JOYOR Electric Scooter User Manual

Model: S8E

Please read this instruction manual fully! This instruction manual contains important safety matters! Do not use the electric scooter until you fully understand the performance of the scooter! Please keep this instruction manual properly!

Front and side views of the JOYOR S8E electric scooter with a seat.

I. Safety Instructions for Use

This product is an electric scooter for adults, limited to one person, and not for riding with others simultaneously. Minors must use it under adult supervision.
Please wear safety helmets and other protective equipment when riding this product.
Do not ride this product in unsafe or illegal places such as motorways.
Please practice in an open space first and drive after skillfully controlling.
Do not perform dangerous actions or ride with one hand while the scooter is driving. Keep your feet on the pedal.
Do not turn off the power supply while the scooter is moving.
Do not attempt to directly pass over steps with a gap of over 3cm, which may overturn the scooter and cause injury or damage. Steps below 3cm should also be avoided as much as possible.
In case of rough or uneven road conditions, please slow down or get off to push the scooter.
Users must adjust the height of the product to the appropriate position to ensure driving safety.
Do not ride this product on slippery roads with oil or ice on the surface.
Do not use this product in an environment below -5 ℃.
Do not immerse the product in water deeper than 3cm and keep it still to avoid damage to electrical parts due to water inflow.
Do not ride in bad weather such as rain, snow, and strong winds to avoid unnecessary injuries.
If you do not use this product for a long time, please charge it at least once within 30 days. The charging port must be kept clean and dry.
Do not expose this product to the sun for a long time. Avoid outdoor storage for extended periods.
Please use the charger equipped with the company's scooter. Do not use other chargers indiscriminately to avoid safety problems.
When charging, ensure someone is present to supervise.
Do not leave it in a severely humid place for a long time.
Plastic bags pose a suffocation risk to babies.

II. List of Main Components and Parameters of Products

a. Main Components (Ref.)

Display
Rear-view mirror
Headlamp
Trumpet
Front wheel
Front disc brake
Front shock absorber
Seat
Folded handle
Folded base
Frame
Brake handle
Front turn signal
Speaker switch
Quick-release grip
Rear light
Rear turn signal
Rear mud block
Rear shock absorber
Rear wheel
Motor
Kickstand

b. Parameter Table (Ref.)

Model	Battery	Range	Max. Speed	Motor	Frame Material	Brake	Tires	Open Size	Folding Size	Package Size
S8E	48V26AH	55-80Km	45Km/h	800W	Aluminium alloy	Front and rear brake	10 inch, pneumatic tire	12386301295mm	12386301227mm	1190250500mm

III. Operation Instruction

a. First Assembling

Follow these steps to assemble the scooter:

Image shows attaching a part to the handlebar stem.
Image shows inserting a screw and using an Allen key.
Image shows tightening screws on the handlebar clamp.
Image shows securing the handlebar stem.
Image shows attaching the display unit with screws.
Image shows tightening screws with an Allen key.
Image shows attaching a component (possibly brake lever) with a wrench.
Image shows attaching a rear-view mirror.
Image shows attaching a rear fender.
Image shows securing the rear fender with screws.
Image shows attaching the seat post.
Image shows attaching the seat to the seat post.

Steps 1-12 illustrate the initial assembly of the JOYOR S8E electric scooter, focusing on the handlebars, display, seat, and fenders.

III. Operation Instruction (cont.)

b. Fold and Expand

Image shows a locking mechanism on the steering column being operated. [Arrow indicating movement]
Image shows the handlebars in their upright position.
Image shows the seat being folded down. [Arrows indicating folding motion]
Image shows the scooter in a partially folded state, with the deck lowered.
Image shows the scooter being folded, with the steering column lowered towards the deck. [Arrow indicating folding motion]
Image shows the scooter in a fully folded state.
Image shows the scooter in its expanded, ready-to-ride state.

Steps 13-21 demonstrate how to fold and unfold the JOYOR S8E electric scooter for storage and transport.

c. Riding Operation

Display Panel Overview:

The scooter's display panel provides various information:

Single-drive / Double drive: Indicates the drive mode.
Speed display: Shows current speed (MPH/Km/h).
GEAR: Gear indicator.
lighting: Headlight status indicator.
Battery display: Shows remaining battery level (represented by battery icons).
Start-up mode: Indicates the current mode (STATE: ECO, NORMAL).
Error code display: Shows error codes if any issues arise.
Power gear display: Shows the current gear.
Cruise: Cruise control indicator.
Turn signal icon: Indicates active turn signals.
USB charging tips: Icon indicating USB charging availability.
6Km/h implementation mode: Indicates a specific speed mode.
Multi-function display: Shows ODO (Odometer), TRIP (Trip meter).

