PROAIM Ballpro Camera Suction Car Mount with Vibration Isolator (CM-BLPR-01)

What's In The Box

Please inspect the contents of your shipped package to ensure you have received everything that is listed below.

• Suction Car Mount: The primary assembly featuring four suction cups and a central articulating arm structure.
• DJI-QR Plate: A quick-release plate designed for camera gimbals.
• 4 x Yellow Dust Covers: Protective covers for the suction cups.
• P-QRG Plate: A plate for attaching a gimbal.
• 1 x Allen Key: Tool with sizes 4mm and 2.5mm.
• 2 x Allen Bolts: Fasteners with sizes 1/4"-20 x 1-1/4" and 2.5 x 6.
• Foam With Bag Packing: A protective carrying case.

All rights reserved. No part of this document may be reproduced, stored in a retrieval system, or transmitted by any form or by any means, electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permitted by the applicable copyright statutes or in writing by the Publisher.

Ballpro Camera Setup

1. Remove the yellow dust cover from the Suction Car Mount.
2. Similarly, remove the remaining yellow dust covers from the suction mount.
3. Place your first suction cup in the selected position from where you want to shoot.
4. Press down the suction cup and keep pushing the pump to firmly fix it on the surface. Repeat this process for all the suction cups.

   Caution: Recheck the pump every 90 minutes. If the red line is visible, re-pump the cup without losing the remaining vacuum until the red line disappears.

5. The Suction Car Mount is now properly placed on the car.
6. Secure the movement of the ball joint with the help of the ratchet knob of the telescopic legs.

Assembly and Attachment

1. Note: Two ratchet knobs are provided in the Suction Car Mount. With the help of the bottom knob, you can change the ball joint movement of the telescopic legs.

2. Place the DJI-QR Plate on the Suction Car Mount.
3. Insert Allen CSK bolts and tighten with the help of the 4mm Allen key.
4. Follow the same process for other Allen CSK Bolts.
5. The DJI-QR Plate is now properly attached on the Suction Car Mount.
6. Attach the (P-QRG) plate with the Ronin Gimbal (Not-Included) and tighten it properly with the help of a screwdriver.
7. Attach the gimbal by sliding it from the DJI-QR plate of the suction car mount.
8. Tighten the DJI-QR plate with the help of the provided knob.
9. Your Gimbal car suction mount setup is now ready to use.
10. Attach the camera (Not-Included) with the Ronin Gimbal (Not-Included), as shown in the image. (Image description: Hands attaching a camera to a gimbal.)
11. The following is a proper assembled image of the Ballpro Camera Suction Car Mount. (Image description: The PROAIM Ballpro Camera Suction Car Mount with Vibration Isolator, fully assembled and mounted on the windshield of a car, with a camera attached to the gimbal. This view shows the product ready for use, potentially with optional accessories.)

Warranty, Liability, and Support

Warranty: PROAIM offers a one-year warranty for its products from the date of purchase. Within this period, PROAIM will repair products without charge for labor or parts. The warranty does not cover transportation costs, nor does it cover products subjected to misuse or accidental damage. Warranty repairs are subject to inspection and evaluation by PROAIM.

Liability: PROAIM is not liable for damage caused by products not supplied by PROAIM, or from mishandling in transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than PROAIM's authorized personnel.

Contact: In case of any kind of dissatisfaction, please contact PROAIM immediately. PROAIM promises its utmost support and care until you use the product.