XBA-RUB8 Bill Acceptor Configuration and Settings
XBA Option Switch Settings (Pulse/MDB/ICT104U/ICT104V)
Supported bill denominations: RUB 10, 50, 100, 200, 500, 1000, 2000, 5000.
| FUNCTION | SW1 | SW2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 |
|---|---|---|---|---|---|---|---|---|
| Inhibit Active HIGH | ON | |||||||
| Inhibit Active LOW | OFF | |||||||
| • Reject RUB 10 (Note.2) | ON | |||||||
| Accept RUB 10 (Note.2) | OFF | |||||||
| • Reject RUB 50 & 100 & 200 | ON | |||||||
| Accept RUB 50 & 100 & 200 | OFF | |||||||
| • Reject RUB 500 & 1000 | ON | |||||||
| Accept RUB 500 & 1000 | OFF | |||||||
| • Reject RUB 2000 | ON | |||||||
| Accept RUB 2000 | OFF | |||||||
| • Reject RUB 5000 | ON | |||||||
| Accept RUB 5000 | OFF | |||||||
| Disable Bill Reject 4 Times BA Stop By 30 Sec | ON | |||||||
| Enable Bill Reject 4 Times BA Stop By 30 Sec | OFF | |||||||
| Stack Banknote when Power-up | ON | |||||||
| Reject Banknote when Power-up | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF |
This dip switch is located at the side of XBA.
Diagram: Visual representation of the side of the XBA unit, highlighting the location of the DIP Switch.
Currency Assign Data
| Interface | Bill value | MDB | ICT104U | ICT104V | Pulse |
|---|---|---|---|---|---|
| SW1 Dip1 | BV1 | RUB 10 | RUB 10 | RUB 10 | RUB 50 |
| BV2 | RUB 50 | RUB 50 | RUB 50 | RUB 100 | |
| BV3 | RUB 100 | RUB 100 | RUB 100 | RUB 500 | |
| BV4 | RUB 500 | RUB 500 | RUB 500 | RUB 1000 | |
| BV5 | RUB 1000 | RUB 1000 | RUB 1000 | RUB 5000 | |
| BV6 | RUB 5000 | RUB 5000 | RUB 5000 | RUB 200 | |
| BV7 | RUB 200 | RUB 200 | RUB 200 | RUB 2000 | |
| BV8 | RUB 2000 | RUB 2000 | RUB 2000 | RUB 2000 |
XBA-RUB8 (Pulse/MDB/ICT104U/ICT104V) - Additional Settings
| FUNCTION | SW1 | SW2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 |
|---|---|---|---|---|---|---|---|---|
| Inhibit Active HIGH | ON | |||||||
| Inhibit Active LOW | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF | |||||||
| Pulse Mode | MDB Mode | ICT104V Mode | ||||||
| Credit-Pulse Normal LOW | Scaling Factor (SF) = 100 Decimal Point Position (DPP) = 2 |
Connect with coin changer | ||||||
| Credit-Pulse Normal HIGH | Scaling Factor (SF) = 1 Decimal Point Position (DPP) = 0 |
Connect with ICT JPSTD converter board |
||||||
| Pulse Mode | Other Mode | ICT104V Mode | ||||||
| VDB Mode | ON | |||||||
| Reserved | OFF | |||||||
| ICT104U Mode | ON | |||||||
| ICT104V Mode | OFF | |||||||
| Pulse Mode | Other Mode | ICT104V Mode | ||||||
| VDB Mode | OFF OFF | |||||||
| Reserved | OFF ON | |||||||
| ICT104U Mode | ON OFF | |||||||
| ICT104V Mode | ON ON |
This dip switch is located on the CPU board; remove the CPU board cover first.
Diagram: Visual representation of the CPU board with a callout pointing to the DIP Switch (labeled as (1)).
Operational Notes
• Manufacturer setting
After setting the dip switch for credit pulses, you should reset the bill acceptor again.
Note:
- Calibration card is needed.
- Pulse Mode: When Dip 1 is OFF, One Pulse per RUB 10.
- Pulse Mode: When Dip 1 is ON, One Pulse per RUB 50.