Error Codes:

E-01: Rear-drive Hall failure
E-11: Front-drive Hall failure
E-03: Rear drive controller failure
E-13: Front drive controller failure
E-08: Rear drive blockage failure
E-18: Front drive blockage failure
E-02: Turn fault
E-05: Controller undervoltage failure
E-09: Temperature protection
E-06: Communication failure (device cannot receive controller data)
E-07: Communication failure (controller cannot receive instrument data)
E-04: Brake failure (limited to self-test alarm display)

d. Riding Operation (Controls)

Accelerator: Located on the right handlebar.

Long press for 3 seconds: Start the push function (requires gears 1-3; cancels when braking).
Short press: Reduce gear in the main interface.

Left Handlebar Controls:

Power Button (On/Off):
- Long press for 3 seconds: Turn display on/off.
- Short press: Switch setting options (in setting interface).
'+' Button:
- Long press for 3 seconds: Turn Dual Drive mode on/off (for scooters with two motors).
- Short press: Increase gear in the main interface.
'-' Button:
- Long press for 3 seconds: Enter setting interface or return to main interface.
- Short press: Decrease gear in the main interface.
Horn Button: Short press to ring the horn.
Headlight Button (?): Short press to turn headlights on, press again to turn off.

Turn Signals:

Left Arrow Button: Short press, the left indicator light flashes.
Right Arrow Button: Short press, the right indicator light flashes.

Note on Settings: Press "+"and "-"for 3S to enter the setting interface or return to the main interface. Short press the Power button to switch setting options. After setting, long press "+"and "-"to return to the main interface.

Zero Start Setting: After entering the setting interface, press the Power button to switch to P09. Press "+"and "-"to set to 0.
Note: The system default is 1 (non-zero startup). After startup, it defaults to gear 0. For safety, confirm to start in gear 1. Then press down the handle while sliding your feet to start riding.
Enable Cruise: After entering the setting interface, press the Power button to switch to P16. Press "+"or "-"to select 0 (OFF) or 1 (ON). After starting cruise, press the acceleration handle until the cruise icon lights up. At this time, releasing the handle will not stop assistance. Shifting gears, braking, or pressing the acceleration handle again will exit cruise.
Braking Procedure: If you encounter someone or an obstacle, first release the throttle, then brake with the left brake handle (rear brake), and finally use the right brake handle (front brake) to decelerate or stop.

e. How to Charge

Open the charging hole rotation sleeve and insert the charger output connector into the charging hole on the body.
Plug the charger input into the supply socket (AC110V-220V).
The charger indicator light is red, indicating that charging is in progress. When the indicator turns green, the battery is fully charged.
When charging the battery, please place it in a dry and ventilated environment.

Diagram shows a charger, charger plug, charger port, and a wall socket.

IV. Product Maintenance

Tire: This product uses elastic rubber tires. If the tire shows obvious wear or rupture and needs replacement, contact the dealer for the original tire. Every month, check the scooter for any loose screws and tighten them promptly.

Brake: This product uses front disc brakes and rear drum brakes. Pay attention to checking the thickness of the brake friction plates. If there is significant wear, they should be replaced in time to prevent adverse braking consequences.

Battery: When you get the electric scooter for the first time, please charge the battery before use. If the vehicle is not used for a long time, it must be charged at least once a month. If the battery cannot be charged, please contact after-sales service as soon as possible. Battery damage due to abnormal factors like water inflow and collision is not covered by the warranty.

If the intensity and frequency of use are high, check the scooter's screws monthly and replace them every half year to avoid issues.

The lithium battery has a charging cycle of at least 500 times, generally reaching more than 600 times in normal use. If the battery is fully charged and the mileage is only half of the factory mileage, it is recommended to replace the lithium battery.

V. After-sales Maintenance

Please contact your local dealer for after-sales maintenance.

During the warranty period, faults and damages caused by the following reasons are not covered by the warranty:

The electric scooter was not properly maintained and repaired in accordance with this manual.
The electric scooter is used for purposes other than its intended use, such as performing dangerous actions or special effects, leading to damage or malfunction.
Any self-disassembly or use of parts not from the original factory.
Damage to the scooter body or accessories due to errors, traffic accidents, or accidental collision.
Incomplete labeling, water inflow, and mismatched parts numbers.
Damage or malfunctions due to riding on abnormal roads.
Commercial rental use or improper non-franchise use.
Force majeure events.
Exposure of this product to the sun or rain for extended periods, causing rapid aging and functional failure.

Manufacturer and Licensor Information

Licensor:

WeRoll Tech GmbH

Address: Hausbroicher Str.62, 47877 Willich, Germany

Tel: [Not Specified]

Email: [Not Specified]

Website: [Not Specified]

Manufacturer:

Jinhua Joyor Vehicle Co., Ltd

Address: No.331, Xiashan Natural Village, Xicheng Street, 321300 Yongkang city, Zhejiang Province P.R.CHINA