use existing return facilities for used equipment and batteries.

FCC & IC WARNINGS

FCC STATEMENTS

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with part 15 of the FCC rules and Innovation, Science and Economic Development Canada's license-exempt RSS standard(s). Operation is subject to the following two conditions:

• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation.

French Translation: Le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de license. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) L'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC & IC RADIATION EXPOSURE STATEMENT:

This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment. This device complies with RSS247 of Industry Canada. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

French Translation: DÉCLARATION D’IC SUR L’EXPOSITION AUX RADIATIONS: Cet équipement est conforme aux limites d'exposition aux radiations définies par le Canada pour des environnements non contrôlés. Cet appareil se conforme à RSS247 de Canada d'Industrie. Cet équipement doit être installé et utilisé à une distance minimum de 20cm entre l'antenne et votre corps. Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne ou un autre émetteur.

LIMITED WARRANTY

Victrola is a registered trademark of Innovative Technology Electronics, LLC.

United States

For detailed information about our warranty policy and limitations visit victrola.com/pages/warranty.

Outside the U.S., Canada, and US Territories

The Warranty on this product shall comply with applicable law when sold to a consumer outside of the United States, Canada, and US Territories. To obtain any applicable warranty service, please contact the dealer from which you purchased the product, or the distributor that supplied the product, with your original receipt.

Canada and US Territories

The Warranty on this product shall comply with applicable law when sold to a consumer in Canada or a US Territory. To obtain any applicable warranty service, please contact the dealer from which you purchased the product, or the distributor that supplied the product, with your original receipt.

If assistance from the dealer from which it was purchased is not possible, you may contact our customer service for warranty assistance at victrola.com/contact.

CUSTOMER SUPPORT

Website: VICTROLA.COM/PAGES/CUSTOMER-CARE

Email: support@victrola.com

Phone: (877)483-2497

Visual Description: A QR code is shown, linking to warranty information. This has been replaced by the text link above.