JLab Audio JBuds BT Bluetooth Earbuds

Initial Setup: Bluetooth Pairing

1. Turn on Bluetooth on your device's settings.

   [Visual Description: A smartphone screen showing the Bluetooth setting turned on.]

2. Press and hold the button on the earbuds for more than 10 seconds. Release the button. A flashing red and blue light indicates pairing mode.

   [Visual Description: An illustration of the earbud's control button. A red and blue light is shown flashing.]

3. On your device's Bluetooth settings, select "JLab BT". A slow blue flashing light indicates successful Bluetooth pairing.

   [Visual Description: A smartphone screen showing the Bluetooth menu with "JLab BT" selected, and a slow blue flashing light indicator.]

Repeated Use

After initial pairing with your device, the earbuds will automatically connect to your Bluetooth device when powered on. (Follow the Button Functions section for operation).

Button Functions

• Volume Up: Single press.
• Next Track: Press and hold for more than 2 seconds.
• Power On: Press and hold for 3 seconds.
• Power Off: Press and hold for 5 seconds.
• Play/Pause / Answer/End Call: Single press.
• Activate Siri (iOS) or "OK Google" (Android): Double press.
• Bluetooth Pairing: (Follow initial setup steps: Bluetooth Pairing).
• Volume Down: Single press.
• Previous Track: Press and hold for more than 2 seconds.

EQ Modes

Quickly press both buttons to cycle through different EQ settings (JBuds BT 3 cycles through EQ settings):

• JLab SIGNATURE (One Beep): JLab C3™ Signature, the brand's unique sound with enhanced sound effects and bass.
• BALANCED (Two Beeps): Even volume, without additional bass enhancement.
• BASS BOOST (Three Beeps): Enhanced bass and sub-bass.

Indicator Lights

• Power On: Chime sound.
• Bluetooth Connected: 2 Beeps.
• Low Battery: "Low battery" alert (less than 20%).
• Power Off: Chime sound.

Charging

1. To charge, open the USB port cover and connect the cable to a computer or a USB power source.

   Ensure the power source voltage is 5V or lower.

   [Visual Description: An illustration showing the earbud's USB port being connected to a USB cable, which is then connected to a computer or power adapter.]

2. While charging, the indicator light remains solid red and turns blue when charging is complete.

   [Visual Description: Two states of the indicator light: one solid red for charging, and one solid blue for fully charged.]

Wearing the Earbuds

1. First, attach the Cush Fin™ flexible support, then the ear tip.

   Note: Types and options may vary.

   [Visual Description: An illustration showing the earbud with the "Cush Fin™ Flexible Support" and "Ear Tip" components separately, and then attached to the earbud.]

2. Rotate the flexible support to the desired position.

3. For the best fit, try different ear tips and flexible supports.

Using the Cable Management Clip

1. Attach the cable management clip approximately halfway up the cable.

   [Visual Description: An illustration showing the clip being attached to the earbud cable.]

2. Clip it to the front or back of your clothing.

   [Visual Description: An illustration showing the clip attached to the front and back of clothing.]

Troubleshooting

Cannot See JLab BT Option on My Device

1. Turn off and then on Bluetooth on your device's settings.

   [Visual Description: A smartphone screen showing the Bluetooth setting being toggled off and on.]

2. If the JLab BT option is still not visible, repeat the steps from the Initial Setup: Bluetooth Pairing instructions.

JLab BT Not Connecting to My Device After Power On

1. In your device's settings, forget or remove the JLab BT option.

   [Visual Description: A smartphone screen showing the "JLab BT" device selected in Bluetooth settings, with an option to "Forget" or "Remove" it.]

2. Turn off and then on Bluetooth on your device's settings.

3. Repeat the steps from the Initial Setup: Bluetooth Pairing instructions.

Bluetooth Connecting to an Unwanted Device

Note: JLab BT can remember up to 8 devices. It will automatically try to connect to the most recently used device.

1. If you have connected to more than one device, turn off Bluetooth on the unwanted devices.

   Then, turn on Bluetooth on the desired device.

   [Visual Description: Two smartphone screens. The first shows "JLab BT" connected to one device. The second shows turning off Bluetooth on that device and then turning it on for another device.]

2. Press and hold the button for more than 10 seconds. Release the button. A flashing red and blue light indicates pairing mode.

   Select "JLab BT" on your device's settings. A slow blue flashing light indicates successful Bluetooth pairing.

Warnings and Care

Important:

• Ensure the USB port cover is closed and secured. This protects it from sweat and water.
• The JLab BT earbuds must be completely dry before charging. If exposed to any moisture, internal components may be damaged. It is recommended to air dry them before charging.
• Avoid getting moisture or liquids into the earbuds or charging port.
• Avoid extreme high or low temperatures, or humidity.
• Avoid dropping or crushing the earbuds. Do not strain the cable by yanking or applying excessive force, or by bending the cable at sharp angles.
• Earwax may accumulate in the ear tips, reducing sound quality. To improve sound quality, carefully remove earwax with a dry cotton swab or other small tool.
• If you experience discomfort or pain, try reducing the volume or temporarily discontinue using the device.
• If you experience persistent discomfort while using the product, discontinue use and consult a doctor.
• It is recommended to treat your earbuds like a pair of expensive sunglasses: store them in a safe place when not in use.