Introduction
Thank you for purchasing the DOD Mini Volume Pedal. This is a miniature passive volume pedal designed to provide a full range of volume control without taking up valuable space on your pedalboard.
Features:
- Small footprint: Takes up minimal space on your pedalboard.
- Long treadle: Provides a full range of control.
- High-quality 500k potentiometer: Offers smooth volume adjustments with a high cycle rating.
- Built-in treble bleed circuit: Prevents treble loss at lower volume settings.
- Removable rubber feet: For mounting on a pedalboard.
- 1/4" TS input and output jacks.
- Non-slip treadle pad.
- Rugged construction.
Setup
Follow these steps for initial setup:
- Turn off your amplifier and connect your cables. (Note: The original document mentions a wiring diagram but none is provided. Ensure you use unbalanced TS cables.)
- Lower your amplifier's volume, press the toe of the DOD Mini Volume Pedal down, and then turn on your amplifier.
- Slowly increase your amplifier's volume until you reach the desired level.
Important Usage Notes
The two hex screws on the bottom of the pedal are part of the spring adjustment mechanism. If you notice slipping over time, slightly loosen these screws and then retighten them. This will re-engage the main drive gear against the treadle gear. DO NOT remove these screws or tamper with the pedal while the screws are loose, as this can cause gear misalignment and pedal malfunction. There are no user-serviceable components inside the pedal. DO NOT open the pedal under any circumstances.
Compliance and Safety Instructions
The following text indicates use at low altitudes; do not use this product above 2000 meters (approx. 6560 feet).
Safety Symbols
The symbols below are internationally recognized symbols that warn of potential hazards associated with electrical products:
- ⚡️ Lightning bolt with an arrow in an equilateral triangle: Indicates the presence of dangerous voltage within the unit.
- ⚠️ Exclamation mark in an equilateral triangle: Indicates that the user needs to consult the user manual.
These symbols warn that there are no user-serviceable parts inside the unit. Do not open. Do not attempt to repair the unit yourself. Refer all servicing to qualified personnel. Opening the chassis for any reason will void the manufacturer's warranty.
Do not expose the unit to moisture. If liquid spills onto the unit, turn it off immediately and take it to your dealer for service. Unplug the unit during thunderstorms to prevent damage.
Mains Plug Warnings (UK Specific)
A molded mains plug that has been cut off from the cord is unsafe. Dispose of the mains plug in a suitable collection point. NEVER, UNDER ANY CIRCUMSTANCES, PLUG A DAMAGED OR FRAGILE MAINS PLUG INTO A 13AMP SOCKET. Do not use the mains plug without the fuse cover in place. Replacement fuse covers can be obtained from your local dealer. Replacement fuses are 13A and MUST be ASTA approved to BS1362.
Disposal Information
If you wish to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery, and recycling. Private households in the 25 EU member states, Switzerland, and Norway can return their used electronic products free of charge to designated collection points or to a retailer (if you purchase a similar new product). For countries not listed above, please contact your local authorities for the correct disposal method. This ensures that your discarded product undergoes the necessary treatment, recovery, and recycling, preventing potential negative effects on the environment and human health.
General Safety Precautions
READ THE FOLLOWING:
- READ THESE INSTRUCTIONS.
- KEEP THESE INSTRUCTIONS.
- HEED ALL WARNINGS.
- FOLLOW ALL INSTRUCTIONS.
- DO NOT USE THIS APPARATUS NEAR WATER.
- CLEAN ONLY WITH A DRY CLOTH.
- FOR INDOOR USE ONLY.
- DO NOT BLOCK ANY VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS.
- DO NOT INSTALL NEAR ANY HEAT SOURCES such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- USE ONLY ATTACHMENTS/ACCESSORIES SPECIFIED BY THE MANUFACTURER.
- UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding pin. The wide blade or the third pin is for your safety. If the provided plug does not fit your outlet, consult an electrician for replacement of your obsolete outlet. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Servicing
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled into, or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Power Switch
The mains switch used in this unit does NOT interrupt the connection from the mains. MAINS DISCONNECTION: The plug must remain readily operable. For rack mounting or installation where the plug is not accessible, a mains switch must be incorporated into the rack or building's electrical installation for all poles with a contact separation of at least 3 mm in each pole.
When connecting to a 240V supply, use a suitable CSA/UL certified power cord.
Wiring Instructions (Appliance with Supply Cord)
WARNING: THIS APPLIANCE MUST BE CONNECTED TO A SOCKET-OUTLET PROVIDED WITH AN EARTH CONNECTION. The cores in the mains lead are colored in accordance with the following code:
- GREEN AND YELLOW ? ? = EARTH / GROUND
- BLUE ? = NEUTRAL
- BROWN ? = LIVE
As the colors of the cores of the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows:
- The core which is colored GREEN AND YELLOW must be connected to the terminal in the plug marked with the letter E, or by the earth symbol ?, or colored GREEN, or GREEN AND YELLOW.
- The core colored BLUE must be connected to the terminal marked with the letter N or colored BLACK.
- The core colored BROWN must be connected to the terminal marked with the letter L or colored RED.
This unit may require the use of a different type of line cord, plug, or adapter, depending on the power source available at installation. If it is necessary to replace the plug assembly, contact qualified service personnel who should refer to the table below. The GREEN/YELLOW conductor must be connected directly to the unit's chassis.
WARNING: IF THE EARTH CONNECTION IS MADE, SOME FAULT CONDITIONS IN THE UNIT OR THE SYSTEM TO WHICH IT IS CONNECTED MAY RESULT IN FULL MAINS VOLTAGE BETWEEN THE CHASSIS AND EARTH. WHEN SIMULTANEOUSLY TOUCHING THE CHASSIS AND EARTH, THIS MAY RESULT IN SEVERE INJURY OR DEATH.
