Ergotron WorkFit C Single LCD Mount, HD
User's Guide
This document provides installation and adjustment instructions for the Ergotron WorkFit C Single LCD Mount, HD, featuring Constant Force™ Technology.
Hazard Symbols Review
These symbols alert users of safety conditions requiring attention. All users should recognize and understand the significance of the following Safety Hazards.
| Symbol | Signal Word | Level of Hazard |
|---|---|---|
| ℹ️ | NOTE | A NOTE indicates important information that helps you make better use of this product. |
| ⚠️ | CAUTION | A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. |
| ❗ | WARNING | A WARNING indicates either potential for property damage, personal injury, or death. |
| ⚡ | ELECTRICAL | An Electrical indicates an impending electrical hazard which, if not avoided, may result in personal injury, fire and/or death. |
Safety
Important! You will need to adjust this product after installation is complete. Ensure all your equipment is properly installed before attempting adjustments. The product should move smoothly and easily through its full range of motion and stay where set. If movements are too easy or difficult, or if the product does not stay in desired positions, follow the adjustment instructions. Any time equipment is added or removed, resulting in a change in the mounted load's weight, repeat these adjustment steps.
❗ IMPACT HAZARD: MOVING PARTS CAN CRUSH & CUT
Do not remove the [zip tie] and [cardboard spacer] which keep the hand brake from disengaging until instructed. Removing them before the cart is unpacked and standing upright may cause unintended motion of the riser, leading to personal injury or equipment damage.
❗ IMPACT HAZARD: Moving Parts Can Crush & Cut
Do not tip the cart over on its side. The cart must remain upright at all times. Tipping the cart may cause unintended motion of the riser, resulting in serious personal injury or property damage.
For more information on safe set-up, adjustment, and use, refer to the user manual at www.ergotron.com or contact Ergotron Customer Care at 1-800-888-8458.
Weight Capacity and Dimensions
Weight Capacity: 40 lbs. (18 kg)
Multilingual capacity information is provided (Spanish, French, German, Dutch, Italian, Japanese, Chinese). All indicate 40 lbs (18 kg).
Configuration Weight Limits:
- A: 16 - 28 lbs (7.3-12.7 kg)
- B: ≤ 5 lbs (2.25 kg)
- C: ≤ 2 lbs (0.9 kg)
- D: ≤ 1.5 lbs (0.68 kg)
- Total A+B+C+D: ≤ 31 lbs (14 kg)
Dimensions:
- 2.6" - 8.5" (66 - 216 mm)
- 9.4" - 15.75" (239 - 400 mm)
- 5" (127 mm)
- 20" (508 mm)
- Angles: 20°, 10°
Operation: Release brake to move riser. (Multilingual instructions provided).
Parts and Hardware
The following parts and hardware are included:
Category A:
- 1x Vertical Support
Category B:
- 1x Base Plate
- 2x M6 x 22mm screws
- 2x M6 x 16mm screws
Category C:
- 1x M3 x 6mm screw
- 1x M5 x 8mm screw
- 2x M6 x 16mm screws
- 4x M6 x 7mm screws
- 4x M4 x 10mm screws
- 6x M3 x 6mm screws
- 2x M6 x 7mm screws
- 1x M5 x 22mm screw
Category D:
- 4x M4 x 10mm screws
Also included:
- 1x 5-sided Security Wrench
- 1x 14mm Tool
Installation Steps
Step 1
Prepare the base. [60 minute timer icon] indicates a recommended time. Text: Sterile Alcohol Prep.
Step 2
Attach the vertical support to the base using the provided hardware.
Step 3
Attach the main vertical support to the base using two M6 x 16mm screws and two M6 x 22mm screws. A 4mm tool is shown.
Step 4
Mount the monitor bracket to the vertical support using M3 x 6mm screws. Ensure 0° orientation. M4 x 10mm screws are also shown.
Step 5
Attach the monitor to the bracket using M6 x 7mm screws and M5 x 8mm screws. A 4mm tool and the 5-sided security wrench are indicated.
