Step2 Whisper Ride II Buggy

Product Overview & Safety

Intended for children aged 18 months to 48 months.

Important: Observe all statements and warnings to reduce the likelihood of serious or fatal injury. Save this sheet for future reference.

Safety Warnings:

• ⚠️ CHOKING HAZARD: Small parts. Sharp points. Adult assembly required.
• ⚠️ BURN HAZARD: Always check the temperature of the product before letting children play on it. The product may cause burns. Be aware of sun and weather conditions; do not assume the equipment is safe just because the air temperature is not very high.
• ⚠️ TO AVOID SERIOUS INJURY:
  • Provide adult supervision at all times.
  • Do not use in areas unsafe for pedestrians.
  • Do not use on steps or steep inclines where the product could roll away.
  • Keep away from pools or other bodies of water.
  • Shoes must be worn during use.
  • Allow only one rider per seat.
  • Periodically check the handle and hardware for wear and proper assembly.

Parts List

The following parts are included (refer to diagrams for visual identification):

• A: Handlebar
• B: Seat
• C: Steering Wheel
• D: Front Body Section
• E: Rear Body Section
• F: Wheel (x4)
• G: Wheel Hub Cap (x4)
• H: Steering Wheel Cap
• I: Handlebar Grip (x2)
• J: Screw (1" / 25.40 mm) (x2)
• K: Screw (3/4" / 1.91 cm) (x4)
• L: Axle (x2)
• M: Seat Belt
• O: Washer (x4)
• Q: Screw (3/4" / 1.91 cm) (x2)
• S: Seat Belt Buckle
• T: Washer (x2)
• U: Screw (3/4" / 1.91 cm) (x4)

Parts Not Included: (Refer to diagram for visual identification of what is not included)

Assembly Instructions

General Assembly Notes:

• Adult assembly is required.
• Screws are designed to pierce plastic and form their own threads.
• Do not over-tighten screws.
• Inspect this product before each use. Tightly secure connections and replace damaged or worn components. Contact The Step2 Company, LLC. for replacement parts.

1. Step 1: Attach the front body section (D) to the main chassis. Use screws (J) and part G.
2. Step 2: Insert wheel hub caps (G) into wheels (F).
3. Step 3: Attach the seat (B) to the main body using screws (J).
4. Step 4: Insert axle (L) through the main body.
5. Step 5: Attach a wheel (F) to the axle (L) using a washer (O) and screw (K).
6. Step 6: Repeat the wheel attachment process for the front axle.
7. Step 7: Attach rear wheels (F) to the rear axle assembly.
8. Step 8: Secure wheels (F) with screws (K) and washers (O).
9. Step 9: Insert the steering column into the main body.
10. Step 10: Attach the steering wheel (C) to the steering column.
11. Step 11: Secure the steering wheel (C) with the steering wheel cap (H).
12. Step 12: Attach the handlebar grips (I) to the handlebar (A).
13. Step 13: Insert the handlebar assembly (A) into the main body. Ensure it snaps into place.
14. Step 14: If locking pins do not engage, place a finger in the shaft hole and manually spread the locking pins to engage.
15. Step 15: Attach the front body section (D) to the main chassis.
16. Step 16: Secure the front section with screws (K).
17. Step 17: Attach the seat belt (M) to the seat (B).
18. Step 18: Attach the seat belt buckle (S) to the seat (B).
19. Step 19: Secure the seat belt assembly with screws (Q) and washers (T).
20. Step 20: Attach the rear handle assembly.
21. Step 21: Attach handlebar grips (I) to the handlebar (A).
22. Step 22: Secure the handlebar assembly.
23. Step 23: Attach the push handle assembly.
24. Step 24: Secure the push handle assembly.
25. Step 25: Insert the push handle into the main body.
26. Step 26: Adjust the handle position. Do not over-tighten.
27. Step 27: Attach the steering wheel (C) to the steering column.
28. Step 28: Final assembled product view.

Care and Maintenance

Cleaning Instructions:

General Cleaning: Use a 50/50 mixture of white vinegar and water.

Decal Application:

Clean and dry the area thoroughly. Center the decal in the area. Apply pressure from the center to the outer edge.

Disposal Instructions:

Please recycle when possible. Disposal must be in compliance with all government regulations.

Safety Information Summary:

• Maximum weight per seat: 50 lbs (22.68 kg).
• Instruct children:
  • Not to use product until properly assembled.
  • To keep hands, feet, loose clothing, and long hair away from the wheels during use.
• DO NOT remove any screws once installed. For disassembly, only remove parts not secured by screws.
• DO NOT over-tighten screws or they will not hold parts together appropriately.
• Take notice that screws are designed to pierce the plastic and form their own threads.
• Seat belt is only intended to keep child seated. Fasten securely across waist.

General Maintenance:

Inspect this product before each use. Tightly secure connections and replace damaged or worn components. Contact The Step2 Company, LLC. for replacement parts.