What's In The Box
Please inspect the contents of your shipped package to ensure you have received everything that is listed below.
- Cheese Plate (Top)
- Cheese Plate (Bottom)
- 2 x Clamps
- 8 x Elastic Tubes
- 2 x Allen Bolts (Size: 1/4" x 1")
- 8 x Wire Configuration
- Cable Tie
- 14mm & 15mm Spanner
- 2 x Washers
- 1mtr Elastic Tube
- 3/16" Allen Key
All rights reserved. No part of this document may be reproduced, stored in a retrieval system, or transmitted by any form or by any means, electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permitted by the applicable copyright statutes or in writing by the Publisher.
Assembly Instructions
Wire Configuration Assembly
- Loosen the grub screw using a 3/16" Allen key.
[Image: Close-up of a hand using a 3/16" Allen key to loosen a grub screw on a circular component.] - Insert the wire configuration into place.
[Image: A hand inserting a wire bundle into a slot on a plate.] - Re-tighten the grub screw again using a 3/16" Allen key.
[Image: A hand tightening a grub screw with a 3/16" Allen key.] - Repeat the same process to insert the remaining wire configurations.
[Image: A view of the assembled wire configurations on the base plate, forming a star pattern.]
Elastic Tubes Assembly
- Insert the elastic tube into the hole while rotating it 360° for secure placement.
[Image: A hand inserting a black elastic tube into a hole on a plate, with a blue arrow indicating rotation.] - Remove the Allen bolt using a 3/16" Allen key.
[Image: A hand removing an Allen bolt using a 3/16" Allen key.] - Insert the other elastic tube while rotating it 360° for secure placement.
[Image: A hand inserting another elastic tube into a different hole.] - Repeat the same process to insert the remaining elastic tubes.
[Image: A view of the assembled elastic tubes attached to the base plate.]
NOTE: Insert 4 elastic tubes for lighter setups and 8 elastic tubes for heavier setups, according to your convenience.
Cheese Plate (Bottom) Assembly
- Loosen the grub screw on the bottom cheese plate using a 3/16" Allen key.
[Image: Close-up of a hand using a 3/16" Allen key to loosen a grub screw on the bottom cheese plate.] - Next, insert the other end of the wire configuration into the bottom cheese plate.
[Image: A hand inserting the end of a wire configuration into a hole on the bottom cheese plate.] - Tighten the grub screw again using a 3/16" Allen key.
[Image: A hand tightening a grub screw with a 3/16" Allen key.] - Repeat the same process to insert the remaining wire configurations.
[Image: A view of the assembled wire configurations attached to the bottom cheese plate.] - Insert the elastic tube into the hole, rotating it 360° to ensure secure placement.
[Image: A hand inserting an elastic tube into a hole on the cheese plate, with a blue arrow indicating rotation.] - Remove the Allen bolt using a 3/16" Allen key.
[Image: A hand removing an Allen bolt using a 3/16" Allen key.] - Then, insert the other elastic tube while rotating it 360° for secure placement.
[Image: A hand inserting another elastic tube into a hole.] - Repeat the same process to insert the remaining elastic tubes.
[Image: A view of the assembled elastic tubes attached to the cheese plate.] - The wires and elastic tubes are now securely attached to the cheese plates.
[Image: A view showing the wires and elastic tubes securely attached to the cheese plates.]
Clamps Assembly
- Loosen the clamp's bolt and remove it.
[Image: A hand loosening a bolt on a clamp with a knob.] [Image: A hand removing the bolt from the clamp.] - Insert the bolt into the top cheese plate and mount the clamp.
[Image: A hand inserting a bolt through a clamp and into the top cheese plate.] - Then, tighten the bolt using a 14mm spanner.
[Image: A hand tightening the bolt with a 14mm spanner.] - Mount the second clamp using the same process.
[Image: A view of the second clamp being mounted.] - Remove the knobs and take the brackets out of the clamps.
[Image: A hand removing a knob from a clamp bracket.] [Image: A hand taking a bracket out of a clamp.]
Attaching the Vibration Isolator to the Speed Rail
- Attach the Vibration Isolator with the clamps on the speed rail (Not included).
[Image: The PROAIM Aero Mount Vibration Isolator, with clamps attached, being positioned onto a speed rail.] - Then, mount the brackets.
[Image: A hand attaching the isolator to the speed rail.] - Insert all the knobs and tighten them securely.
[Image: A hand inserting a knob into a clamp.] [Image: A hand tightening a knob.] - The Vibration Isolator is now securely attached to the speed rails.
[Image: A view of the assembled isolator mounted on a speed rail.] [Image: A view of the isolator mounted on a speed rail, showing multiple clamps.]
Feature: The clamps fit rods from 38mm to 50mm.
Quick Release Camera Plate Mounting
- Attach the Quick release camera plate (Not included) to the bottom cheese plate.
[Image: A hand attaching a quick release camera plate to the bottom cheese plate.] - Then, insert the Allen bolts (1/4" x 1").
[Image: A hand inserting a 1/4" x 1" Allen bolt.] - Tighten the Allen bolts using a 3/16" Allen key.
[Image: A hand tightening the Allen bolt with a 3/16" Allen key.] - The Quick release plate is now securely attached to the cheese plate.
[Image: A view of the quick release plate securely attached to the cheese plate.]
Gimbal Mounting
- Slide the Gimbal (Not included) into the cheese plate and secure it using the locking lever.
[Image: A hand sliding a gimbal (not included) into the cheese plate.] [Image: A hand securing the gimbal with a locking lever.]
Wide Gimbal Compatibility
Multiple Mounting Threads
[Diagram showing the cheese plate with mounting threads labeled: "1/4"-20 Thread" (indicated by a green line) and "3/8"-16 Thread" (indicated by a blue line).]
Final Setup and Usage
- Attach the Camera (Not included) to the Gimbal and securely lock it.
[Image: A hand attaching a camera (not included) to the gimbal.] [Image: A hand securing the camera with a locking mechanism.] - Your setup is ready to use.
[Image: A wide shot showing the assembled setup (gimbal, vibration isolator, camera) mounted on a stand.]
Adaptable Payload Support
4-Elastics Tubes: For Light Loads (0-10kg / 0-22lb)
8-Elastics Tubes: For Heavier Loads (10-20kg / 22-44lb)
Product Showcase
YOUR PROAIM AERO MOUNT VIBRATION ISOLATOR ALL DRESSED UP AND READY TO GO!
[Image: A PROAIM Aero Mount Vibration Isolator setup mounted on a car's speed rail, with a camera attached to the gimbal. Text below reads: "(SHOWN WITH OPTIONAL ACCESSORIES)".]
Warranty Information
Warranty: PROAIM offers a one-year warranty for its products from the date of purchase. Within this period, PROAIM will repair products without charge for labor or parts. Warranty does not cover transportation costs or damage resulting from misuse or accidental damage. Warranty repairs are subject to inspection and evaluation by PROAIM.
Liability: PROAIM is not liable for damage caused by products not supplied by PROAIM, mishandling during transit, accidents, misuse, neglect, lack of care, or service performed by anyone other than PROAIM.
Contact Us: In case of any dissatisfaction, please contact PROAIM immediately for support.