Step 6
Prepare for cable management. ✂️ are shown.
Step 7
Release brake to move riser. Multilingual instructions provided.
Step 8
8a: Cable management preparation. Cut zip ties and remove spacer. Use 3mm tool for adjustments. Use 5-sided security wrench for adjustments.
8b: Route cables through the management system.
8c: Secure cables with clips.
8d: Use 5-sided security wrench for final adjustments on cable management.
8e: Final cable routing.
Step 9
9a: Attach monitor bracket to riser using M5 x 8mm screws. [5-sided security wrench] indicated. Text: NOTE: Center on bottom.
9b: Attach monitor to bracket using M5 x 22mm screws. [5-sided security wrench] indicated.
9c: Secure monitor to bracket.
9d: Route cables for monitor.
Step 10
10a: Attach keyboard tray support to riser. Use 3mm tool for adjustments.
10b: Use 3mm tool for adjustments. CAUTION: Do not over-tighten fasteners. Over-tightening may cause damage to fasteners.
Step 11
Secure the keyboard tray to the support using the 5-sided security wrench and M5 x 22mm screws.
Step 12
12a: Attach keyboard tray to support using M5 x 8mm screws.
12b: Use 5-sided security wrench for adjustments.
12c: Final attachment of keyboard tray.
Step 13
13a: Attach keyboard tray to support using M5 x 8mm screws.
13b: Use 5-sided security wrench for adjustments.
Step 14
14a: Route cables through the system.
14b: Secure cables using M5 x 22mm screws and the 5-sided security wrench.
Step 15
Secure cables using 6x zip ties and 2x cable clips. M3 x 6mm screws are used.
Cable Management
NOTE: Leave enough slack in cables to allow full range of motion.
Caution: To avoid pinching cables, follow the cable routing instructions. Failure to do so may result in equipment damage or personal injury.
Diagram shows routing cables and securing them with zip ties and clips.
Adjustment Step
Important! After installation, adjust the product to ensure smooth and easy movement. If movements are too easy or difficult, or if the product does not stay in position, follow these adjustment instructions.
Lift Strength Adjustment
To Increase Lift Strength: If the mounted weight is too heavy or the product does not stay up when raised, use the 14mm tool to turn the adjustment nut clockwise (indicated by ➕). Text: Increase Lift Strength.
To Decrease Lift Strength: If the mounted weight is too light or the product does not stay down when lowered, use the 14mm tool to turn the adjustment nut counterclockwise (indicated by ➖). Text: Decrease Lift Strength.
❗ IMPACT HAZARD: Moving Parts Can Crush And Cut!
Minimize Lift Tension BEFORE:
- Removing Mounted Equipment
- Shipping Cart or Storing Cart
To Minimize Lift Tension:
- With cart upright, lower worksurface to lowest position.
- Turn adjustment nut at bottom of riser counterclockwise until it stops (may require 40-60 revolutions).
WARNING: Cart Must Remain Upright! Tipping Cart On Side May Cause the Work Surface to Disengage Causing Serious Personal Injury and Property Damage.
For more information and instructions, refer to the product guide at www.ergotron.com or contact Ergotron Customer Care at 1-800-888-8458.
Friction Adjustment
To Increase Friction: If the product moves too easily, use the 4mm tool and turn the adjustment screw clockwise (indicated by ➕). Text: Increase Friction.
To Decrease Friction: If the product is too difficult to move, use the 4mm tool and turn the adjustment screw counterclockwise (indicated by ➖). Text: Decrease Friction.
Ergonomics and Support
Learn more about ergonomic computer use at: www.ergotron.com/ergonomics
For Warranty visit: www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit: http://contact.ergotron.com
Contact Information:
- www.ergotron.com
- USA: 1-800-888-8458
- Europe: +31 (0)33-45 45 600
- China: 400-120-3051
- Japan: japansupport@ergotron.com
©2015 Ergotron, Inc. All rights reserved. WorkFit™ is a registered trademark of Ergotron, Inc.
Monitor Mounts, Computer Carts, Sit to Stand Desks | Ergotron
