Manuals+

EK-Quantum Reflection PC-011D XL D5 PWM D-RGB

DISTRIBUTION PLATE USER GUIDE

Basic Guidelines

Before you start using this product, please follow these basic guidelines:

Box Contents

The following components are included in the box:

Preparing the 011D XL Chassis

Before installing the distribution plate, carefully read the PC case manual.

STEP 1

Unscrew the factory provided screws and remove the top panel from the case.

STEP 2

Remove both side panels and the front panel from the case.

STEP 3

The SSD Trays also need to be removed from the back side of the chassis. Once the distribution plate is secured, they can be reinstalled as required.

STEP 4

For easier installation of the distribution plate, remove the Fan/SSD Tray from the bottom of the case. Unscrew the two (2) marked factory screws and remove the Fan/SSD Tray. After securing the distribution plate, it can be reinstalled with the bottom radiator and fans.

Installing the Distribution Plate in the 011D XL

STEP 1

Carefully place the EK-Quantum Reflection PC-011D XL D5 PWM D-RGB distribution plate into the PC case and align the mounting holes at the back.

STEP 2

Secure the distribution plate to the chassis with two (2) M3 x 6 DIN7380 screws and M3 nuts, as shown in the diagram.

STEP 3

Position the front mounting bracket onto the distribution plate and secure it with five (5) M3 X 8 DIN7991 mounting screws.

Recommended Distribution Plate Configurations

A diagram shows the various ports on the distribution plate, labeled as:

It is mandatory to use at least one of each type of port, and all remaining ports should be sealed using the supplied plugs. The EK-Loop Multi Allen Key (6mm, 8mm, 9mm) may be used to install all EK fittings. Do not use excessive force.

If one of the prescribed components will not be installed (e.g., bottom radiator or GPU block), then one IN and one OUT port must still be joined together in order for this distribution plate to function!

Exterior fill and drain ports are also indicated.

Connecting the D-RGB LED Strip

Plug the 3-pin connector of the distribution plate D-RGB LED light to the D-RGB HEADER on the motherboard. The LED will work if the pin layout on the header is as follows: +5V, Digital, Empty, Ground.

Connecting the Pump

The EK-D5 PWM pump has two connectors:

  1. 4-pin Molex: It must be connected directly to your PSU at all times as it is used to power the pump.
  2. 4-pin PWM fan: It can be connected to your motherboard's CPU Fan or designated water pump header. It can also be connected to a controller. This cable is used to control and report the rotational speed of the pump. If it's not connected, the pump will run at maximum speed (100% PWM).

Testing the Loop

To make sure the installation of EK components was successful, we recommend performing a leak test for 24 hours.

When your loop is complete and filled with coolant, connect the pump to a PSU outside of your system. Do not connect power to any of the other components. Turn on the PSU and let the pump run continuously. It is normal for the coolant level to drop during this process as air collects in the distribution plate.

Inspect all parts of the loop, and in the eventuality that coolant leaks, fix the issue and repeat the testing process. Ensure that all hardware is dry before the system is powered on in order to prevent any damage.

Support and Service

For assistance, please contact:

http://support.ekwb.com/

EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU

Social Media

PDF preview unavailable. Download the PDF instead.

69bfa57736bda08d43ae444c7a21c827af1f Adobe PDF Library 15.0 Adobe InDesign 15.0 (Windows)

Related Documents

Preview EK-Quantum Reflection Obsidian 1000D Distribution Plate User Guide
User guide for the EK-Quantum Reflection Obsidian 1000D distribution plate, detailing installation, port configurations, D-RGB LED connection, pump connection, and leak testing for PC liquid cooling systems.
Preview EK-Quantum Inertia D5 PWM Installation Manual
Comprehensive installation guide for the EK-Quantum Inertia D5 PWM pump, detailing unboxing, mounting, connections, and testing for PC liquid cooling systems.
Preview EK-Quantum Reflection² V3000 Plus D5 PWM D-RGB - Plexi Distribution Plate User Guide
This comprehensive user guide provides detailed instructions for the EK-Quantum Reflection² V3000 Plus D5 PWM D-RGB - Plexi distribution plate. Learn about its features, installation, port configuration, and maintenance for your custom PC water cooling loop.
Preview EK-Quantum Kinetic³ FLT D5 PWM D-RGB Installation Manual
Comprehensive installation guide for the EK-Quantum Kinetic³ FLT D5 PWM D-RGB reservoir and pump combination, covering box contents, dimensions, technical specifications, mounting instructions, and connectivity.
Preview EK-XTOP Revo D5 PWM Installation and Mounting Manual
This manual provides detailed instructions for installing and mounting the EK-XTOP Revo D5 PWM pump top, covering pump preparation, drilling mounting holes, assembling the XTOP with the pump, attaching fittings, and proper priming procedures. It also includes important disclosures regarding leak testing, warranty, and product usage.
Preview EK-Pro Pump Reservoir Manifold X6 D5 – Acetal User Guide
Comprehensive user guide for the EK-Pro Pump Reservoir Manifold X6 D5 – Acetal, detailing installation, specifications, and usage for PC liquid cooling systems.
Preview EK-Quantum Velocity² D-RGB AM5 CPU Water Block User Guide
Comprehensive user guide for the EK-Quantum Velocity² D-RGB AM5 CPU water block, detailing installation, compatibility, technical specifications, parts lists, warranty, and support information for PC liquid cooling enthusiasts.
Preview EK-Quantum Surface Radiator Setup Configurations - User Guide
This user guide provides detailed setup configurations, flow direction options, and component breakdowns for EKWB's EK-Quantum Surface Radiators, including S, P, and X series. It covers installation guidelines, port usage, and support information.